Projecta EVC2KW is a 2.4KW EV emergency charger designed for easy and safe charging of electric vehicles. Featuring a rainproof IP65 design, it ensures reliable operation even in wet conditions. The charger comes with multiple safety protections, including over-voltage, under-voltage, over-current, over-temperature, leakage current, and short-circuit protection, giving you peace of mind during charging.
Projecta EVC2KW is a 2.4KW EV emergency charger designed for easy and safe charging of electric vehicles. Featuring a rainproof IP65 design, it ensures reliable operation even in wet conditions. The charger comes with multiple safety protections, including over-voltage, under-voltage, over-current, over-temperature, leakage current, and short-circuit protection, giving you peace of mind during charging.
TYPE 2 2.4KW
EV EMERGENCY CHARGER
P/No. EVC2KW
WARNING
• Only use for EV charging. Not designed for other applications.
• Do not use the portable charger if the device is damaged.
• Do not open any part of the device by yourself.
• Do not disconnect while the device is charging.
• Please follow the user manual to use this device.
• Regularly check the portable charger for visible damage, there may be an electric shock
hazard when using the damaged product.
• Do not modify, retrofit, or change any part of the charger under any circumstances.
• Ensure a stable service life and operation of the charging cable by keeping the
environment clean and with a constant temperature and humidity. The charging cable
must not be used in the presence of flammable gases and liquids.
• Ensure the charger is used for 240VAC 50Hz. 10Amp.
• If the charger fails to operate correctly as per the instructions, do not use it, and seek
advice from PROJECTA customer support.
• Ensure the 240V plug is not connected via an adapter. High current is required.
• Please ensure the product is plugged directly into the wall socket and not via an
extension cord.
2
SPECIFICATIONS
PART NO. EVC2KW
POWER PLUG AS/NZS 3112
CABLE LENGTH 5m (Total length)
CHARGING RATE 10A (2.4KWH)
RATED INPUT VOLTAGE 230V AC ±10%
RATED OUTPUT VOLTAGE 230V AC ±10%
INSULATION RESISTANCE OF CABLE >1000MΩ (DC500V)
WIRING HARNESS SIZE 3 X 2.5mm2 + 1 X 0.5mm2
DELAY START TIMER 2h, 4h, 6h, 8h
3
FEATURES
• Charging your EV when away has never been easier with this 2.4KW charger. It is
designed to plug into a standard 10Amp socketed outlet.
• The rainproof IP65 design instills confidence in its safety and usability, even if exposed
to rain droplets.
• The charger is protected with safety in mind to protect the customer.
• Quick and easy to use! Simply connect the charger to the EV’s inlet and the charger
will automatically detect the connection status and handshaking protocol, then start
charging.
• The rugged and durable ABS enclosure is designed to last the test of time.
• The charger is fitted with an intelligent microprocessor that can highlight problems with
the charging process and will indicate this on the display.
• The charger is fitted with over-voltage protection, under-voltage protection, over-
current protection, over-temperature protection, leakage current protection, short-circuit
protection.
• The charger is fitted with an In Cord - Control and Protection Device (IC-CPD) which
allows communication between the EV vehicle and the charger.
4
INSTRUCTIONS FOR USE
START
• Connect the power cord.
• Press button for 3 seconds to set delay start timer (2/4/6/8 hrs) or skip this step without
timer
• Plug into car,
• Charging...
FINISH
• Pull plug out.
• Power off.
• Cover the rubber cap.
• Store in the store bag.
NOTE: Please see the images below on how to use the charger. The charger can delay
start by pressing the button for 3 seconds. Ensure the charger is connected to mains
power and not connected to the EV vehicle.
Cable length 4200±30mm
Cable length 800±30mm
Type 2 outlet
Rubber protection
cover
Battery level
indicator light
Mode
button
AC plug
LCD screen
5
02:00:00
2:00:00 4:00:00 6:00:00 8:00:00
Delay Start
Timer
6
02:00:00 04:00:00 06:00:00 08:00:00
10
Over Temperature
(Control Box)
Wait,
retry charging
Low Voltage Wait,
retry charging
Over Voltage Wait,
retry charging
Over Current Disconnect the
charging plug,
retry charging
Leakage (RCD) Disconnect the
charging plug,
retry charging
Leakage Device
Self Test
Flash light
Float light
Light
Light Light
Disconnect the
charging plug, retry
charging
Component Failure Charger is faulty
Over Temperature
(Input Plug)
Wait for plug
temperature to drop
Error Mode
No. Error State Recovery Method
.0A
10.0A
h
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
2.3 KWh
10.0A 10.0A 10.0A
2.3 KWh 2.3 KWh 2.3 KWh 7.0 KWh
CP Error Wait,
retry charging
Terminal Diode
Failure
9
10
Wait,
retry charging
02:00:00 04:00:00 06:00:00 08:00:00
10
Over Temperature
(Control Box)
Wait,
retry charging
Low Voltage Wait,
retry charging
Over Voltage Wait,
retry charging
Over Current Disconnect the
charging plug,
retry charging
Leakage (RCD) Disconnect the
charging plug,
retry charging
Leakage Device
Self Test
Flash light
Float light
Light
Light Light
Disconnect the
charging plug, retry
charging
Component Failure Charger is faulty
Over Temperature
(Input Plug)
Wait for plug
temperature to drop
Error Mode
No. Error State Recovery Method
.0A
10.0 A
h
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
2.3 KWh
10.0A 10.0A 10.0A
2.3 KWh 2.3 KWh 2.3 KWh 7.0 KWh
CP Error Wait,
retry charging
Terminal Diode
Failure
9
10
Wait,
retry charging
02:00:00 04:00:00 06:00:00 08:00:00
10
Over Temperature
(Control Box)
Wait,
retry charging
Low Voltage Wait,
retry charging
Over Voltage Wait,
retry charging
Over Current Disconnect the
charging plug,
retry charging
Leakage (RCD) Disconnect the
charging plug,
retry charging
Leakage Device
Self Test
Flash light
Float light
Light
Light Light
Disconnect the
charging plug, retry
charging
Component Failure Charger is faulty
Over Temperature
(Input Plug)
Wait for plug
temperature to drop
Error Mode
No. Error State Recovery Method
.0A
10.0 A
h
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
2.3 KWh
10.0A 10.0A 10.0A
2.3 KWh 2.3 KWh 2.3 KWh 7.0 KWh
CP Error Wait,
retry charging
Terminal Diode
Failure
9
10
Wait,
retry charging
02:00:00 04:00:00 06:00:00 08:00:00
10
Over Temperature
(Control Box)
Wait,
retry charging
Low Voltage Wait,
retry charging
Over Voltage Wait,
retry charging
Over Current Disconnect the
charging plug,
retry charging
Leakage (RCD) Disconnect the
charging plug,
retry charging
Leakage Device
Self Test
Flash light
Float light
Light
Light Light
Disconnect the
charging plug, retry
charging
Component Failure Charger is faulty
Over Temperature
(Input Plug)
Wait for plug
temperature to drop
Error Mode
No. Error State Recovery Method
.0A
10.0 A
h
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
2.3 KWh
10.0A 10.0A 10.0A
2.3 KWh 2.3 KWh 2.3 KWh
7.0 KWh
CP Error Wait,
retry charging
Terminal Diode
Failure
9
10
Wait,
retry charging
1. Connect to the AC Mains Power. 2. Set Delay Timer if required.
3. Connect to the car. 4. Charging mode.
7
02:00:00 04:00:00 06:00:00 08:00:00
10
Over Temperature
(Control Box)
Wait,
retry charging
Low Voltage Wait,
retry charging
Over Voltage Wait,
retry charging
Over Current Disconnect the
charging plug,
retry charging
Leakage (RCD) Disconnect the
charging plug,
retry charging
Leakage Device
Self Test
Flash light
Float light
Light
Light Light
Disconnect the
charging plug, retry
charging
Component Failure Charger is faulty
Over Temperature
(Input Plug)
Wait for plug
temperature to drop
Error Mode
No. Error State Recovery Method
.0A
10.0 A
h
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
2.3 KWh
10.0A 10.0A 10.0A
2.3 KWh 2.3 KWh 2.3 KWh 7.0 KWh
CP Error Wait,
retry charging
Terminal Diode
Failure
9
10
Wait,
retry charging
02:00:00 04:00:00 06:00:00 08:00:00
10
Over Temperature
(Control Box)
Wait,
retry charging
Low Voltage Wait,
retry charging
Over Voltage Wait,
retry charging
Over Current Disconnect the
charging plug,
retry charging
Leakage (RCD) Disconnect the
charging plug,
retry charging
Leakage Device
Self Test
Flash light
Float light
Light
Light
Light
Disconnect the
charging plug, retry
charging
Component Failure Charger is faulty
Over Temperature
(Input Plug)
Wait for plug
temperature to drop
Error Mode
No. Error State Recovery Method
.0A
10.0 A
h
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
2.3 KWh
10.0A 10.0A 10.0A
2.3 KWh 2.3 KWh 2.3 KWh
7.0 KWh
CP Error Wait,
retry charging
Terminal Diode
Failure
9
10
Wait,
retry charging
02:00:00 04:00:00 06:00:00 08:00:00
10
Over Temperature
(Control Box)
Wait,
retry charging
Low Voltage Wait,
retry charging
Over Voltage Wait,
retry charging
Over Current Disconnect the
charging plug,
retry charging
Leakage (RCD) Disconnect the
charging plug,
retry charging
Leakage Device
Self Test
Flash light
Float light
Light
Light
Light
Disconnect the
charging plug, retry
charging
Component Failure Charger is faulty
Over Temperature
(Input Plug)
Wait for plug
temperature to drop
Error Mode
No. Error State Recovery Method
.0A
10.0 A
h
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
Delay Start
Timer
2.3 KWh
10.0A 10.0A 10.0A
2.3 KWh 2.3 KWh 2.3 KWh 7.0 KWh
CP Error Wait,
retry charging
Terminal Diode
Failure
9
10
Wait,
retry charging
5. Charging completed. 6. Error mode.
WARRANTY STATEMENT
Brown & Watson International Pty Ltd (“BWI”) of 1500 Ferntree Gully Road, Knoxfield,
Vic., telephone (03) 9730 6000, fax (03) 9730 6050, warrants that all products described in
its current catalogue will under normal use and service be free of failures in material and
workmanship for a period of one (1) year from the date of the original purchase by the
customer as marked on the invoice. This warranty does not cover ordinary wear and tear,
abuse, alteration of products or damage caused by the purchaser.
To make a warranty claim the consumer must deliver the product at their cost to the
original place of purchase or to any other place which may be nominated by either BWI or
the retailer from where the product was bought in order that the warranty assessment may
be performed. The consumer must also deliver the original invoice evidencing the date and
place of purchase together with an explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure of the product then
BWI reserves the right to repair or replace it at its discretion. In the event that a major
failure is determined the consumer will be entitled to a replacement or a refund as well as
compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have
under State or Federal legislation.
IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
IS531
Issue 1 08.03.23
Distributed by
AUSTRALIA
Brown & Watson International Pty. Ltd.
Knoxfield Victoria 3180
Phone: (03) 9730 6000
Fax: (03) 9730 6050
National Toll Free: 1800 113 443
NEW ZEALAND OFFICE
Griffiths Equipment Ltd.
19 Bell Avenue,
Mount Wellington,
Auckland 1060, New Zealand
Phone: (09) 525 4575
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Projecta EVC2KW is a 2.4KW EV emergency charger designed for easy and safe charging of electric vehicles. Featuring a rainproof IP65 design, it ensures reliable operation even in wet conditions. The charger comes with multiple safety protections, including over-voltage, under-voltage, over-current, over-temperature, leakage current, and short-circuit protection, giving you peace of mind during charging.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Projecta EVAPT2T1 Operating instructions
-
Projecta EVAPT1T2 User manual
-
Projecta EVCBT2T2-3P User manual
-
Projecta PMDCS30 User manual
-
Projecta Intelli Grid PMDC-30 DC Charger User manual
-
Projecta INTELLI-RV PM100 User manual
-
Projecta IDC25 User manual
-
Projecta IC3500 User manual
-
Projecta IG2-BT7 User manual
-
Projecta ICBDC User manual
Other documents
-
KT SOLAR KT71201 User manual
-
KT SOLAR KT70703 User manual
-
GRAUPNER ULTRA DUO Plus 80 Owner's manual
-
Fusion EMPEROR L702B User manual
-
Pro-Peak TAURUS O-IP3001 User manual
-
GRAUPNER POLARON EX-1400 Operating Instructions Manual
-
Turnigy T240 Reactor User manual
-
Skyrc Q200neo Charger User manual
-
Horizon PASSPORT Ultra Duo User manual
-
VENOM 2-10 Dual Output DC Multi Charger Owner's manual
