Projecta EVAPT2T1 Operating instructions

EVAPT2T1
Projecta
Brand
Projecta
Model
EVAPT2T1
Type
Operating instructions

Projecta EVAPT2T1: Charge Your Type 1 EV at Type 2 Stations

The Projecta EVAPT2T1 is a handy adaptor that allows you to conveniently charge your Type 1 electric vehicle at Type 2 charging stations. Rated for a current of 32 amps and a voltage of 250 volts AC, it supports fast and efficient charging. Its IP65 ingress protection ensures resistance to dust and water, making it suitable for outdoor use. With a flame-retardant rating of UL94V-0, it prioritizes safety during charging. The compact 0.3-meter cable length provides flexibility while maintaining a tidy setup.

Projecta EVAPT2T1: Charge Your Type 1 EV at Type 2 Stations

The Projecta EVAPT2T1 is a handy adaptor that allows you to conveniently charge your Type 1 electric vehicle at Type 2 charging stations. Rated for a current of 32 amps and a voltage of 250 volts AC, it supports fast and efficient charging. Its IP65 ingress protection ensures resistance to dust and water, making it suitable for outdoor use. With a flame-retardant rating of UL94V-0, it prioritizes safety during charging. The compact 0.3-meter cable length provides flexibility while maintaining a tidy setup.

WARNING
• For charging EV Vehicles only.
• Ifdamageddonotattempttouse.Itmustbereplacedorrepairedbyaqualiedperson.
• This adaptor is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure that they do not play with the appliance.
CARE INSTRUCTIONS
• Try and keep clean, avoid mud and harsh chemicals.
• Clean cable and connector housing with mild detergent and water.
• Apply lubricated contact cleaner to the power terminals regularly.
P/No. EVAPT2T1
EV ADAPTOR
TYPE 2 TO TYPE 1 ADAPTOR
For charging a Type 1 vehicle at a Type 2 charging station.
INSTRUCTIONS FOR USE
1. Connect the adaptor to the charging station.
2. Plug your charging inlet lead to the adaptor.
3. Connect the outlet of the charging lead to the car.
4. To stop charging. Follow the reverse procedure.
SPECIFICATIONS
WARRANTY STATEMENT
Brown&WatsonInternationalPtyLtd(“BWI”)of1500FerntreeGullyRoad,Knoxeld,Vic.,telephone(03)9730
6000,fax(03)97306050,warrantsthatallproductsdescribedinitscurrentcataloguewillundernormaluseand
service be free of failures in material and workmanship for a period of one (1) year from the date of the original
purchase by the customer as marked on the invoice. This warranty does not cover ordinary wear and tear, abuse,
alteration of products or damage caused by the purchaser.
To make a warranty claim the consumer must deliver the product at their cost to the original place of purchase
or to any other place which may be nominated by either BWI or the retailer from where the product was bought
in order that the warranty assessment may be performed. The consumer must also deliver the original invoice
evidencing the date and place of purchase together with an explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure of the product then BWI reserves the right to
repair or replace it at its discretion. In the event that a major failure is determined the consumer will be entitled to
a replacement or a refund as well as compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have under State or Federal
legislation.
IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Distributed by
AUSTRALIA
Brown & Watson International Pty. Ltd.
KnoxeldVictoria3180
Phone:(03)97306000
Fax:(03)97306050
NationalTollFree:1800113443
PART NO. EVAPT2T1
RATED CURRENT 32A Max
RATED VOLTAGE 250V AC
INGRESS PROTECTION IP65
VOLTAGE WITHSTAND 2000V AC 5S
FLAME-RETARDANT UL94V-0
CABLE LENGTH 0.3m
WORKING TEMPERATURE -30°C ~ +50°C
NEW ZEALAND OFFICE
Grifths Equipment Ltd.
19BellAvenue,
Mount Wellington,
Auckland 1060, New Zealand
Phone:(09)5254575
IS532
Issue 1 3.3.23
T2 INLET
Socket Side
T1 OUTLET
Vehicle Side
  • Page 1 1
  • Page 2 2

Projecta EVAPT2T1 Operating instructions

EVAPT2T1
Projecta
Brand
Projecta
Model
EVAPT2T1
Type
Operating instructions

Projecta EVAPT2T1: Charge Your Type 1 EV at Type 2 Stations

The Projecta EVAPT2T1 is a handy adaptor that allows you to conveniently charge your Type 1 electric vehicle at Type 2 charging stations. Rated for a current of 32 amps and a voltage of 250 volts AC, it supports fast and efficient charging. Its IP65 ingress protection ensures resistance to dust and water, making it suitable for outdoor use. With a flame-retardant rating of UL94V-0, it prioritizes safety during charging. The compact 0.3-meter cable length provides flexibility while maintaining a tidy setup.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents