Projecta EVCBT2T2-3P User manual

EVCBT2T2-3P
Projecta
Brand
Projecta
Model
EVCBT2T2-3P
Type
User manual

Projecta EVCBT2T2-3P is a charging cable designed for electric vehicles, specifically Type 2 vehicles and chargers. It supports a wide range of power, from 7.2kW to 22kW, and operates on a 3-phase system. The cable is IP65 rated, making it resistant to dust and water, and has an IK10 impact protection rating, ensuring durability. It can withstand a wide range of temperatures, from -25°C to +45°C, and humidity levels from 5% to 95%. The cable is 5 meters long, with a cable length of 4.6 meters, and weighs 3.39 kilograms.

Projecta EVCBT2T2-3P is a charging cable designed for electric vehicles, specifically Type 2 vehicles and chargers. It supports a wide range of power, from 7.2kW to 22kW, and operates on a 3-phase system. The cable is IP65 rated, making it resistant to dust and water, and has an IK10 impact protection rating, ensuring durability. It can withstand a wide range of temperatures, from -25°C to +45°C, and humidity levels from 5% to 95%. The cable is 5 meters long, with a cable length of 4.6 meters, and weighs 3.39 kilograms.

vvavt
WARNING
• For charging EV Vehicles only.
• If cord is damaged do not attempt to use. It must be replaced or repaired by a
 qualiedperson.
• This lead is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
• Children should be supervised to ensure that they do not play with the appliance.
CARE INSTRUCTIONS
• Try and keep clean, avoid mud and harsh chemicals.
• Clean cable and connector housing with mild detergent and water.
• Apply lubricated contact cleaner to the power terminals regularly.
EV CHARGING CABLE
TYPE 2 TO TYPE 2 7.2KW ~ 22KW 3 PHASE
P/No. EVCBT2T2-3P
INSTRUCTIONS FOR USE
The charge cable is suitable for Type 2 7.2~22KW vehicles and chargers.
1. Connect the inlet of the charging lead into the charger.
2. Connect the outlet of the charging lead to the car.
3. To stop charging. Follow the reverse procedure.
SPECIFICATIONS
WARRANTY STATEMENT
Brown&WatsonInternationalPtyLtd(“BWI”)of1500FerntreeGullyRoad,Knoxeld,Vic.,telephone(03)9730
6000,fax(03)97306050,warrantsthatallproductsdescribedinitscurrentcataloguewillundernormaluseand
service be free of failures in material and workmanship for a period of one (1) year from the date of the original
purchase by the customer as marked on the invoice. This warranty does not cover ordinary wear and tear, abuse,
alteration of products or damage caused by the purchaser.
To make a warranty claim the consumer must deliver the product at their cost to the original place of purchase
or to any other place which may be nominated by either BWI or the retailer from where the product was bought
in order that the warranty assessment may be performed. The consumer must also deliver the original invoice
evidencing the date and place of purchase together with an explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure of the product then BWI reserves the right to
repair or replace it at its discretion. In the event that a major failure is determined the consumer will be entitled to
a replacement or a refund as well as compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the consumer may have under State or Federal
legislation.
IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Distributed by
AUSTRALIA
Brown & Watson International Pty. Ltd.
KnoxeldVictoria3180
Phone:(03)97306000
Fax:(03)97306050
NationalTollFree:1800113443
PART NO. EVCBT2T2-3P
PHASE 3
VOLTAGE 400V
CURRENT 32A
MAX POWER 22kWh
OVERALL LENGTH 5m
CABLE LENGTH 4.6m
WEIGHT 3.39kg
NEW ZEALAND OFFICE
Grifths Equipment Ltd.
19BellAvenue,
Mount Wellington,
Auckland 1060, New Zealand
Phone:(09)5254575
IS536
Issue 1 3.3.23
IP RATING IP65
IMPACT PROTECTION IK10
WORKING TEMPERATURE -25°C~+45°C
WORKING HUMIDITY 5~95%
BATTERY CHARGE TIMES
30kWh BATTERY 1.5 hrs
60kWh BATTERY 3 hrs
90kWhBATTERY 4.5hrs
  • Page 1 1
  • Page 2 2

Projecta EVCBT2T2-3P User manual

EVCBT2T2-3P
Projecta
Brand
Projecta
Model
EVCBT2T2-3P
Type
User manual

Projecta EVCBT2T2-3P is a charging cable designed for electric vehicles, specifically Type 2 vehicles and chargers. It supports a wide range of power, from 7.2kW to 22kW, and operates on a 3-phase system. The cable is IP65 rated, making it resistant to dust and water, and has an IK10 impact protection rating, ensuring durability. It can withstand a wide range of temperatures, from -25°C to +45°C, and humidity levels from 5% to 95%. The cable is 5 meters long, with a cable length of 4.6 meters, and weighs 3.39 kilograms.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents