Fujitsu PRIMERGY RX200 S7 User manual

Upgrade and Maintenance Manual - English

PRIMERGY RX200 S7

Server

Upgrade and Maintenance Manual

Edition October 2013

Comments…Suggestions…Corrections…

The User Documentation Department would like to

know your opinion of this manual. Your feedback helps

us optimize our documentation to suit your individual

needs.

Feel free to send us your comments by e-mail to

[email protected].

Certified documentation

according to DIN EN ISO 9001:2008

To ensure a consistently high quality standard and

user-friendliness, this documentation was created to

meet the regulations of a quality management system

which complies with the requirements of the standard

DIN EN ISO 9001:2008.

cognitas. Gesellschaft für Technik-Dokumentation mbH

www.cognitas.de

Copyright and Trademarks

Delivery subject to availability; right of technical modifications reserved.

All hardware and software names used are trademarks of their respective manufacturers.

– The contents of this manual may be revised without prior notice.

– Fujitsu assumes no liability for damages to third party copyrights or other rights arising from

the use of any information in this manual.

– No part of this manual may be reproduced in any form without the prior written permission

of Fujitsu.

Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of

Microsoft Corporation in the USA and other countries.

Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries

in the USA and other countries.

RX200 S7

Upgrade and Maintenance Manual

Before reading this manual

For your safety

This manual contains important information for safely and correctly using this

product.

Carefully read the manual before using this product. Pay particular attention to

the accompanying manual "Safety Notes and Regulations" and ensure these

safety notes are understood before using the product. Keep this manual and the

manual "Safety Notes and Regulations" in a safe place for easy reference while

using this product.

Radio interference

This product is a "Class A" ITE (Information Technology Equipment). In a

domestic environment this product may cause radio interference, in which case

the user may be required to take appropriate measures. VCCI-A

Aluminum electrolytic capacitors

The aluminum electrolytic capacitors used in the product's printed circuit board

assemblies and in the mouse and keyboard are limited-life components. Use of

these components beyond their operating life may result in electrolyte leakage

or depletion, potentially causing emission of foul odor or smoke.

As a guideline, in a normal office environment (25°C) operating life is not

expected to be reached within the maintenance support period (5 years).

However, operating life may be reached more quickly if, for example, the

product is used in a hot environment. The customer shall bear the cost of

replacing replaceable components which have exceeded their operating life.

Note that these are only guidelines, and do not constitute a guarantee of

trouble-free operation during the maintenance support period.

High safety use

This product has been designed and manufactured to be used in commercial

and/or industrial areas as a server.

When used as visual display workplace, it must not be placed in the direct field

of view to avoid incommoding reflections (applies only to TX server systems).

The device has not been designed or manufactured for uses which demand an

extremely high level of safety and carry a direct and serious risk of life or body

if such safety cannot be assured.

Upgrade and Maintenance Manual

RX200 S7

These uses include control of nuclear reactions in nuclear power plants,

automatic airplane flight control, air traffic control, traffic control in mass

transport systems, medical devices for life support, and missile guidance

control in weapons systems (hereafter, "high safety use"). Customers should

not use this product for high safety use unless measures are in place for

ensuring the level of safety demanded of such use. Please consult the sales

staff of Fujitsu if intending to use this product for high safety use.

Measures against momentary voltage drop

This product may be affected by a momentary voltage drop in the power supply

caused by lightning. To prevent a momentary voltage drop, use of an AC

uninterruptible power supply is recommended.

(This notice follows the guidelines of Voltage Dip Immunity of Personal

Computer issued by JEITA, the Japan Electronics and Information Technology

Industries Association.)

Technology controlled by the Foreign Exchange and Foreign Trade

Control Law of Japan

Documents produced by Fujitsu may contain technology controlled by the

Foreign Exchange and Foreign Trade Control Law of Japan. Documents which

contain such technology should not be exported from Japan or transferred to

non-residents of Japan without first obtaining authorization in accordance with

the above law.

Harmonic Current Standards

This product conforms to harmonic current standard JIS C 61000-3-2.

Only for the Japanese market:

About SATA hard disk drives

The SATA version of this server supports hard disk drives with SATA / BC-SATA

storage interfaces. Please note that the usage and operation conditions differ

depending on the type of hard disk drive used.

Please refer to the following internet address for further information on the

usage and operation conditions of each available type of hard disk drive:

http://jp.fujitsu.com/platform/server/primergy/harddisk/

RX200 S7

Upgrade and Maintenance Manual

Only for the Japanese market:

IAlthough described in this manual, some sections do not apply to the

Japanese market. These options and routines include:

– CSS (Customer Self Service)

Upgrade and Maintenance Manual

RX200 S7

Upgrade and Maintenance Manual

Version history

Issue number Reason for update

1.0 / March 2012 Initial release

2.0 / June 2012 Notes for new hardware added

3.0 / December 2012 Added fan test procedure, changed photos of SFP+

transceiver modules

4.0 / October 2013 Deleted ENERGY STAR, updated fan test procedure

Upgrade and Maintenance Manual

RX200 S7

V

ersion history

RX200 S7

Upgrade and Maintenance Manual

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

1.1 Where to find which information? . . . . . . . . . . . . . . . 26

1.2 Notational conventions . . . . . . . . . . . . . . . . . . . . 27

2 Before you start . . . . . . . . . . . . . . . . . . . . . . . . 29

2.1 Classification of procedures . . . . . . . . . . . . . . . . . 31

2.1.1 Customer Replaceable Units (CRU) . . . . . . . . . . . . . . . 31

2.1.2 Upgrade and Repair Units (URU) . . . . . . . . . . . . . . . . 32

2.1.3 Field Replaceable Units (FRU) . . . . . . . . . . . . . . . . . 33

2.2 Average task duration . . . . . . . . . . . . . . . . . . . . . 34

2.3 Tools you need at hand . . . . . . . . . . . . . . . . . . . . 35

2.4 Documents you need at hand . . . . . . . . . . . . . . . . . 36

3 Important information . . . . . . . . . . . . . . . . . . . . . 39

3.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 39

3.2 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 47

3.3 FCC Class A Compliance Statement . . . . . . . . . . . . . 47

3.4 Environmental protection . . . . . . . . . . . . . . . . . . . 48

4 Basic hardware procedures . . . . . . . . . . . . . . . . . . 51

4.1 Using diagnostics information . . . . . . . . . . . . . . . . 51

4.1.1 Locating the defective server . . . . . . . . . . . . . . . . . . 51

4.1.2 Determining the error class . . . . . . . . . . . . . . . . . . . 52

4.1.2.1 Global Error indicator . . . . . . . . . . . . . . . . . . . . 52

4.1.2.2 Customer Self Service (CSS) indicator . . . . . . . . . . . 53

4.1.3 Locating the defective component . . . . . . . . . . . . . . . . 54

4.1.3.1 Local diagnostic indicators on the system board . . . . . . . 54

4.2 Opening the rack door . . . . . . . . . . . . . . . . . . . . . 55

Upgrade and Maintenance Manual

RX200 S7

Contents

4.3 Shutting down the server . . . . . . . . . . . . . . . . . . . . 55

4.4 Extending/removing the server from the rack . . . . . . . . . 56

4.4.1 Disconnecting the power cord . . . . . . . . . . . . . . . . . . 56

4.4.2 Extending the server out of the rack . . . . . . . . . . . . . . . 57

4.4.3 Removing the server from the telescopic rails . . . . . . . . . . 58

4.5 Opening the server . . . . . . . . . . . . . . . . . . . . . . . 59

4.5.1 Removing the fan cover . . . . . . . . . . . . . . . . . . . . . . 59

4.5.2 Removing the housing cover . . . . . . . . . . . . . . . . . . . 60

4.6 Removing riser modules . . . . . . . . . . . . . . . . . . . . 61

4.6.1 Removing the riser module 1 . . . . . . . . . . . . . . . . . . . 61

4.6.2 Removing the riser module 2 . . . . . . . . . . . . . . . . . . . 61

4.6.3 Removing the riser module 3 . . . . . . . . . . . . . . . . . . . 62

4.7 Removing the air duct . . . . . . . . . . . . . . . . . . . . . . 63

4.8 Installing the air duct . . . . . . . . . . . . . . . . . . . . . . 63

4.9 Installing riser modules . . . . . . . . . . . . . . . . . . . . . 64

4.9.1 Installing the riser module 1 . . . . . . . . . . . . . . . . . . . . 64

4.9.2 Installing the riser module 2 . . . . . . . . . . . . . . . . . . . . 65

4.9.3 Installing the riser module 3 . . . . . . . . . . . . . . . . . . . . 66

4.10 Closing the server . . . . . . . . . . . . . . . . . . . . . . . . 67

4.10.1 Installing the housing cover . . . . . . . . . . . . . . . . . . . . 67

4.10.2 Installing the fan cover . . . . . . . . . . . . . . . . . . . . . . 68

4.11 Installing the server in the rack . . . . . . . . . . . . . . . . . 69

4.11.1 Inserting the server into the telescopic rails . . . . . . . . . . . 69

4.11.2 Sliding the server into the rack . . . . . . . . . . . . . . . . . . 71

4.11.3 Connecting the power cord . . . . . . . . . . . . . . . . . . . . 72

4.12 Switching on the server . . . . . . . . . . . . . . . . . . . . . 73

4.13 Concluding software tasks . . . . . . . . . . . . . . . . . . . 73

4.14 Closing the rack door . . . . . . . . . . . . . . . . . . . . . . 74

5 Basic software procedures . . . . . . . . . . . . . . . . . . . 75

5.1 Starting the maintenance task . . . . . . . . . . . . . . . . . 75

5.1.1 Disabling BitLocker functionality . . . . . . . . . . . . . . . . . 75

5.1.2 Disabling SVOM boot watchdog functionality . . . . . . . . . . . 76

5.1.2.1 Viewing boot watchdog settings . . . . . . . . . . . . . . . . 76

5.1.2.2 Configuring boot watchdog settings . . . . . . . . . . . . . . 76

RX200 S7

Upgrade and Maintenance Manual

Contents

5.1.3 Removing backup and optical disk media . . . . . . . . . . . . 77

5.1.4 Verifying and configuring the backup software solution . . . . . 78

5.1.5 Note on server maintenance in a Multipath I/O environment . . 78

5.1.6 Switching on the ID indicator . . . . . . . . . . . . . . . . . . 80

5.2 Completing the maintenance task . . . . . . . . . . . . . . . 81

5.2.1 Updating the system board BIOS and iRMC . . . . . . . . . . 81

5.2.2 Verifying system information backup / restore . . . . . . . . . . 83

5.2.3 Updating RAID controller firmware . . . . . . . . . . . . . . . 84

5.2.4 Enabling Option ROM scan . . . . . . . . . . . . . . . . . . . 85

5.2.5 Verifying and configuring the backup software solution . . . . . 86

5.2.6 Resetting the boot retry counter . . . . . . . . . . . . . . . . . 86

5.2.6.1 Viewing the boot retry counter . . . . . . . . . . . . . . . . 87

5.2.6.2 Resetting the boot retry counter . . . . . . . . . . . . . . . 87

5.2.7 Enabling SVOM boot watchdog functionality . . . . . . . . . . 88

5.2.8 Enabling replaced components in the system BIOS . . . . . . . 89

5.2.9 Verifying the memory mode . . . . . . . . . . . . . . . . . . . 90

5.2.10 Verifying the system time settings . . . . . . . . . . . . . . . . 90

5.2.11 Viewing and clearing the System Event Log (SEL) . . . . . . . 91

5.2.11.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . 91

5.2.11.2 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . . 92

5.2.12 Updating the NIC configuration file in a Linux environment . . . 92

5.2.13 Enabling BitLocker functionality . . . . . . . . . . . . . . . . . 94

5.2.14 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 95

5.2.15 Looking up changed MAC / WWN addresses . . . . . . . . . . 95

5.2.15.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . 95

5.2.15.2 Looking up WWN addresses . . . . . . . . . . . . . . . . . 96

5.2.16 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 97

5.2.17 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . 97

5.2.17.1 After replacing / upgrading LAN controllers . . . . . . . . . 98

5.2.17.2 After replacing the system board . . . . . . . . . . . . . . . 98

5.2.18 Switching off the ID indicator . . . . . . . . . . . . . . . . . . 98

5.2.19 Performing a fan test after replacing a defective fan . . . . . . 99

6 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . 101

6.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 101

6.1.1 General equipping rules . . . . . . . . . . . . . . . . . . . . . 101

6.2 Installing a power supply module . . . . . . . . . . . . . . . 102

6.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 102

6.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 102

Upgrade and Maintenance Manual

RX200 S7

Contents

6.2.3 Removing the dummy cover . . . . . . . . . . . . . . . . . . 102

6.2.4 Installing the power supply module . . . . . . . . . . . . . . . 103

6.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 105

6.3 Removing a power supply module . . . . . . . . . . . . . . 105

6.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 107

6.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 107

6.3.3 Removing the power supply module . . . . . . . . . . . . . . 107

6.3.4 Installing the dummy cover . . . . . . . . . . . . . . . . . . . 108

6.3.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 108

6.4 Replacing a power supply module . . . . . . . . . . . . . . 109

6.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 109

6.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 110

6.4.3 Removing the defective power supply module . . . . . . . . . 110

6.4.4 Installing the new power supply module . . . . . . . . . . . . 110

6.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 110

6.5 Replacing the power distribution board . . . . . . . . . . . 111

6.5.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 111

6.5.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 111

6.5.3 Removing the defective power distribution board . . . . . . . . 112

6.5.4 Installing the new power distribution board . . . . . . . . . . . 113

6.5.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 115

7 Hard disk drives / solid state drives . . . . . . . . . . . . . 117

7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 118

7.1.1 General equipping rules . . . . . . . . . . . . . . . . . . . . 118

7.1.2 Configuration with up to four HDD/SSD modules . . . . . . . . 119

7.1.3 Configuration with up to eight HDD/SSD modules . . . . . . . 119

7.2 Installing a 2.5-inch HDD/SSD module . . . . . . . . . . . . 120

7.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 120

7.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 121

7.2.3 Removing the 2.5-inch dummy module . . . . . . . . . . . . . 121

7.2.4 Installing the 2.5-inch HDD/SSD module . . . . . . . . . . . . 122

7.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 123

7.3 Removing a 2.5-inch HDD/SSD module . . . . . . . . . . . 123

7.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 123

7.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 123

7.3.3 Removing the 2.5-inch HDD/SSD module . . . . . . . . . . . 124

7.3.4 Installing the 2.5-inch dummy module . . . . . . . . . . . . . 125

RX200 S7

Upgrade and Maintenance Manual

Contents

7.3.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 125

7.4 Replacing a 2.5-inch HDD/SSD module . . . . . . . . . . . . 126

7.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 126

7.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 127

7.4.3 Removing the defective 2.5-inch HDD/SSD module . . . . . . 127

7.4.4 Installing the new 2.5-inch HDD/SSD module . . . . . . . . . . 127

7.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 127

7.5 Replacing the 4xHDD backplane . . . . . . . . . . . . . . . 128

7.5.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 129

7.5.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 129

7.5.3 Removing the defective 4xHDD backplane . . . . . . . . . . . 129

7.5.4 Installing the new 4xHDD backplane . . . . . . . . . . . . . . 131

7.5.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 132

7.6 Replacing the 8xHDD backplane . . . . . . . . . . . . . . . 133

7.6.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 133

7.6.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 133

7.6.3 Removing the defective 8xHDD backplane . . . . . . . . . . . 133

7.6.4 Installing the new 8xHDD backplane . . . . . . . . . . . . . . 136

7.6.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 138

7.7 Converting to configuration up to eight HDD/SSD modules 139

7.7.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 139

7.7.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 139

7.7.3 Removing the 4xHDD backplane . . . . . . . . . . . . . . . . 139

7.7.4 Removing the ODD cable and ODD cage . . . . . . . . . . . . 140

7.7.5 Installing the 2xHDD cage . . . . . . . . . . . . . . . . . . . . 142

7.7.6 Installing the 8xHDD backplane . . . . . . . . . . . . . . . . . 142

7.7.7 Installing the HDD/SSD modules . . . . . . . . . . . . . . . . 143

7.7.8 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 143

8 Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

8.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 146

8.2 Replacing a fan module . . . . . . . . . . . . . . . . . . . . 147

8.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 147

8.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 147

8.2.3 Removing the defective fan module . . . . . . . . . . . . . . . 148

8.2.4 Installing the new fan module . . . . . . . . . . . . . . . . . . 148

8.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 149

Upgrade and Maintenance Manual

RX200 S7

Contents

9 Expansion cards and backup units . . . . . . . . . . . . . 151

9.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 152

9.1.1 Equipping the PCIe slots . . . . . . . . . . . . . . . . . . . . 153

9.2 Additional tasks . . . . . . . . . . . . . . . . . . . . . . . . 157

9.2.1 Installing expansion card slot brackets . . . . . . . . . . . . . 157

9.2.1.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 157

9.2.1.2 Installing an expansion card slot bracket . . . . . . . . . . 157

9.2.2 Installing SFP+ transceiver modules . . . . . . . . . . . . . . 164

9.2.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 164

9.2.2.2 Installing the first SFP+ transceiver module . . . . . . . . . 164

9.2.2.3 Installing the second SFP+ transceiver module . . . . . . . 167

9.2.3 Removing expansion card slot brackets . . . . . . . . . . . . 167

9.2.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 167

9.2.3.2 Removing an expansion card slot bracket . . . . . . . . . 167

9.2.4 Replacing SFP+ transceiver modules . . . . . . . . . . . . . 168

9.2.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 168

9.2.4.2 Removing the SFP+ transceiver module . . . . . . . . . . 168

9.2.4.3 Installing the SFP+ transceiver module . . . . . . . . . . . 169

9.3 Expansion cards and riser cards . . . . . . . . . . . . . . . 170

9.3.1 Installing an expansion card in riser module 1 . . . . . . . . . 170

9.3.1.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 170

9.3.1.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 171

9.3.1.3 Removing the slot cover - slot 1 . . . . . . . . . . . . . . . 171

9.3.1.4 Installing the expansion card - slot 1 . . . . . . . . . . . . 172

9.3.1.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 172

9.3.2 Installing an expansion card in riser module 2 . . . . . . . . . 173

9.3.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 173

9.3.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 173

9.3.2.3 Removing the slot cover - slot 2 and slot 3 . . . . . . . . . 174

9.3.2.4 Installing the expansion card - slot 2 and slot 3 . . . . . . . 175

9.3.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 177

9.3.3 Installing an expansion card in riser module 3 . . . . . . . . . 177

9.3.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 177

9.3.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 178

9.3.3.3 Installing the expansion card - slot 4 . . . . . . . . . . . . 178

9.3.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 179

9.3.4 Removing an expansion card in riser module 1 . . . . . . . . 180

9.3.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 180

9.3.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 180

9.3.4.3 Removing the expansion card - slot 1 . . . . . . . . . . . . 181

RX200 S7

Upgrade and Maintenance Manual

Contents

9.3.4.4 Installing the slot cover - slot 1 . . . . . . . . . . . . . . . . 182

9.3.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 182

9.3.5 Removing an expansion card in riser module 2 . . . . . . . . . 183

9.3.5.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 183

9.3.5.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 183

9.3.5.3 Removing the expansion card- slot 2 and slot 3 . . . . . . . 184

9.3.5.4 Installing the slot cover - slot 2 and slot 3 . . . . . . . . . . 185

9.3.5.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 185

9.3.6 Removing an expansion card in riser module 3 . . . . . . . . . 186

9.3.6.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 186

9.3.6.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 186

9.3.6.3 Removing the expansion card - slot 4 . . . . . . . . . . . . 187

9.3.6.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 187

9.3.7 Replacing an expansion card in riser module 1 . . . . . . . . . 188

9.3.7.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 188

9.3.7.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 188

9.3.7.3 Removing the defective expansion card . . . . . . . . . . . 189

9.3.7.4 Installing the new expansion card . . . . . . . . . . . . . . 189

9.3.7.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 189

9.3.8 Replacing an expansion card in riser module 2 . . . . . . . . . 190

9.3.8.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 190

9.3.8.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 191

9.3.8.3 Removing the defective expansion card . . . . . . . . . . . 191

9.3.8.4 Installing the new expansion card . . . . . . . . . . . . . . 191

9.3.8.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 191

9.3.9 Replacing an expansion card in riser module 3 . . . . . . . . . 192

9.3.9.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 193

9.3.9.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 193

9.3.9.3 Removing the defective expansion card . . . . . . . . . . . 193

9.3.9.4 Installing the new expansion card . . . . . . . . . . . . . . 193

9.3.9.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 194

9.3.10 Replacing the riser card in riser module 1 . . . . . . . . . . . . 195

9.3.10.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 195

9.3.10.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 195

9.3.10.3 Removing the defective riser card . . . . . . . . . . . . . . 195

9.3.10.4 Installing the new riser card . . . . . . . . . . . . . . . . . 196

9.3.10.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 197

9.3.11 Replacing the riser card in riser module 2 . . . . . . . . . . . . 197

9.3.11.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 197

9.3.11.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 197

9.3.11.3 Removing the defective riser card . . . . . . . . . . . . . . 198

9.3.11.4 Installing the new riser card . . . . . . . . . . . . . . . . . 199

Upgrade and Maintenance Manual

RX200 S7

Contents

9.3.11.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 199

9.3.12 Replacing the riser card in riser module 3 . . . . . . . . . . . 200

9.3.12.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 200

9.3.12.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 200

9.3.12.3 Removing the defective riser card . . . . . . . . . . . . . . 201

9.3.12.4 Installing the new riser card . . . . . . . . . . . . . . . . . 202

9.3.12.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 202

9.3.13 Replacing TFM . . . . . . . . . . . . . . . . . . . . . . . . . 203

9.3.13.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 203

9.3.13.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 203

9.3.13.3 Removing the defective TFM . . . . . . . . . . . . . . . . 203

9.3.13.4 Installing the new TFM . . . . . . . . . . . . . . . . . . . 204

9.3.13.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 204

9.4 Backup units (BBU/FBU) . . . . . . . . . . . . . . . . . . . 205

9.4.1 Installing the BBU . . . . . . . . . . . . . . . . . . . . . . . . 205

9.4.1.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 205

9.4.1.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 205

9.4.1.3 Connecting the BBU cable to the BBU . . . . . . . . . . . 206

9.4.1.4 Installing the BBU in the holder . . . . . . . . . . . . . . . 207

9.4.1.5 Installing the BBU with the holder . . . . . . . . . . . . . . 208

9.4.1.6 Connecting the BBU cable to the RAID controller . . . . . . 209

9.4.1.7 Routing the BBU cable . . . . . . . . . . . . . . . . . . . 210

9.4.1.8 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 211

9.4.2 Installing the FBU . . . . . . . . . . . . . . . . . . . . . . . . 212

9.4.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 212

9.4.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 212

9.4.2.3 Installing the FBU in the holder . . . . . . . . . . . . . . . 213

9.4.2.4 Connecting the FBU cable to the FBU . . . . . . . . . . . 214

9.4.2.5 Installing the FBU with the holder . . . . . . . . . . . . . . 215

9.4.2.6 Installing TFM to the RAID controller (if applicable) . . . . . 216

9.4.2.7 Connecting the FBU cable to the RAID controller . . . . . . 217

9.4.2.8 Routing the FBU cable . . . . . . . . . . . . . . . . . . . 217

9.4.2.9 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 218

9.4.3 Removing the BBU . . . . . . . . . . . . . . . . . . . . . . . 219

9.4.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 219

9.4.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 219

9.4.3.3 Disconnecting the BBU cable from the RAID controller . . . 220

9.4.3.4 Removing the BBU with the holder . . . . . . . . . . . . . 221

9.4.3.5 Removing the BBU from the holder . . . . . . . . . . . . . 222

9.4.3.6 Disconnecting the BBU cable from the BBU . . . . . . . . 222

9.4.3.7 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 223

RX200 S7

Upgrade and Maintenance Manual

Contents

9.4.4 Removing the FBU . . . . . . . . . . . . . . . . . . . . . . . 223

9.4.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 223

9.4.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 224

9.4.4.3 Disconnecting the FBU cable from the RAID controller . . . 224

9.4.4.4 Removing the FBU with the holder . . . . . . . . . . . . . . 225

9.4.4.5 Disconnecting the FBU cable from the FBU . . . . . . . . . 226

9.4.4.6 Removing the FBU from the holder . . . . . . . . . . . . . 227

9.4.4.7 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 227

9.4.5 Replacing the BBU . . . . . . . . . . . . . . . . . . . . . . . 228

9.4.5.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 228

9.4.5.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 228

9.4.5.3 Removing the defective BBU . . . . . . . . . . . . . . . . 229

9.4.5.4 Installing the new BBU . . . . . . . . . . . . . . . . . . . . 229

9.4.5.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 229

9.4.6 Replacing the FBU . . . . . . . . . . . . . . . . . . . . . . . . 230

9.4.6.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . 231

9.4.6.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 231

9.4.6.3 Removing the defective FBU . . . . . . . . . . . . . . . . . 231

9.4.6.4 Installing the new FBU . . . . . . . . . . . . . . . . . . . . 231

9.4.6.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 232

10 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . . 233

10.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 234

10.1.1 Memory sequence . . . . . . . . . . . . . . . . . . . . . . . . 236

10.1.1.1 Population rules . . . . . . . . . . . . . . . . . . . . . . . 236

10.1.1.2 Independant Channel mode . . . . . . . . . . . . . . . . . 237

10.1.1.3 Mirrored Channel and Performance modes . . . . . . . . . 238

10.1.1.4 Rank Sparing mode . . . . . . . . . . . . . . . . . . . . . 239

10.2 Installing a memory module . . . . . . . . . . . . . . . . . . 244

10.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 244

10.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 244

10.2.3 Selecting the memory slot . . . . . . . . . . . . . . . . . . . . 244

10.2.4 Installing a memory module . . . . . . . . . . . . . . . . . . . 245

10.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 245

10.3 Removing a memory module . . . . . . . . . . . . . . . . . 246

10.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 246

10.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 246

10.3.3 Removing a memory module . . . . . . . . . . . . . . . . . . 247

10.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 247

Upgrade and Maintenance Manual

RX200 S7

Contents

10.4 Replacing a memory module . . . . . . . . . . . . . . . . . 248

10.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 248

10.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 248

10.4.3 Removing the defective memory module . . . . . . . . . . . . 248

10.4.4 Installing the new memory module . . . . . . . . . . . . . . . 249

10.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 249

11 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 251

11.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 252

11.1.1 Supported processors . . . . . . . . . . . . . . . . . . . . . 252

11.1.2 General equipping rules . . . . . . . . . . . . . . . . . . . . 252

11.2 Upgrading to dual processor configuration . . . . . . . . . 253

11.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 253

11.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 254

11.2.3 Installing the processor . . . . . . . . . . . . . . . . . . . . . 254

11.2.4 Installing the heat sink . . . . . . . . . . . . . . . . . . . . . 260

11.2.5 Upgrading the main memory . . . . . . . . . . . . . . . . . . 262

11.2.6 Installing two additional fan modules . . . . . . . . . . . . . . 262

11.2.7 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 263

11.3 Replacing a processor . . . . . . . . . . . . . . . . . . . . 264

11.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 264

11.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 264

11.3.3 Removing the heat sink . . . . . . . . . . . . . . . . . . . . . 265

11.3.4 Cleaning the heat sink underside and the processor surface . . 266

11.3.5 Removing the defective processor . . . . . . . . . . . . . . . 266

11.3.6 Installing the new processor . . . . . . . . . . . . . . . . . . 270

11.3.7 Applying the thermal paste to the processor surface . . . . . . 272

11.3.8 Installing the heat sink . . . . . . . . . . . . . . . . . . . . . 275

11.3.9 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 276

11.4 Replacing a heat sink . . . . . . . . . . . . . . . . . . . . . 277

11.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 277

11.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 277

11.4.3 Removing the defective heat sink . . . . . . . . . . . . . . . . 277

11.4.4 Cleaning the processor surface . . . . . . . . . . . . . . . . . 277

11.4.5 Installing the new heat sink . . . . . . . . . . . . . . . . . . . 278

11.4.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 278

RX200 S7

Upgrade and Maintenance Manual

Contents

12 Optical disk drive . . . . . . . . . . . . . . . . . . . . . . . . 279

12.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 280

12.2 Installing the ODD . . . . . . . . . . . . . . . . . . . . . . . 280

12.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 280

12.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 280

12.2.3 Removing the dummy module . . . . . . . . . . . . . . . . . . 281

12.2.4 Installing the ODD . . . . . . . . . . . . . . . . . . . . . . . . 282

12.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 283

12.3 Removing the ODD . . . . . . . . . . . . . . . . . . . . . . . 284

12.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 284

12.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 284

12.3.3 Removing the ODD . . . . . . . . . . . . . . . . . . . . . . . 285

12.3.4 Installing the dummy module . . . . . . . . . . . . . . . . . . 287

12.3.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 288

12.4 Replacing the ODD . . . . . . . . . . . . . . . . . . . . . . . 288

12.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 288

12.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 288

12.4.3 Removing the defective ODD . . . . . . . . . . . . . . . . . . 289

12.4.4 Installing the new ODD . . . . . . . . . . . . . . . . . . . . . 289

12.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 289

13 Front panel and front VGA/LAN module . . . . . . . . . . . 291

13.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 291

13.2 Installing the front VGA and/or front LAN . . . . . . . . . . 292

13.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . . 292

13.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 292

13.2.3 Removing the front VGA/LAN module . . . . . . . . . . . . . . 293

13.2.4 Removing the covers . . . . . . . . . . . . . . . . . . . . . . 294

13.2.5 Installing the front VGA connector . . . . . . . . . . . . . . . . 294

13.2.6 Installing the front LAN connector . . . . . . . . . . . . . . . . 295

13.2.7 Installing the front VGA/LAN module . . . . . . . . . . . . . . 298

13.2.8 Connecting the front VGA cable . . . . . . . . . . . . . . . . . 299

13.2.9 Connecting the front LAN cable . . . . . . . . . . . . . . . . . 299

13.2.10 Installing the front LAN card . . . . . . . . . . . . . . . . . . . 300

13.2.11 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 300

13.2.12 Using the front management LAN connector . . . . . . . . . . 301

Upgrade and Maintenance Manual

RX200 S7

Contents

13.3 Removing the front VGA and/or front LAN . . . . . . . . . 302

13.3.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 302

13.3.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 302

13.3.3 Removing the front LAN card . . . . . . . . . . . . . . . . . . 303

13.3.4 Disconnecting the front LAN cable . . . . . . . . . . . . . . . 303

13.3.5 Disconnecting the front VGA cable . . . . . . . . . . . . . . . 304

13.3.6 Removing the front VGA/LAN module . . . . . . . . . . . . . 304

13.3.7 Removing the front LAN connector . . . . . . . . . . . . . . . 305

13.3.8 Removing the front VGA connector . . . . . . . . . . . . . . . 307

13.3.9 Installing the front VGA/LAN module . . . . . . . . . . . . . . 308

13.3.10 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 308

13.4 Replacing the front VGA cable and/or front LAN cable . . . 309

13.4.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 309

13.4.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 309

13.4.3 Removing the defective front VGA cable and/or front

LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310

13.4.4 Installing the new front VGA cable and/or front LAN cable . . . 310

13.4.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 311

13.5 Replacing the front LAN card . . . . . . . . . . . . . . . . . 312

13.5.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 312

13.5.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 312

13.5.3 Removing the defective front LAN card . . . . . . . . . . . . . 312

13.5.4 Installing the new front LAN card . . . . . . . . . . . . . . . . 313

13.5.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 313

13.6 Replacing the front panel board . . . . . . . . . . . . . . . 314

13.6.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 314

13.6.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 315

13.6.3 Removing the defective front panel board . . . . . . . . . . . 315

13.6.4 Installing the new front panel module . . . . . . . . . . . . . . 319

13.6.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 323

14 Serial interface . . . . . . . . . . . . . . . . . . . . . . . . . 325

14.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 325

14.2 Installing the serial interface . . . . . . . . . . . . . . . . . 325

14.2.1 Required tools . . . . . . . . . . . . . . . . . . . . . . . . . 326

14.2.2 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 326

14.2.3 Removing the slot cover . . . . . . . . . . . . . . . . . . . . 326

14.2.4 Installing the serial interface . . . . . . . . . . . . . . . . . . 327

Page is loading ...

Fujitsu PRIMERGY RX200 S7 User manual

Related papers

Other documents