Fujitsu AN BX2580M1 User manual

Category
Servers
Type
User manual
Upgrade and Maintenance Manual - English
FUJITSU Server PRIMERGY BX2580 M1
Server Blade
Upgrade and Maintenance Manual
Edition June 2015
Copyright and Trademarks
CommentsSuggestionsCorrections
The User Documentation Department would like to
know your opinion of this manual. Your feedback helps
us optimize our documentation to suit your individual
needs.
Feel free to send us your comments by e-mail to
Certified documentation
according to DIN EN ISO 9001:2008
To ensure a consistently high quality standard and
user-friendliness, this documentation was created to
meet the regulations of a quality management system
which complies with the requirements of the standard
DIN EN ISO 9001:2008.
cognitas. Gesellschaft für Technik-Dokumentation mbH
www.cognitas.de
Copyright © 2015 Fujitsu Technology Solutions GmbH.
All rights reserved.
Delivery subject to availability; right of technical modifications reserved.
All hardware and software names used are trademarks of their respective manufacturers.
The contents of this manual may be revised without prior notice.
Fujitsu assumes no liability for damages to third party copyrights or other rights arising from
the use of any information in this manual.
No part of this manual may be reproduced in any form without the prior written permission
of Fujitsu.
Microsoft, Windows, Windows Server, and Hyper V are trademarks or registered trademarks of
Microsoft Corporation in the USA and other countries.
Intel and Xeon are trademarks or registered trademarks of Intel Corporation or its subsidiaries
in the USA and other countries.
BX2580 M1
Upgrade and Maintenance Manual
Before reading this manual
For your safety
This manual contains important information for safely and correctly using this
product.
Carefully read the manual before using this product. Pay particular attention to
the accompanying manual "Safety Notes and Regulations" and ensure these
safety notes are understood before using the product. Keep this manual and the
manual "Safety Notes and Regulations" in a safe place for easy reference while
using this product.
Radio interference
This product is a "Class A" ITE (Information Technology Equipment). In a
domestic environment this product may cause radio interference, in which case
the user may be required to take appropriate measures. VCCI-A
Aluminum electrolytic capacitors
The aluminum electrolytic capacitors used in the product's printed circuit board
assemblies and in the mouse and keyboard are limited-life components. Use of
these components beyond their operating life may result in electrolyte leakage
or depletion, potentially causing emission of foul odor or smoke.
As a guideline, in a normal office environment (25°C) operating life is not
expected to be reached within the maintenance support period (5 years).
However, operating life may be reached more quickly if, for example, the
product is used in a hot environment. The customer shall bear the cost of
replacing replaceable components which have exceeded their operating life.
Note that these are only guidelines, and do not constitute a guarantee of
trouble-free operation during the maintenance support period.
High safety use
This product has been designed and manufactured to be used in commercial
and/or industrial areas as a server.
When used as visual display workplace, it must not be placed in the direct field
of view to avoid incommoding reflections (applies only to TX server systems).
The device has not been designed or manufactured for uses which demand an
extremely high level of safety and carry a direct and serious risk of life or body
if such safety cannot be assured.
Upgrade and Maintenance Manual
BX2580 M1
These uses include control of nuclear reactions in nuclear power plants,
automatic airplane flight control, air traffic control, traffic control in mass
transport systems, medical devices for life support, and missile guidance
control in weapons systems (hereafter, "high safety use"). Customers should
not use this product for high safety use unless measures are in place for
ensuring the level of safety demanded of such use. Please consult the sales
staff of Fujitsu if intending to use this product for high safety use.
Measures against momentary voltage drop
This product may be affected by a momentary voltage drop in the power supply
caused by lightning. To prevent a momentary voltage drop, use of an AC
uninterruptible power supply is recommended.
(This notice follows the guidelines of Voltage Dip Immunity of Personal
Computer issued by JEITA, the Japan Electronics and Information Technology
Industries Association.)
Technology controlled by the Foreign Exchange and Foreign Trade
Control Law of Japan
Documents produced by Fujitsu may contain technology controlled by the
Foreign Exchange and Foreign Trade Control Law of Japan. Documents which
contain such technology should not be exported from Japan or transferred to
non-residents of Japan without first obtaining authorization in accordance with
the above law.
Harmonic Current Standards
This product conforms to harmonic current standard JIS C 61000-3-2.
Only for the Japanese market: About SATA hard disk drives
The SATA version of this server supports hard disk drives with SATA / BC-SATA
storage interfaces. Please note that the usage and operation conditions differ
depending on the type of hard disk drive used.
Please refer to the following internet address for further information on the
usage and operation conditions of each available type of hard disk drive:
http://jp.fujitsu.com/platform/server/primergy/harddisk/
BX2580 M1
Upgrade and Maintenance Manual
Only for the Japanese market:
IAlthough described in this manual, some sections do not apply to the
Japanese market. These options and routines include:
CSS (Customer Self Service)
Upgrade and Maintenance Manual
BX2580 M1
Version history
Issue number Reason for update
First Draft First Issue
V2.0 iRMC microSD card
BX2580 M1
Upgrade and Maintenance Manual
Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.1 Notational conventions . . . . . . . . . . . . . . . . . . . . 16
2 Before you start . . . . . . . . . . . . . . . . . . . . . . . . 17
2.1 Classification of procedures . . . . . . . . . . . . . . . . . 19
2.1.1 Customer Replaceable Units (CRU) . . . . . . . . . . . . . . . 19
2.1.2 Upgrade and Repair Units (URU) . . . . . . . . . . . . . . . . 20
2.1.3 Field Replaceable Units (FRU) . . . . . . . . . . . . . . . . . 21
2.2 Average task duration . . . . . . . . . . . . . . . . . . . . . 22
2.3 Tools you need at hand . . . . . . . . . . . . . . . . . . . . 23
2.4 Documents you need at hand . . . . . . . . . . . . . . . . . 24
3 Important information . . . . . . . . . . . . . . . . . . . . . 27
3.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . 27
3.2 CE conformity . . . . . . . . . . . . . . . . . . . . . . . . . 34
3.3 FCC Class A Compliance Statement . . . . . . . . . . . . . 35
3.4 Environmental protection . . . . . . . . . . . . . . . . . . . 36
4 Basic hardware procedures . . . . . . . . . . . . . . . . . . 39
4.1 Using diagnostics information . . . . . . . . . . . . . . . . 39
4.1.1 Accessing the management blade web interface . . . . . . . . 39
4.1.2 Locating the defective server blade . . . . . . . . . . . . . . . 41
4.1.3 Determining the error class . . . . . . . . . . . . . . . . . . . 42
4.1.3.1 Global Error indicator . . . . . . . . . . . . . . . . . . . . 43
4.1.3.2 Customer Self Service (CSS) indicator . . . . . . . . . . . 44
4.1.4 Locating the defective component . . . . . . . . . . . . . . . . 45
4.2 Shutting down the server blade . . . . . . . . . . . . . . . . 48
4.3 Removing a server blade . . . . . . . . . . . . . . . . . . . 49
4.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 49
Upgrade and Maintenance Manual
BX2580 M1
Contents
4.3.2 Removing the server blade from the system unit . . . . . . . . . 50
4.4 Opening the server blade . . . . . . . . . . . . . . . . . . . . 51
4.5 Closing the server blade . . . . . . . . . . . . . . . . . . . . 52
4.6 Installing the server blade in the system unit . . . . . . . . . 53
4.7 Switching on the server blade . . . . . . . . . . . . . . . . . 56
4.8 Concluding software tasks . . . . . . . . . . . . . . . . . . . 57
5 Basic software procedures . . . . . . . . . . . . . . . . . . . 59
5.1 Starting the maintenance task . . . . . . . . . . . . . . . . . 59
5.1.1 Launching a video redirection to a server blade . . . . . . . . . 59
5.1.2 Checking the server blade status . . . . . . . . . . . . . . . . . 59
5.1.2.1 Checking the server blade status via management blade web
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
5.1.2.2 Checking the server blade status via iRMC . . . . . . . . . . 60
5.1.3 Saving BIOS settings . . . . . . . . . . . . . . . . . . . . . . . 61
5.1.4 Saving iRMC settings . . . . . . . . . . . . . . . . . . . . . . . 61
5.1.5 Connecting virtual media to the managed server blade . . . . . 62
5.1.6 Suspending BitLocker functionality . . . . . . . . . . . . . . . . 63
5.1.7 Disabling boot watchdog functionality . . . . . . . . . . . . . . 64
5.1.7.1 Viewing boot watchdog settings . . . . . . . . . . . . . . . . 64
5.1.7.2 Configuring boot watchdog settings . . . . . . . . . . . . . . 65
5.1.8 Verifying and configuring the backup software solution . . . . . . 67
5.1.9 Note on server maintenance in a Multipath I/O environment . . . 67
5.1.10 Switching on the ID indicator . . . . . . . . . . . . . . . . . . . 70
5.2 Completing the maintenance task . . . . . . . . . . . . . . . 71
5.2.1 Updating or recovering the system board BIOS and iRMC . . . . 71
5.2.1.1 Updating or recovering the system board BIOS . . . . . . . . 71
5.2.1.2 Updating or recovering the iRMC . . . . . . . . . . . . . . . 74
5.2.2 Restoring BIOS settings . . . . . . . . . . . . . . . . . . . . . 76
5.2.3 Restoring iRMC settings . . . . . . . . . . . . . . . . . . . . . 77
5.2.4 Updating mezzanine card firmware . . . . . . . . . . . . . . . . 77
5.2.5 Enabling Option ROM scan . . . . . . . . . . . . . . . . . . . . 79
5.2.6 Verifying and configuring the backup software solution . . . . . . 80
5.2.7 Resetting the boot retry counter . . . . . . . . . . . . . . . . . 81
5.2.7.1 Viewing the boot retry counter . . . . . . . . . . . . . . . . 81
5.2.7.2 Resetting the boot retry counter . . . . . . . . . . . . . . . . 81
BX2580 M1
Upgrade and Maintenance Manual
Contents
5.2.8 Resetting the error status after replacing memory modules or
processors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
5.2.8.1 Memory modules . . . . . . . . . . . . . . . . . . . . . . . 83
5.2.8.2 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . 84
5.2.9 Enabling boot watchdog functionality . . . . . . . . . . . . . . 86
5.2.10 Enabling replaced components in the system BIOS . . . . . . . 87
5.2.11 Verifying the memory mode . . . . . . . . . . . . . . . . . . . 87
5.2.12 Verifying the system time settings . . . . . . . . . . . . . . . . 88
5.2.13 Viewing and clearing the System Event Log (SEL) . . . . . . . 89
5.2.13.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . 89
5.2.13.2 Saving the SEL . . . . . . . . . . . . . . . . . . . . . . . . 90
5.2.13.3 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . . 91
5.2.14 Updating the NIC configuration file in a Linux environment . . . 91
5.2.15 Resuming BitLocker functionality . . . . . . . . . . . . . . . . 93
5.2.16 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 94
5.2.17 Looking up changed MAC / WWN addresses . . . . . . . . . . 94
5.2.17.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . 95
5.2.17.2 Looking up WWN addresses . . . . . . . . . . . . . . . . . 95
5.2.18 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 96
5.2.19 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . 96
5.2.19.1 After replacing / upgrading LAN/CNA controllers . . . . . . 96
5.2.19.2 After replacing the server blade . . . . . . . . . . . . . . . 97
5.2.20 Switching off the ID indicator . . . . . . . . . . . . . . . . . . 97
6 Solid state drives . . . . . . . . . . . . . . . . . . . . . . . . 99
6.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 99
6.2 Installing SSDs . . . . . . . . . . . . . . . . . . . . . . . . . 100
6.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 100
6.2.2 Location of the drive modules inside the server blade . . . . . . 101
6.2.3 Mounting the SSDs into their frames . . . . . . . . . . . . . . 103
6.2.4 Installing the drive module onto the mounting platform . . . . . 105
6.2.5 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 106
6.3 Removing SSDs . . . . . . . . . . . . . . . . . . . . . . . . 107
6.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 107
6.3.2 Removing an SSD . . . . . . . . . . . . . . . . . . . . . . . . 108
6.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 110
6.4 Replacing SSDs . . . . . . . . . . . . . . . . . . . . . . . . 111
6.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 111
6.4.2 Removing an SSD . . . . . . . . . . . . . . . . . . . . . . . . 111
Upgrade and Maintenance Manual
BX2580 M1
Contents
6.4.3 Installing an SSD . . . . . . . . . . . . . . . . . . . . . . . . 112
6.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 112
6.5 Replacing SAS / PCH mounting frames . . . . . . . . . . . 113
6.5.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 113
6.5.2 Removing the mounting frame . . . . . . . . . . . . . . . . . 113
6.5.3 Installing the mounting frame . . . . . . . . . . . . . . . . . . 113
6.5.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 114
7 Mezzanine cards . . . . . . . . . . . . . . . . . . . . . . . 115
7.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 116
7.1.1 Installing riser cards . . . . . . . . . . . . . . . . . . . . . . . 118
7.1.2 Removing riser cards . . . . . . . . . . . . . . . . . . . . . . 120
7.1.3 Population rules for mezzanine cards . . . . . . . . . . . . . 122
7.2 Installing mezzanine cards . . . . . . . . . . . . . . . . . . 128
7.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 128
7.2.2 Installing a mezzanine card . . . . . . . . . . . . . . . . . . . 129
7.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 133
7.3 Removing mezzanine cards . . . . . . . . . . . . . . . . . 134
7.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 134
7.3.2 Removing a mezzanine card . . . . . . . . . . . . . . . . . . 135
7.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 137
7.4 Replacing mezzanine cards . . . . . . . . . . . . . . . . . . 138
7.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 138
7.4.2 Removing a mezzanine card . . . . . . . . . . . . . . . . . . 138
7.4.3 Installing a mezzanine card . . . . . . . . . . . . . . . . . . . 138
7.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 139
8 Main memory . . . . . . . . . . . . . . . . . . . . . . . . . 141
8.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 142
8.1.1 Memory sequence . . . . . . . . . . . . . . . . . . . . . . . 142
8.1.1.1 Population rules . . . . . . . . . . . . . . . . . . . . . . . 142
8.1.1.2 Independent Channel Mode . . . . . . . . . . . . . . . . . 144
8.1.1.3 Mirrored Channel and Performance Modes . . . . . . . . . 146
8.1.1.4 Rank Sparing Mode . . . . . . . . . . . . . . . . . . . . . 147
8.2 Installing memory modules . . . . . . . . . . . . . . . . . . 152
8.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 152
BX2580 M1
Upgrade and Maintenance Manual
Contents
8.2.2 Installing a memory module . . . . . . . . . . . . . . . . . . . 152
8.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 154
8.3 Removing memory modules . . . . . . . . . . . . . . . . . . 155
8.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 155
8.3.2 Removing a memory module . . . . . . . . . . . . . . . . . . 156
8.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 156
8.4 Replacing memory modules . . . . . . . . . . . . . . . . . . 158
8.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 158
8.4.2 Removing a memory module . . . . . . . . . . . . . . . . . . 158
8.4.3 Installing a memory module . . . . . . . . . . . . . . . . . . . 158
8.4.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 159
8.5 Usage of dummy DIMM modules . . . . . . . . . . . . . . . 160
8.6 Handling of memory air cowls . . . . . . . . . . . . . . . . . 161
8.6.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . . 161
8.6.2 Installing the air cowls . . . . . . . . . . . . . . . . . . . . . . 162
8.6.3 Removing the air cowls . . . . . . . . . . . . . . . . . . . . . 163
9 Processors . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
9.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 165
9.2 Installing processors . . . . . . . . . . . . . . . . . . . . . . 166
9.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 166
9.2.2 Installing a processor . . . . . . . . . . . . . . . . . . . . . . 167
9.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 174
9.3 Removing processors . . . . . . . . . . . . . . . . . . . . . 175
9.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 175
9.3.2 Removing a processor . . . . . . . . . . . . . . . . . . . . . . 176
9.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 186
9.4 Upgrading or replacing processors . . . . . . . . . . . . . . 187
9.4.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 187
9.4.2 Upgrading or replacing a processor . . . . . . . . . . . . . . . 188
9.4.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 188
9.5 Handling processor heat sinks . . . . . . . . . . . . . . . . 189
9.5.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 189
9.5.2 Installing processor heat sinks . . . . . . . . . . . . . . . . . . 190
9.5.2.1 Preparing heat sink and processor . . . . . . . . . . . . . . 192
9.5.2.2 Installing the heat sink for CPU 1 . . . . . . . . . . . . . . 193
9.5.2.3 Installing the heat sink for CPU 2 . . . . . . . . . . . . . . 194
Upgrade and Maintenance Manual
BX2580 M1
Contents
9.5.3 Removing processor heat sinks . . . . . . . . . . . . . . . . 196
9.5.4 Removing the "dummy heat sink" of CPU 2 . . . . . . . . . . 197
9.5.5 Replacing processor heat sinks . . . . . . . . . . . . . . . . . 198
9.5.5.1 Removing the processor heat sink . . . . . . . . . . . . . 198
9.5.5.2 Applying thermal paste . . . . . . . . . . . . . . . . . . . 198
9.5.5.3 Installing the processor heat sink . . . . . . . . . . . . . . 198
9.5.6 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 198
9.6 Applying thermal paste . . . . . . . . . . . . . . . . . . . . 199
10 System board components . . . . . . . . . . . . . . . . . . 201
10.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 201
10.2 Replacing the CMOS battery . . . . . . . . . . . . . . . . . 202
10.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 202
10.2.2 Replacing the battery . . . . . . . . . . . . . . . . . . . . . . 203
10.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 205
10.3 USB Flash Module (UFM) . . . . . . . . . . . . . . . . . . . 206
10.3.1 Installing the UFM . . . . . . . . . . . . . . . . . . . . . . . 206
10.3.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 206
10.3.1.2 Installing the UFM . . . . . . . . . . . . . . . . . . . . . . 207
10.3.1.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 209
10.3.1.4 Software configuration . . . . . . . . . . . . . . . . . . . 210
10.3.2 Removing the UFM . . . . . . . . . . . . . . . . . . . . . . . 211
10.3.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 211
10.3.2.2 Removing the UFM . . . . . . . . . . . . . . . . . . . . . 212
10.3.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 212
10.3.3 Replacing the UFM . . . . . . . . . . . . . . . . . . . . . . . 213
10.3.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 213
10.3.3.2 Removing the UFM . . . . . . . . . . . . . . . . . . . . . 214
10.3.3.3 Re-installing the UFM . . . . . . . . . . . . . . . . . . . . 215
10.3.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 217
10.3.3.5 Software configuration . . . . . . . . . . . . . . . . . . . 217
10.4 Trusted Platform Module (TPM) . . . . . . . . . . . . . . . . 218
10.4.1 Installing the TPM . . . . . . . . . . . . . . . . . . . . . . . . 218
10.4.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 218
10.4.1.2 Installing the TPM . . . . . . . . . . . . . . . . . . . . . . 219
10.4.1.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . 222
10.4.2 Removing the TPM . . . . . . . . . . . . . . . . . . . . . . . 224
10.4.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . 225
BX2580 M1
Upgrade and Maintenance Manual
Contents
10.4.2.2 Removing the TPM . . . . . . . . . . . . . . . . . . . . . . 226
10.4.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 227
10.4.3 Replacing the TPM . . . . . . . . . . . . . . . . . . . . . . . 228
10.4.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 229
10.4.3.2 Removing the TPM . . . . . . . . . . . . . . . . . . . . . . 229
10.4.3.3 Re-installing the TPM . . . . . . . . . . . . . . . . . . . . 229
10.4.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 229
10.5 SATA DOM . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
10.5.1 Installing the SATA DOM . . . . . . . . . . . . . . . . . . . . 230
10.5.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 230
10.5.1.2 Mounting the SATA-DOM . . . . . . . . . . . . . . . . . . 231
10.5.1.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 233
10.5.2 Removing the SATA-DOM . . . . . . . . . . . . . . . . . . . . 234
10.5.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 234
10.5.2.2 Removing the SATA DOM . . . . . . . . . . . . . . . . . . 235
10.5.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 235
10.5.3 Replacing the SATA-DOM . . . . . . . . . . . . . . . . . . . . 236
10.5.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 236
10.5.3.2 Removing the SATA DOM . . . . . . . . . . . . . . . . . . 236
10.5.3.3 Installing the SATA DOM . . . . . . . . . . . . . . . . . . . 236
10.5.3.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 236
10.6 iRMC microSD card . . . . . . . . . . . . . . . . . . . . . . 238
10.6.1 Installing the iRMC microSD card . . . . . . . . . . . . . . . . 238
10.6.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 238
10.6.1.2 Installing the iRMC microSD card . . . . . . . . . . . . . . 239
10.6.1.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 240
10.6.2 Removing the iRMC microSD card . . . . . . . . . . . . . . . 240
10.6.2.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 240
10.6.2.2 Removing the iRMC microSD card . . . . . . . . . . . . . 241
10.6.2.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 241
10.6.3 Replacing the iRMC microSD card . . . . . . . . . . . . . . . 242
10.6.3.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . 242
10.6.3.2 Replacing the iRMC microSD card . . . . . . . . . . . . . . 242
10.6.3.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . 242
10.7 Replacing the system board . . . . . . . . . . . . . . . . . . 243
10.7.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 244
10.7.2 Removing the system board . . . . . . . . . . . . . . . . . . . 245
10.7.3 Installing the system board . . . . . . . . . . . . . . . . . . . 247
10.7.4 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 249
Upgrade and Maintenance Manual
BX2580 M1
Contents
11 Server blade . . . . . . . . . . . . . . . . . . . . . . . . . . 251
11.1 Replacing the server blade . . . . . . . . . . . . . . . . . . 251
11.1.1 Preliminary steps . . . . . . . . . . . . . . . . . . . . . . . . 251
11.1.2 Replacing steps . . . . . . . . . . . . . . . . . . . . . . . . . 252
11.1.3 Concluding steps . . . . . . . . . . . . . . . . . . . . . . . . 253
12 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
12.1 Mechanical overview . . . . . . . . . . . . . . . . . . . . . 255
12.1.1 Server blade front . . . . . . . . . . . . . . . . . . . . . . . . 255
12.1.2 Server blade interior . . . . . . . . . . . . . . . . . . . . . . 256
12.2 Configuration tables . . . . . . . . . . . . . . . . . . . . . . 257
12.2.1 Memory configuration table . . . . . . . . . . . . . . . . . . . 257
12.2.2 Mezzanine card configuration table . . . . . . . . . . . . . . . 257
12.3 Connectors and indicators . . . . . . . . . . . . . . . . . . 258
12.3.1 Connectors and indicators on the system board . . . . . . . . 258
12.3.1.1 Onboard connectors . . . . . . . . . . . . . . . . . . . . . 258
12.3.1.2 Onboard settings . . . . . . . . . . . . . . . . . . . . . . 259
12.3.1.3 Onboard indicators and controls . . . . . . . . . . . . . . 260
12.3.2 Connectors and indicators on the front panel . . . . . . . . . . 263
12.3.2.1 Front panel connectors . . . . . . . . . . . . . . . . . . . 263
12.3.2.2 Front panel indicators . . . . . . . . . . . . . . . . . . . . 264
12.4 Minimum startup configuration . . . . . . . . . . . . . . . . 267
BX2580 M1
Upgrade and Maintenance Manual 15
1 Introduction
This Upgrade and Maintenance Manual provides instructions for the following
procedures:
Upgrading the server configuration by adding optional hardware
components
Upgrading the server configuration by replacing existing hardware
components with superior ones.
Replacing defective hardware components
This manual focuses on on-site maintenance tasks. It is recommended to
prepare each service assignment following remote diagnostics procedures, as
described in the "ServerView Suite Local Service Concept (LSC)" manual (see
section "Documents you need at hand" on page 24.
VCAUTION!
The document at hand comprises procedures of a wide range of
complexity. Check the profile of qualification for technicians before
assigning tasks. Before you start, carefully read "Classification of
procedures" on page 19.
16 Upgrade and Maintenance Manual
BX2580 M1
Introduction
1.1 Notational conventions
The following notational conventions are used in this manual:
Text in italics indicates commands or menu items
fixed font indicates system output
semi-bold fixed
font
indicates text to be entered by the user
"Quotation marks" indicate names of chapters and terms that are being
emphasized
Êdescribes activities that must be performed in the order
shown
[Abc] indicates keys on the keyboard
VCAUTION! Pay particular attention to texts marked with this symbol!
Failure to observe this warning may endanger your life,
destroy the system or lead to the loss of data.
Iindicates additional information, notes and tips
indicates the procedure category in terms of complexity
and qualification requirements, see "Classification of
procedures" on page 19
indicates the average task duration, see "Average task
duration" on page 22
BX2580 M1
Upgrade and Maintenance Manual 17
2 Before you start
Before you start any upgrade or maintenance task, please proceed as follows:
ÊCarefully read the safety instructions in chapter "Important information" on
page 27.
ÊMake sure that all necessary manuals are available. Refer to the
documentation overview in section "Documents you need at hand" on
page 24. Print the PDF files if required.
ÊMake yourself familiar with the procedure categories introduced in section
"Classification of procedures" on page 19.
ÊEnsure that all required tools are available according to section "Tools you
need at hand" on page 23.
Installing optional components
The "FUJITSU Server PRIMERGY BX2580 M1 Server Blade Operating
manual" gives an introduction to server features and provides an overview of
available hardware options.
Use the Fujitsu ServerView Suite management software to prepare hardware
expansions. ServerView Suite documentation is available online at
http://manuals.ts.fujitsu.com (http://jp.fujitsu.com/platform/server/primergy/manual/
for the Japanese market). Please refer to the following ServerView Suite topics:
– Operation
– Virtualization
– Maintenance
IFor the latest information on hardware options, refer to your server’s
hardware configurator available online at the following address:
for the global market:
http://ts.fujitsu.com/products/standard_servers/index.html
for the Japanese market:
http://jp.fujitsu.com/platform/server/primergy/system/
Please contact your local Fujitsu customer service partner for details on how to
order expansion kits or spare parts. Use the Fujitsu Illustrated Spares Catalog
to identify the required spare part and obtain technical data and order
information. Illustrated Spares catalogs are available online at
http://manuals.ts.fujitsu.com/illustrated_spares (global market only).
18 Upgrade and Maintenance Manual
BX2580 M1
Before you start
Replacing a defective component
The global error indicators on the front side of the server blade as well as local
diagnostic LEDs on the front panel report defective hardware components that
need to be replaced. For further information on the controls and indicators of
your server, refer to the "FUJITSU Server PRIMERGY BX2580 M1 Server
Blade Operating Manual" and section "Connectors and indicators" on page 258.
If the system has been powered off in order to replace a non-hot plug unit, a
system of PRIMERGY diagnostic indicators guides you to the defective
component. The "Indicate CSS" button enables the indicator next to the
defective component even if the server has been switched off and disconnected
from the mains. For further information, please refer to sections "Using
diagnostics information" on page 39 and "Connectors and indicators on the
front panel" on page 263.
If the defective component is a customer replaceable unit included in the CSS
concept (Customer Self Service, only available for global market), the CSS
indicators on the front side of the server blade will light up.
For further information, refer to the "ServerView Suite Local Service Concept
(LSC)" manual available online at http://manuals.ts.fujitsu.com (global market) or
http://jp.fujitsu.com/platform/server/primergy/manual/ (Japanese market).
It is recommended to prepare local maintenance tasks using remote diagnostics
procedures, as described in the "ServerView Suite Local Service Concept
(LSC)" manual.
BX2580 M1
Upgrade and Maintenance Manual 19
Before you start
2.1 Classification of procedures
The complexity of maintenance procedures varies significantly. Procedures
have been assigned to one of two unit categories, indicating the level of difficulty
and required qualification.
At the beginning of each procedure, the involved unit type is indicated by one of
the symbols introduced in this section.
IPlease ask your local Fujitsu service center for more detailed
information.
2.1.1 Customer Replaceable Units (CRU)
Customer Replaceable Units are intended for customer self service and may be
installed or replaced as hot-plug components during operation.
IComponents that the customer is entitled to replace may differ according
to the service form in his country.
Hot-plug components increase system availability and guarantee a high degree
of data integrity and fail-safe performance. Procedures can be carried out
without shutting down the server or going offline.
Components that are handled as Customer Replaceable Units
No hot-plug modules inside BX2580 M1
Customer Replaceable Units (CRU)
20 Upgrade and Maintenance Manual
BX2580 M1
Before you start
2.1.2 Upgrade and Repair Units (URU)
Upgrade and Repair Units are non hot-plug components that can be ordered
separately to be installed as options (Upgrade Units) or are available to the
customer through customer self service (Repair Units).
IServer management error messages and diagnostic indicators on the
front panel and system board will report defective Upgrade and Repair
Units as customer replaceable CSS components.
Upgrade and repair procedures involve shutting down and opening the server.
VCAUTION!
The device may be seriously damaged or cause damage if it is opened
without authorization or if repairs are attempted by unauthorized and
untrained personnel.
Components that are handled as Upgrade Units
Processors (upgrade kits)
Mezzanine cards
Memory modules
iRMC microSD card
Components that are handled solely as Repair Units
CMOS battery
Non hot-plug solid state drives
Upgrade and Repair Units (URU)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268

Fujitsu AN BX2580M1 User manual

Category
Servers
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI