www.simrad-yachting.com
Waypoints & Routes
App Guide
ENGLISH
V 1.0
2
CONTENTS
3 Preface
4 Overview
5 Waypoints
5 Create a waypoint
6 Edit a waypoint
6 Delete a waypoint
7 Delete all waypoints
8 Filter and sort waypoints
9 Export waypoints
9 Export all waypoints
10 Import waypoints
11 Routes
11 Create a route
12 Autoroute a leg
14 Edit a route
14 Delete a route
15 Delete all routes
16 Import routes
16 Export a route
17 Export all routes
18 Filter and sort routes
3
PREFACE
⚠WARNING: Refer to important safety information in the operator manual and review all warnings, limitations,
and disclaimers before using this product.
Disclaimer
This product is not a substitute for proper training and prudent seamanship. It is the owner’s sole responsibility to install and use
the equipment in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely
responsible for observing maritime safety practices.
Navigational features that appear in this guide are not a substitute for proper training and prudent seamanship. They do not
replace a human navigator and SHOULD NOT be relied on as a sole or primary source of navigation. It is the operator’s sole
responsibility to use more than one navigational methods to ensure the route suggested by the system is safe.
NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS
PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW.
This manual represents the product as at the time of printing. Navico Holding AS and its subsidiaries, branches and aliates
reserve the right to make changes to the product and/or specications at any time without notice. Please contact your nearest
distributor if you require any further assistance.
Copyright
Copyright © 2022 Navico Holding AS.
Trademarks
®Reg. U.S. Pat. & Tm. O, and ™ common law marks. Visit www.navico.com/intellectual-property to review the global trademark
rights and accreditations for Navico Holding AS and other entities.
• Navico® is a trademark of Navico Holding AS.
• Simrad® is a trademark of Kongsberg Maritime AS, licensed to Navico Holding AS.
• SD™ and microSD™ are trademarks of SD-3C, LLC.
Internet usage
Some features in this product use an internet connection to perform data downloads and uploads. Internet usage via a connected
mobile/cell phone internet connection or a pay-per-MB type internet connection may require large data usage. Your service
provider may charge you based on the amount of data you transfer. If you are unsure, contact your service provider to conrm
rates and restrictions. Contact your service provider for information about charges and data download restrictions.
About this manual
Product features
Features described and illustrated in this guide may vary from your display unit due to continuous development of the software.
Document updates
For the latest version of this document in supported languages, visit: www.simrad-yachting.com.
4
OVERVIEW
The Waypoints & Routes app allows you to add, edit and delete waypoints and routes. It also lets
you navigate to a waypoint and navigate a route.
All available waypoints and routes can be managed from the Waypoints & Routes app. Waypoints
and routes created using this app are visible in the Chart app, and vice versa.
A
BE
CF
D
G
A Your vessel
B Waypoints tab - select to view a list of all saved waypoints
C New waypoints button - select to create a new waypoint
D Import waypoints button - select to import waypoints
E Routes tab - select to view a list of all saved routes
F Add route button - select to create a new route
G Import routes button - select to import routes
¼Note: You can import waypoints and routes into the app from a microSD card or USB storage
device.
¼Note: Saved waypoints and routes synchronize with the Simrad companion mobile app when the
same account is used on the unit and mobile app. An active internet connection is required.
5
WAYPOINTS
A waypoint is a point of reference that marks a location for navigation. From the Waypoints tab
you can create and manage waypoints.
Create a waypoint
Select New waypoints to create a waypoint. Position the waypoint by panning the chart (A) or
entering a location. To enter a location select the Coordinate system you want to use (B), enter
the location details on the number pad (C)., and select Next (D) when you are done.
Your saved waypoint marker shows on the screen (E) and if necessary, you can adjust the
waypoint name, coordinates, marker color and icon from the waypoint details panel (F).
B
A
C
D
E F
6
Edit a waypoint
You can edit a waypoint’s attributes by selecting the waypoint (1), selecting See details (2) and
then selecting Edit (3).
1
2
3
Delete a waypoint
To delete a waypoint, swipe the waypoint to the right then select the red delete button.
Alternatively, select the waypoint (1), select the waypoint options button (2), and then select
Delete (3).
or
1
2
3
9
Export waypoints
To export a waypoint, select the waypoint (1), select the waypoint options button (2) and then
select Export (3). Follow the on-screen prompts to export the le.
¼Note: To export waypoints, insert either a microSD card or USB storage device into the unit.
1
2
3
Export all waypoints
To export all waypoints, select the list options button (1) and then Export all (2).
1
2
11
ROUTES
A route is a series of two or more routepoints used to navigate from one point to another.
Create a route
To create a route, select the Routes tab and select Add route (1).
When the Chart app opens, select and hold locations (2, 3, 4, 5) on the chart in a sequence to
create a series of routepoints. Select Finish when you are done.
1
2
3
4
5
12
Autoroute a leg
You can let the system create an autoroute for each route leg. The system takes into
consideration your vessel’s settings and chart information to determine the autoroute.
¼Note: You are responsible for checking the autoroute suggested by the system is safe. There
could be an error in the chart data (depth, obstacles, other vessels, tides, or the height of objects
like bridges or cables) and there can be errors in your vessel’s settings, speed or current ballast.
To autoroute a leg, select the leg in the list and then the autoroute button (1). The system
automatically suggests a new route for the leg (A).
1
A
14
Edit a route
You can edit a selected route by selecting See details (2) and then selecting Edit (3).
1
2
3
Delete a route
To delete a route, swipe the waypoint to the right then select the red delete button. Alternatively,
select the waypoint (1), select the route options button (2), and then select Delete (3).
1
1
2
2
OR
3
16
Import routes
To import routes from a microSD card or USB storage device, select Import routes (1) if your
routes list is empty. Alternatively, select the list options button (2) and then select Import (3).
1or
2
3
Export a route
To export a route to an external storage device, select the route (1), select the route options
button (2) and then select Export (3).
1
2
3
www.simrad-yachting.com
®Reg. U.S. Pat. & Tm. O, and ™ common law marks.
Visit www.navico.com/intellectual-property to review
the global trademark rights and accreditations for
Navico Holding AS and other entities.
*988-12865-001*
/