2. Computers & electronics
  3. TVs & monitors
  4. Wall & ceiling mounts accessories
  5. Intermec
  6. CK60 Ethernet Multidock
CK60 Ethernet Multidock

Intermec CK60 Ethernet Multidock Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Intermec CK60 Ethernet Multidock Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What are the mounting bracket dimensions?
    What is the minimum hardware size required for installation?
    How many fasteners should be used in each bracket?
    What is the recommended plywood thickness for reinforcement on framed walls?
    How far apart should the mounting brackets be positioned?
1 Position the mounting brackets over the screw holes then using the screws
(included) mount the brackets to the multidock. The mounting holes are 15-3/4
inches (40.01 cm) apart.
2 On framed walls, it is preferable to drive lag screws directly into studs whenever
possible. If this is not possible, it may be necessary to install scab studs or
plywood (5/8 inch thickness or greater) reinforcement.
3 Position mounting brackets at a suitable height and use 1/4 inch or larger
hardware *(lag screws or concrete fasteners) to secure mounting brackets to the
wall. Use two fasteners in each bracket.
4 When installing several multidocks across a wall, be sure to allow clearance
between them for the power cables.
1 Position the mounting brackets over the screw holes then using the screws
(included) mount the brackets to the multidock. The mounting holes are 15-3/4
inches (40.01 cm) apart.
2 On framed walls, it is preferable to drive lag screws directly into studs whenever
possible. If this is not possible, it may be necessary to install scab studs or
plywood (5/8 inch thickness or greater) reinforcement.
3 Position mounting brackets at a suitable height and use 1/4 inch or larger
hardware *(lag screws or concrete fasteners) to secure mounting brackets to the
wall. Use two fasteners in each bracket.
4 When installing several multidocks across a wall, be sure to allow clearance
between them for the power cables.
1 Position the mounting brackets over the screw holes then using the screws
(included) mount the brackets to the multidock. The mounting holes are 15-3/4
inches (40.01 cm) apart.
2 On framed walls, it is preferable to drive lag screws directly into studs whenever
possible. If this is not possible, it may be necessary to install scab studs or
plywood (5/8 inch thickness or greater) reinforcement.
3 Position mounting brackets at a suitable height and use 1/4 inch or larger
hardware *(lag screws or concrete fasteners) to secure mounting brackets to the
wall. Use two fasteners in each bracket.
4 When installing several multidocks across a wall, be sure to allow clearance
between them for the power cables.
Instructions
Corporate Headquarters
6001 36th Avenue West
Everett, Washington 98203 U.S.A.
tel 425.348.2600
www.intermec.com
© 2005 Intermec Technologies
Corporation. All rights reserved.
CK60 Multidock Mounting Brackets Installation Instructions
*931-001-001*
P/N 931-001-001
Instructions
Corporate Headquarters
6001 36th Avenue West
Everett, Washington 98203 U.S.A.
tel 425.348.2600
www.intermec.com
© 2005 Intermec Technologies
Corporation. All rights reserved.
CK60 Multidock Mounting Brackets Installation Instructions
*931-001-001*
P/N 931-001-001
Instructions
Corporate Headquarters
6001 36th Avenue West
Everett, Washington 98203 U.S.A.
tel 425.348.2600
www.intermec.com
© 2005 Intermec Technologies
Corporation. All rights reserved.
CK60 Multidock Mounting Brackets Installation Instructions
*
931-001-001*
P/N 931-001-001
CK60 Multidock Mounting Brackets CK60 Multidock Mounting Brackets
CK60 Multidock Mounting Brackets
Installation Instructions Installation Instructions Installation Instructions
/