Intermec CK60 Ethernet Multidock Quick start guide

CK60 Ethernet Multidock
Intermec
Brand
Intermec
Model
CK60 Ethernet Multidock
Type
Quick start guide

Intermec CK60 Ethernet Multidock lets you charge up to four CK60 Handheld Computers and transfer data through its Ethernet connection. Use it to create a charging station for your CK60 devices or to transfer data between them and a network. The Multidock's compact design and easy setup make it a convenient solution for a variety of applications.

Intermec CK60 Ethernet Multidock lets you charge up to four CK60 Handheld Computers and transfer data through its Ethernet connection. Use it to create a charging station for your CK60 devices or to transfer data between them and a network. The Multidock's compact design and easy setup make it a convenient solution for a variety of applications.

The Intermec CK60 Ethernet Multidock:
• charges up to four CK60 Handheld Computers.
• pass through data from other Ethernet Multidocks
• transfer data through the Ethernet connection.
The CK60 Multidock shipping box should contain these items:
•CK60 Multidock
• CK60 Multidock Quick Start Guide
• Product Warranty Card
• Compliance Statement
What You Need
To use the CK60 Multidock you need:
• an Intermec AC power supply p/n: 851-075-001
•an AC power cord
You need to purchase the appropriate power cord for your location. For more information,
contact your Intermec sales representative.
You must use the appropriate power supply with this device or
equipment damage may occur.
Out of the Box
CK60 Handheld Computer bays
CK60 Ethernet Multidock Front View
CK60 Ethernet Multidock Features
Uplink port
Power supply connector
Switch port
CK60 Ethernet Multidock Rear View
CK60 Ethernet Multidock Features
Environmental Specifications
Operating Temperature:: 0°C to +50°C (+32°F to +122°F)
Storage temperature: -30°C to 70°C (-22°F to +158°F)
Relative Humidity: 5% to 95%
CK60 Ethernet Multidock
Corporate Headquarters
6001 36th Avenue West
Everett, Washington 98203 U.S.A.
tel 425.348.2600
www.intermec.com
© 2005 Intermec Technologies
Corporation. All rights reserved.
CK60 Ethernet Multidock Quick Start Guide
*962-040-017B*
P/N 962-040-017B
Quick Start Guide
Installing Your CK60 Ethernet Multidock
1 Place your CK60 Ethernet Multidock on a flat, stable, and clean surface within 6
feet (1.83m) of an AC power outlet. You can also install your Ethernet Multidock to
a vertical surface using an optional bracket kit. See your Intermec sales represen-
tatvie for details.
2 Connect the Ethernet cables to the ports on the back of your CK60 Ethernet Multi-
dock.
3 Connect the AC power supply to the power connector on the back of your Ether-
net Multidock. Then connect the power supply to an AC power outlet.
The following Sample System Diagram illustrates using the Switch Port to connect
additional Ethernet Multidocks to share a single network connection. The Uplink Port
being used to connect the CK60 Ethernet Multidock to the network.
Sample System Diagram
Multidock Front Bay Status LEDs
Ethernet Connector
Ethernet RJ-45 Connector Pin Outs
Multidock Rear RJ45 Port Status LEDs
AC Power Usage
Each power supply (p/n: 851-075-001) has a maximum AC load current of 2 amps @ 100
volts AC.
Example: You can have 10 CK60 Ethernet Multidocks plugged into one 20 amp circuit
breaker assuming no other loads are drawing off that same circuit breaker.
Shelving Considerations
For building your shelving, keep in mind the dimensions of the dock. Shelving needs to
include enough room above the Ethernet Multidock for inserting the CK60 Mobile
Computer and behind the Ethernet Multidock for connecting the cables.
Charging Time for CK60 Handheld Computers
Your CK60 Handheld Computers fully charge within four hours. The charging status of your
Handheld Computer is observed on the Battery Status LED on your CK60 Handheld
Computer keypad.
Switch port
Uplink port
Switch port
Uplink port
Cable to Network
(For best results Category-5 cables
are recommended)
Data communication LED
(one for each bay)
Indicated States Link Status LED State
Link Established to CK60 Handheld Computer Green
Link /Activity to CK60 Handheld Computer Blinking Green/Green with data activity
Pin Number Signal Name I/O to Computer Description
1 TXP O Ethernet transmit positive
2 TXN O Ethernet transmti negative
3 RXP I Ethernet receive positive
4
5
6 RXN I Ethernet receive negative
7
8
RJ-45 Shell C-GND PWR Chassis Ground
Link Activity LEDs (upper left)
Speed Activity LEDs (upper right)
Indicated States Speed Status LED State Link Status LED State
Speed 10 Mbs Yellow Off N/A
Speed 100 Mbs Yello w On N/A
No Activity N/A Green Off
Link Activity N/A Blinking Green
CK30 Handheld Computer Quick Start Guide
CK60 Ethernet Multidock Quick Start Guide
  • Page 1 1
  • Page 2 2

Intermec CK60 Ethernet Multidock Quick start guide

CK60 Ethernet Multidock
Intermec
Brand
Intermec
Model
CK60 Ethernet Multidock
Type
Quick start guide

Intermec CK60 Ethernet Multidock lets you charge up to four CK60 Handheld Computers and transfer data through its Ethernet connection. Use it to create a charging station for your CK60 devices or to transfer data between them and a network. The Multidock's compact design and easy setup make it a convenient solution for a variety of applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents