ABB Relion PML630 User manual

Brand: ABB

Model: Relion PML630

Type: User manual

This manual is also suitable for

Relion 630 Series

Relion

630 series

Load Shedding Controller

PML630

IEC 61850 Point List Manual

Document ID: 1MRS757261

Issued: 2012-03-29

Revision: C

Product version: 1.1.2

This document and parts thereof must not be reproduced or copied without written

permission from ABB, and the contents thereof must not be imparted to a third

party, nor used for any unauthorized purpose.

The software or hardware described in this document is furnished under a license

and may be used, copied, or disclosed only in accordance with the terms of such

license.

Trademarks

ABB and Relion are registered trademarks of the ABB Group. All other brand or

product names mentioned in this document may be trademarks or registered

trademarks of their respective holders.

Warranty

Please inquire about the terms of warranty from your nearest ABB representative.

http://www.abb.com/substationautomation

Disclaimer

The data, examples and diagrams in this manual are included solely for the concept

or product description and are not to be deemed as a statement of guaranteed

properties. All persons responsible for applying the equipment addressed in this

manual must satisfy themselves that each intended application is suitable and

acceptable, including that any applicable safety or other operational requirements

are complied with. In particular, any risks in applications where a system failure and/

or product failure would create a risk for harm to property or persons (including but

not limited to personal injuries or death) shall be the sole responsibility of the

person or entity applying the equipment, and those so responsible are hereby

requested to ensure that all measures are taken to exclude or mitigate such risks.

This document has been carefully checked by ABB but deviations cannot be

completely ruled out. In case any errors are detected, the reader is kindly requested

to notify the manufacturer. Other than under explicit contractual commitments, in

no event shall ABB be responsible or liable for any loss or damage resulting from

the use of this manual or the application of the equipment.

Conformity

This product complies with the directive of the Council of the European

Communities on the approximation of the laws of the Member States relating to

electromagnetic compatibility (EMC Directive 2004/108/EC) and concerning

electrical equipment for use within specified voltage limits (Low-voltage directive

2006/95/EC). This conformity is the result of tests conducted by ABB in

accordance with the product standards EN 50263 and EN 60255-26 for the EMC

directive, and with the product standards EN 60255-1 and EN 60255-27 for the low

voltage directive. The product is designed in accordance with the international

standards of the IEC 60255 series.

Table of contents

Section 1 Introduction.......................................................................3

This manual........................................................................................3

Intended audience..............................................................................3

Product documentation.......................................................................3

Product documentation set............................................................3

Document revision history.............................................................4

Related documentation..................................................................5

Symbols and conventions...................................................................5

Symbols.........................................................................................5

Document conventions..................................................................5

Functions, codes and symbols......................................................6

Section 2 Logical node list................................................................9

Logical nodes.....................................................................................9

Section 3 Logical node extensions.................................................11

New logical nodes............................................................................11

LSCACLS....................................................................................11

PWSACLS...................................................................................12

LSCCCLS....................................................................................13

SNWLRCLS ................................................................................13

SNWARCLS ...............................................................................14

LSCRCLS ...................................................................................15

Extended logical nodes....................................................................17

LLN0............................................................................................18

LDLLN0.......................................................................................18

LSLLN0........................................................................................18

SNWLLN0....................................................................................19

NCBDLLN0..................................................................................19

LSCLLN0.....................................................................................19

PWSLLN0....................................................................................20

LSCGAPC...................................................................................20

LSPTRC......................................................................................20

PWSGCSWI................................................................................21

PWSGMMXU...............................................................................21

PWSTCSWI.................................................................................22

PWSTMMXU...............................................................................22

NCBDCSWI.................................................................................23

NCBDMMXU...............................................................................23

LDCSWI.......................................................................................23

Table of contents

PML630 1

Point List Manual

LDMMXU.....................................................................................24

SPGGIO .....................................................................................24

DRRDRE.....................................................................................25

DPGGIO......................................................................................25

MVGGIO......................................................................................26

SPVNZBAT..................................................................................26

Section 4 Glossary.........................................................................27

Table of contents

2 PML630

Point List Manual

Section 1 Introduction

1.1 This manual

The point list manual describes the outlook and properties of the data points

specific to the IED. The manual should be used in conjunction with the

corresponding communication protocol manual.

1.2 Intended audience

This manual addresses the communication system engineer or system integrator

responsible for pre-engineering and engineering for communication setup in a

substation from an IED perspective.

The system engineer or system integrator must have a basic knowledge of

communication in protection and control systems and thorough knowledge of the

specific communication protocol.

1.3 Product documentation

1.3.1 Product documentation set

The application engineering guide provides information for IEC 61850 engineering

of the load shedding controller IED, protection and control IEDs and COM600

Station Automation device using PCM600, IET600 and SAB600. With a practical

example, the guide explains all the steps from system planning and engineering to

application functionality and IED parameterization for realizing the load shedding

functionality using the IEDs.

The commissioning manual contains instructions on how to commission the IED

with the load shedding power management functions. The manual can also be used

by system engineers and maintenance personnel for assistance during the testing

phase. The manual provides procedures for checking external circuitry and

energizing the IED, parameter setting and configuration. The manual describes the

process of testing an IED in a substation that is not in service. The chapters are

organized in chronological order in which the IED should be commissioned.

The communication protocol manual describes a communication protocol

supported by the IED. The manual concentrates on vendor-specific implementations.

1MRS757261 C Section 1

Introduction

PML630 3

Point List Manual

The engineering manual contains instructions on how to engineer the IED using

PCM600. The manual provides instructions on how to set up a PCM600 project

and insert IEDs to the project structure. The manual also recommends a sequence

for engineering of load shedding power management function, LHMI functions as

well as communication engineering for IEC 61850.

The installation manual contains instructions on how to install the IED. The

manual provides procedures for mechanical and electrical installation. The chapters

are organized in chronological order in which the IED should be installed.

The operation manual contains instructions on how to operate the IED once it has

been commissioned. The manual provides instructions for monitoring, controlling

and setting the IED.

The point list manual describes the outlook and properties of the data points

specific to the IED. The manual should be used in conjunction with the

corresponding communication protocol manual.

The technical manual contains application and functionality descriptions and lists

function blocks, logic diagrams, input and output signals, setting parameters and

technical data sorted per function. The manual can be used as a technical reference

during the engineering phase, installation and commissioning phase, and during

normal service.

See the 630 series documentation for installation and

commissioning manuals. The PML630 documentation set includes

only application engineering guide, engineering manual, IEC 61850

communication protocol manual, IEC 61850 point list manual,

operation manual and technical manual.

1.3.2 Document revision history

Document revision/date

Product version History

A/2011-05-04 1.1 First release

B/2011-11-03 1.1.1 Content updated

C/2012-03-29 1.1.2 Content updated

Download the latest documents from the ABB Web site

http://www.abb.com/substationautomation.

Section 1 1MRS757261 C

Introduction

4 PML630

Point List Manual

1.3.3 Related documentation

Name of the document Document ID

Application Engineering Guide 1MRS757394

Engineering Manual 1MRS757184

IEC 61850 Communication Protocol Manual 1MRS757260

Operation Manual 1MRS757183

Technical Manual 1MRS757256

Product series- and product-specific manuals can be downloaded from the ABB

Web site http://www.abb.com/substationautomation.

1.4 Symbols and conventions

1.4.1 Symbols

The caution icon indicates important information or warning related

to the concept discussed in the text. It might indicate the presence

of a hazard which could result in corruption of software or damage

to equipment or property.

The information icon alerts the reader of important facts and

conditions.

The tip icon indicates advice on, for example, how to design your

project or how to use a certain function.

Although warning hazards are related to personal injury, it is necessary to

understand that under certain operational conditions, operation of damaged

equipment may result in degraded process performance leading to personal injury

or death. Therefore, comply fully with all warning and caution notices.

1.4.2 Document conventions

A particular convention may not be used in this manual.

• Abbreviations and acronyms in this manual are spelled out in the glossary. The

glossary also contains definitions of important terms.

• Push-button navigation in the LHMI menu structure is presented by using the

push-button icons.

1MRS757261 C Section 1

Introduction

PML630 5

Point List Manual

To navigate between the options, use and .

• HMI menu paths are presented in bold.

Select Main menu/Settings.

• LHMI messages are shown in Courier font.

To save the changes in non-volatile memory, select Yes and press .

• Parameter names are shown in italics.

The function can be enabled and disabled with the Operation setting.

• The ^ character in front of an input or output signal name in the function block

symbol given for a function, indicates that the user can set an own signal name

in PCM600.

• The * character after an input or output signal name in the function block

symbol given for a function, indicates that the signal must be connected to

another function block in the application configuration to achieve a valid

application configuration.

1.4.3 Functions, codes and symbols

Table 1: Functions included in PML630

Functionality IEC 61850

Control

Double point indication

DPGGIO

Monitoring

Station battery supervision

SPVNZBAT

Generic measured values

MVGGIO

Single point indication

SPGGIO

Power management

Critical circuit breaker NCBDCSWI

Contingency based fast load shed LSCACLS

Sheddable load trip LSPTRC

Busbar with sheddable load LDMMXU

Network power source PWSMMXU

Subnetwork output SNWRCLS

Disturbance recorder function

Disturbance recorder

DRRDRE

Analog channels 1-10 (samples)

A1RADR

Analog channel 11-20 (samples)

A2RADR

Analog channel 21-30 (samples) A3RADR

Analog channel 31-40 (calc. val.) A4RADR

Binary channel 1-16 B1RBDR

Table continues on next page

Section 1 1MRS757261 C

Introduction

6 PML630

Point List Manual

Functionality IEC 61850

Binary channel 17-32 B2RBDR

Binary channel 33-48

B3RBDR

Binary channel 49-64

B4RBDR

1) The function is not used by default. However, it is kept enabled in the Application Configuration tool

for instantiation in any additional user defined logic other than the features offered by the IED

Connectivity Package.

1MRS757261 C Section 1

Introduction

PML630 7

Point List Manual

Section 2 Logical node list

2.1 Logical nodes

Table 2: Logical nodes implemented in PML630

Logical node groups Logical node Description

C: Logical nodes for control CSWI

Calculated circuit breaker status

- Critical circuit breaker related information

- Generators

- Grid transformers

- Load feeders

L: System logical nodes

LPHD Physical device information

LLN0 Logical node zero

P: Logical nodes for protection

functions PTRC Load shed trip command

G: Logical nodes for generic

references GAPC Load shedding status (start/operate)

M: Logical nodes for metering

and measurement

MMXU

Measurement:

- Critical circuit breaker related information

- Generators

- Grid transformers

- Load feeders

1MRS757261 C Section 2

Logical node list

PML630 9

Point List Manual

Section 3 Logical node extensions

3.1 New logical nodes

Table 3: New functions in PML630

LN Class Prefix LN Type Description

ACLS LSC LSCACLS

LN Class: 'A' for Automatic control, 'C' for Contingency

based, 'LS' for Load shedding)

LN Prefix: Contingency based Load shedding (Fast

load shedding)

ACLS PWS PWSACLS

LN Class: 'A' for Automatic control, 'C' for Contingency

based, 'LS' for Load shedding)

LN Prefix: PoWer Source (Slow load shedding for Grid

Transformers)

CCLS LSC LSCCCLS

LN Class: 'C' for Supervisory control, 'C' for

Contingency based, 'LS' for Load shedding)

LN Prefix: Load shedding (Manual) Control

RCLS SNWL SNWLRCLS

LN Class: 'R' for (Load shedding) Related (function), 'C'

for Contingency based, 'LS' for Load shedding)

LN Prefix: SubNetWork Load shed information

RCLS SNWL SNWARCLS

LN Class: 'R' for (Load shedding) Related (function), 'C'

for Contingency based, 'LS' for Load shedding)

LN Prefix: SubNetWork Accumulated load power

information

RCLS LSC LSCRCLS

LN Class: 'R' for (Load shedding) Related (function), 'C'

for Contingency based, 'LS' for Load shedding)

LN Prefix: (Substation) Load shedding controller

information summary

3.1.1 LSCACLS

Table 4: LSCACLS

Attribute name

DATA type Explanation M/O/E

ACLS class

ACLS Contingency load shedding (Fast LS) M

Data

Common Logical Node Information

Mod ABB_c_dINC Mode (Fast load shed function

Enable / Disable / Test command/

status)

Beh ABB_a_dINS Behaviour (Reflects the mode of the

function)

Health ABB_c_dINS Health M

NamPlt ABB_b_dLPL Name plate M

Table continues on next page

1MRS757261 C Section 3

Logical node extensions

PML630 11

Point List Manual

Attribute name DATA type Explanation M/O/E

OpCntRs ABB_v4_dSPC LS Operation counter (reset

command/ status)

Controls

Rs ABB_v4_dSPC Load shed function reset command E

SNtw1Rs ABB_v4_dSPC Subnetwork 1 reset command E

SNtw2Rs ABB_v4_dSPC Subnetwork 2 reset command E

SNtw3Rs ABB_v4_dSPC Subnetwork 3 reset command E

SNtw4Rs ABB_v4_dSPC Subnetwork 4 reset command E

Status information

Str ABB_f_dACD Load shed function Start E

Op ABB_b_dACT Load shed function Operate E

3.1.2 PWSACLS

Table 5: PWSACLS

Attribute name DATA type Explanation M/O/E

ACLS class

ACLS Contingency load shedding (Slow LS) M

Data

Common Logical Node Information

Mod ABB_c_dINC Mode (Slow load shed function

Enable / Disable / Test command/

status)

Beh ABB_a_dINS Behaviour (Reflects the mode of the

function)

Health ABB_c_dINS Health M

NamPlt ABB_b_dLPL Name plate M

Measured Values

TmElaTrf ABB_v2_dMV Elapsed time for Grid trasnformer E

TmIDMTTrf ABB_v2_dMV IDMT Time for Grid transformer E

MaxDmdS ABB_v2_dMV Maximum demand MVA limit setting E

MaxCurTrf ABB_v2_dMV Maximum current for grid transformer E

Controls

Rs ABB_v1_dSPC Load shed function reset command E

Status information

Str ABB_f_dACD Load shed function start E

Op ABB_b_dACT Load shed function operate E

TrfOvLod ABB_v1_dSPS Grid transformer overloaded E

MaxDmdExc ABB_v1_dSPS Max Demand Exceeded (Violated) E

MaxDmdTm ABB_v1_dINS Maximum demand time limit setting E

Section 3 1MRS757261 C

Logical node extensions

12 PML630

Point List Manual

3.1.3 LSCCCLS

Table 6: LSCCCLS

Attribute name DATA type Explanation M/O/E

CCLS class

CCLS

Contingency load shedding (Manual

LS) M

Data

Common Logical node information

Mod ABB_c_dINC Mode (Manual load shed function

Enable / Disable / Test command /

status)

Beh ABB_a_dINS Behaviour (Reflects the mode of the

function)

Health ABB_c_dINS Health M

NamPlt ABB_b_dLPL Name plate M

Controls

ManLSCmd ABB_v4_dSPC Subnetwork manual load shed

command

3.1.4 SNWLRCLS

Table 7: SNWLRCLS

Attribute name

DATA type Explanation M/O/E

RCLS class

RCLS

Contingency load shedding related -

Subnetwork information M

Data

Common Logical Node Information

Mod ABB_c_dINC Mode M

Beh ABB_a_dINS Behaviour M

Health ABB_c_dINS Health M

NamPlt ABB_b_dLPL Name plate M

Measured Values

NtwAvbPwr ABB_v2_dMV Network total available power (Sum of

power values from all generators and

grid transformers inclusive of

maximum capabilities)

NtwLod ABB_v2_dMV Network total load E

NtwPwrBal ABB_v2_dMV Network power balance (The spinning

reserve value of the network)

NtwLodInhM ABB_v2_dMV Network load inhibit by Operator (Load

value that is inhibited from being shed

by the operator)

Table continues on next page

1MRS757261 C Section 3

Logical node extensions

PML630 13

Point List Manual

Attribute name DATA type Explanation M/O/E

NtwLodInhS ABB_v2_dMV Network load inhibit by system (Load

value that is inhibited from being shed

by the system)

NtwLodMm ABB_v2_dMV Network load mismatch (Total value of

non-sheddable loads)

NtwShbLod ABB_v2_dMV Network sheddable load (Total value

of sheddable loads (accumulated)

NtwMLodShd ABB_v2_dMV Network must load shed (Load value

that must be shed (at minimum) to

establish power balance)

NtwALodShd ABB_v2_dMV Network actual load shed (Load value

of the calculated shed priority)

NtwPwrDiff ABB_v2_dMV Network power difference (The

difference of load value between

actually shed and must be shed)

Status information

NtwSt ABB_v1_dSPS Network status (Active /Inactive) E

LSBlkSt ABB_v1_dSPS s Load shedding block status E

SlwLSBlkSt ABB_v1_dSPS Slow load shedding block status E

NtwLSPrio ABB_v1_dINS Network actual shed priority (Priority

for load shedding calculated by the

function)

LSOpSt ABB_v1_dINS Fast/Slow/Manual load shed operate E

3.1.5 SNWARCLS

Table 8: SNWARCLS

Attribute name

DATA type Explanation M/O/E

RCLS class

RCLS

Contingency load shedding related -

Subnetwork accumulated load

information M

Data

Common Logical Node Information

Mod ABB_c_dINC Mode (Fast load shed function

Enable / Disable / Test command/

status)

Beh ABB_a_dINS Behaviour (Reflects the mode of the

function)

Health ABB_c_dINS Health M

NamPlt ABB_b_dLPL Name plate M

Measured value

ALodPrio1 ABB_v2_dMV Accumulated Load against Priority 1 E

ALodPrio2 ABB_v2_dMV Accumulated Load against Priority 2 E

ALodPrio3 ABB_v2_dMV Accumulated Load against Priority 3 E

Table continues on next page

Section 3 1MRS757261 C

Logical node extensions

14 PML630

Point List Manual

Page is loading ...

ABB Relion PML630 User manual

Brand: ABB

Model: Relion PML630

Type: User manual

This manual is also suitable for

Relion 630 Series

Download PDF

report

ABB Relion PML630 User manual

This manual is also suitable for

ABB Relion PML630 User manual

Related papers

Other documents