ABB REC650 ANSI User manual

ABB
Brand
ABB
Model
REC650 ANSI
Category
Measuring, testing & control
Type
User manual
Relion
®
650 series
Bay control REC650 ANSI
Product Guide
Contents
1. 650 series overview...........................................................3
2. Application.........................................................................3
3. Available functions.............................................................7
4. Control.............................................................................19
5. Current protection............................................................21
6. Voltage protection............................................................23
7. Frequency protection.......................................................24
8. Secondary system supervision.........................................24
9. Logic...............................................................................25
10. Monitoring......................................................................27
11. Metering.........................................................................30
12. Human Machine interface...............................................30
13. Basic IED functions.........................................................31
14. Station communication...................................................31
15. Hardware description......................................................33
16. Connection diagrams Customized..................................35
17. Connection diagrams Configured....................................40
18. Technical data................................................................64
19. Ordering for Customized IED..........................................98
20. Ordering for Configured IED..........................................102
21. Ordering for Accessories..............................................105
Disclaimer
The information in this document is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no responsibility for any errors
that may appear in this document.
© Copyright 2012 ABB.
All rights reserved.
Trademarks
ABB and Relion are registered trademarks of the ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks
of their respective holders.
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
2 ABB
1. 650 series overview
The 650 series IEDs provide both customized and
configured solutions. With the customized IEDs you
have the freedom to completely adapt the
functionality according to your needs.
The 650 series IEDs provide optimum 'off-the-
shelf', ready-to-use solutions. It is configured with
complete protection functionality and default
parameters to meet the needs of a wide range of
applications for generation, transmission and sub-
transmission grids.
The 650 series IEDs include:
• Customized versions providing the possibility to
adapt the functionality to the application needs.
• Configured solutions are completely ready to use
solutions optimized for a wide range of
applications for generation, transmission and sub-
transmission grids.
• Support for user-defined names in the local
language for signal and function engineering.
• Minimized parameter settings based on default
values and ABB's new global base value concept.
You only need to set those parameters specific to
your own application, such as the line data.
• GOOSE messaging for horizontal communication.
• Extended HMI functionality with 15 dynamic three-
color-indication LEDs per page, on up to three
pages, and configurable push-button shortcuts
for different actions.
• Programmable LED text-based labels.
• Settable 1A/5A -rated current inputs.
2. Application
REC650 is used for the control, protection and
monitoring of different types of bays in power
networks. The IED is especially suitable for
applications in control systems with distributed
control IEDs in all bays with high demands on
reliability. It is suitable for the control of all
apparatuses in single busbar single CB, double
busbar single CB switchgear arrangement.
The control is performed from remote (SCADA/
Station) through the communication bus or from
local HMI. Different control configurations can be
used, and one control IED per bay is
recommended. Interlocking modules are available
for common types of switchgear arrangements. The
control is based on the select before execute
principle to give highest possible security. A
synchronism control function is available to interlock
breaker closing. A synchronizing function where
breaker closes at the right instance in asynchronous
networks is also provided.
A number of protection functions are available for
flexibility in use for different station types and
busbar arrangements. The auto-reclose includes
priority circuits for single-breaker arrangements. It
co-operates with the synchronism check function
with high-speed or delayed reclosing.
High set instantaneous phase and ground
overcurrent, 4 step directional or non-directional
delayed phase and ground overcurrent, thermal
overload and two step under- and overvoltage
functions are examples of the available functions
allowing user to fulfill any application requirement.
Disturbance recording is available to allow
independent post-fault analysis after primary
disturbances.
Three packages have been defined for following
applications:
• Single breaker for single busbar (A01A)
• Single breaker for double busbar (A02A)
• Bus coupler for double busbar (A07A)
The packages are configured and ready for direct
use. Analog and control circuits have been pre-
defined. Other signals need to be applied as
required for each application. The main differences
between the packages above are the interlocking
modules and the number of apparatuses to control.
The graphical configuration tool ensures simple and
fast testing and commissioning.
Bay control REC650 ANSI
1MRK 511 265-BUS B
Product version: 1.2 Issued: June 2012
Revision: B
ABB 3
REC650-A01A – Single Busbar Single breaker 10AI
(4I+1I+5U)
S CSWI
Control
S XCBR
Control
S CSWI
Control
SMB RREC
79 0->1
S CSWI
Control
S CSWI
Control
SMP PTRC
94 1->0
S CSWI
Control
S CSWI
Control
SES RSYN
25 SYNC
TCS SCBR
Cond
TCS SCBR
Cond
SPVN ZBAT
Cond
Other configured functions
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
OV2 PTOV
59 U>
PH PIOC
50 3I>>
CC RBRF
50BF 3I > BF
V MMXU
Meter.
C MMXU
Meter.
ETP MMTR
Wh<->
189
989
989G
289G
189G
EF4 PTOC
51N/67N
IN>
Q CBAY
Control
WA1
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
SEL GGIO
Control
C MSQI
Meter.
V MSQI
Meter.
CV MMXN
Meter.
CC RPLD
52PD PD
DRP RDRE
Mont.
V MMXU
Meter.
IEC61850
ANSI IEC
Function Enabled in Settings
132 kV Bus
1000/5
132kV/110V
132kV/ 110V
OC4 PTOC
51/67 3I>
S SCBR
Cond
S SIMG
63
IEC61850
ANSI IEC
Function Disabled in Settings
ANSI11000137_2_en.vsd
LMB RFLO
Monit.
52
ANSI11000137 V2 EN
Figure 1. A typical protection and control application for a single busbar in single breaker arrangement
Bay control REC650 ANSI
1MRK 511 265-BUS B
Product version: 1.2
4 ABB
REC650-A02A – Double Busbar Single breaker 10AI
(4I+1I+5U)
S CSWI
Control
S XCBR
Control
S CSWI
Control
SMB RREC
79 0->1
S CSWI
Control
S CSWI
Control
SMP PTRC
94 1->0
S CSWI
Control
S CSWI
Control
S CSWI
Control
SES RSYN
25 SYNC
TCS SCBR
Cond
TCS SCBR
Cond
SPVN ZBAT
Cond
Other configured functions
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
OV2 PTOV
59 U>
PH PIOC
50 3I>>
CC RBRF
50BF 3I > BF
V MMXU
Meter.
C MMXU
Meter.
ETP MMTR
Wh<->
52
189
289
989
989G
G
189G
EF4 PTOC
51N/67N
IN>
Q CBAY
Control
WA1
WA2
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
SEL GGIO
Control
C MSQI
Meter.
V MSQI
Meter.
CV MMXN
Meter.
CC RPLD
52PD PD
DRP RDRE
Mont.
V MMXU
Meter.
V MMXU
Meter.
OC4 PTOC
51/67 3I>
IEC61850
ANSI IEC
Function Enabled
in Settings
132 kV Bus
1000/5
132kV/110V
132kV/
110V
132kV/
110V
S SIMG
63
S SCBR
Cond
Function Disabled
in Settings
ANSI1000138_2_en.vsd
LMB RFLO
Monit.
ANSI IEC
IEC61850
289
ANSI11000138 V2 EN
Figure 2. A typical protection and control application for a double busbar in single breaker arrangement
Bay control REC650 ANSI
1MRK 511 265-BUS B
Product version: 1.2
ABB 5
REC650-A07A – Bus Coupler single breaker 10AI (4I+6U)
S CSWI
Control
S XCBR
Control
S CSWI
Control
S CSWI
Control
S CSWI
Control
SMP PTRC
94 1->0
S CSWI
Control
S CSWI
Control
S CSWI
Control
SES RSYN
25 SYNC
TCS SCBR
Cond
TCS SCBR
Cond
SPVN ZBAT
Cond
Other configured functions
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
S XSWI
Control
EF4 PTOC
51N
IN>
Q CBAY
Control
S SCBR
Cond
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
S CILO
Control
SEL GGIO
Control
DRP RDRE
Mont.
52
189
289
289G
189G
WA1
WA2
1189G 2189G
CC RBRF
50BF 3I> BF
PH PIOC
50 3I>>
CC RPLD
52PD PD
C MMXU
Meter.
C MSQI
Meter.
V MMXU
Meter.
V MMXU
Meter.
IEC61850
ANSI IEC
Function Enabled
in Settings
132 kV Bus
1000/5
132kV/
110V
132kV/
110V
OC4 PTOC
51/67 3I>
ANSI11000139_2_en.vsd
S SIMG
63
IEC61850
ANSI IEC
Function Disabled
in Settings
ANSI11000139 V2 EN
Figure 3. A typical protection and control application for a bus coupler in single breaker arrangement
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
6 ABB
3. Available functions
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
ABB 7
Control and monitoring functions
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
Control
SESRSYN 25 Synchrocheck, energizing check, and
synchronizing
0–1 1 1 1
SMBRREC 79 Autorecloser for 3–phase operation 0–1 1 1 1
APC8 Apparatus control for single bay, max 8
app. (1CB) incl. interlocking
1 1 1 1
SCILO 3 Logical node for interlocking 8 8 8 8
BB_ES 3 Interlocking for busbar earthing switch 3 3 3 3
A1A2_BS 3 Interlocking for bus-section breaker 2 2 2 2
A1A2_DC 3 Interlocking for bus-section
disconnector
3 3 3 3
ABC_BC 3 Interlocking for bus-coupler bay 1 1 1 1
BH_CONN 3 Interlocking for 1 1/2 breaker diameter 1 1 1 1
BH_LINE_A 3 Interlocking for 1 1/2 breaker diameter 1 1 1 1
BH_LINE_B 3 Interlocking for 1 1/2 breaker diameter 1 1 1 1
DB_BUS_A 3 Interlocking for double CB bay 1 1 1 1
DB_BUS_B 3 Interlocking for double CB bay 1 1 1 1
DB_LINE 3 Interlocking for double CB bay 1 1 1 1
ABC_LINE 3 Interlocking for line bay 1 1 1 1
AB_TRAFO 3 Interlocking for transformer bay 1 1 1 1
SCSWI Switch controller 8 8 8 8
SXCBR Circuit breaker 3 3 3 3
SXSWI Circuit switch 7 7 7 7
POS_EVAL Evaluation of position indication 8 8 8 8
SELGGIO Select release 1 1 1 1
QCBAY Bay control 1 1 1 1
LOCREM Handling of LR-switch positions 1 1 1 1
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
8 ABB
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
LOCREMCTRL LHMI control of Permitted Source To
Operate (PSTO)
1 1 1 1
SLGGIO Logic Rotating Switch for function
selection and LHMI presentation
15 15 15 15
VSGGIO Selector mini switch extension 20 20 20 20
DPGGIO IEC 61850 generic communication I/O
functions double point
16 16 16 16
SPC8GGIO Single point generic control 8 signals 5 5 5 5
AUTOBITS AutomationBits, command function for
DNP3.0
3 3 3 3
I103CMD Function commands for
IEC60870-5-103
1 1 1 1
I103IEDCMD IED commands for IEC60870-5-103 1 1 1 1
I103USRCMD Function commands user defined for
IEC60870-5-103
4 4 4 4
I103GENCMD Function commands generic for
IEC60870-5-103
50 50 50 50
I103POSCMD IED commands with position and select
for IEC60870-5-103
50 50 50 50
Secondary system supervision
CCSRDIF 87 Current circuit supervision 0–1 1 1 1
SDDRFUF Fuse failure supervision 0–1 1 1 1
TCSSCBR Breaker close/trip circuit monitoring 3 3 3 3
Logic
SMPPTRC 94 Tripping logic, common 3–phase output 1 1 1 1
TMAGGIO Trip matrix logic 12 12 12 12
OR Configurable logic blocks, OR gate 283 283 283 283
INVERTER Configurable logic blocks, Inverter gate 140 140 140 140
PULSETIMER Configurable logic blocks, Pulse timer 40 40 40 40
GATE Configurable logic blocks, Controllable
gate
40 40 40 40
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
ABB 9
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
XOR Configurable logic blocks, exclusive
OR gate
40 40 40 40
LOOPDELAY Configurable logic blocks, loop delay 40 40 40 40
TIMERSET Configurable logic blocks, timer
function block
40 40 40 40
AND Configurable logic blocks, AND gate 280 280 280 280
SRMEMORY Configurable logic blocks, set-reset
memory flip-flop gate
40 40 40 40
RSMEMORY Configurable logic blocks, reset-set
memory flip-flop gate
40 40 40 40
ANDQT Configurable logic Q/T, AND gate with
quality and time
120 120 120 120
ORQT Configurable logic Q/T, OR gate with
quality and time
120 120 120 120
INVERTERQT Configurable logic Q/T, inverter gate
with quality and time
120 120 120 120
XORQT Configurable logic Q/T, exclusive OR
gate with quality and time
40 40 40 40
SRMEMORYQT Configurable logic Q/T, set-reset with
memory flip-flop gate with quality and
time
40 40 40 40
RSMEMORYQT Configurable logic Q/T, reset-set with
memory flip-flop gate with quality and
time
40 40 40 40
TIMERSETQT Configurable logic Q/T, timer function
block with quality and time
40 40 40 40
PULSETIMERQT Configurable logic Q/T, pulse timer with
quality and time
40 40 40 40
INVALIDQT Configurable logic Q/T, used for
invalidate data
12 12 12 12
INDCOMBSPQT Configurable logic Q/T, single point
indication logic signal combinator
combining value with quality and time
20 20 20 20
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
10 ABB
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
INDEXTSPQT Configurable logic Q/T, single point
indication logic signal gate extracting
value with quality and time
20 20 20 20
Q/T Configurable logic blocks Q/T 0–1 20 20 20
FXDSIGN Fixed signal function block 1 1 1 1
B16I Boolean 16 to Integer conversion 16 16 16 16
B16IFCVI Boolean 16 to Integer conversion with
logic node representation
16 16 16 16
IB16A Integer to Boolean 16 conversion 16 16 16 16
IB16FCVB Integer to Boolean 16 conversion with
logic node representation
16 16 16 16
Monitoring
CVMMXN Measurements 6 6 6 6
CMMXU Phase current measurement 10 10 10 10
VMMXU Phase-phase voltage measurement 6 6 6 6
CMSQI Current sequence component
measurement
6 6 6 6
VMSQI Voltage sequence measurement 6 6 6 6
VNMMXU Phase-neutral voltage measurement 6 6 6 6
AISVBAS Function block for service values
presentation of the analog inputs
1 1 1 1
TM_P_P2 Function block for service values
presentation of primary analog inputs
600TRM
1 1 1 1
AM_P_P4 Function block for service values
presentation of primary analog inputs
600AIM
1 1 1 1
TM_S_P2 Function block for service values
presentation of secondary analog
inputs 600TRM
1 1 1 1
AM_S_P4 Function block for service values
presentation of secondary analog
inputs 600AIM
1 1 1 1
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
ABB 11
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
CNTGGIO Event counter 5 5 5 5
DRPRDRE Disturbance report 1 1 1 1
AxRADR Analog input signals 4 4 4 4
BxRBDR Binary input signals 6 6 6 6
SPGGIO IEC 61850 generic communication I/O
functions
64 64 64 64
SP16GGIO IEC 61850 generic communication I/O
functions 16 inputs
16 16 16 16
MVGGIO IEC 61850 generic communication I/O
functions
16 16 16 16
MVEXP Measured value expander block 66 66 66 66
LMBRFLO Fault locator 1 1 1
SPVNZBAT Station battery supervision 0–1 1 1 1
SSIMG 63 Insulation gas monitoring function 0–1 1 1 1
SSIML 71 Insulation liquid monitoring function 0–1 1 1 1
SSCBR Circuit breaker condition monitoring 0–1 1 1 1
I103MEAS Measurands for IEC60870-5-103 1 1 1 1
I103MEASUSR Measurands user defined signals for
IEC60870-5-103
3 3 3 3
I103AR Function status auto-recloser for
IEC60870-5-103
1 1 1 1
I103EF Function status ground-fault for
IEC60870-5-103
1 1 1 1
I103FLTPROT Function status fault protection for
IEC60870-5-103
1 1 1 1
I103IED IED status for IEC60870-5-103 1 1 1 1
I103SUPERV Supervison status for IEC60870-5-103 1 1 1 1
I103USRDEF Status for user defined signals for
IEC60870-5-103
20 20 20 20
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
12 ABB
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
Metering
PCGGIO Pulse counter logic 16 16 16 16
ETPMMTR Function for energy calculation and
demand handling
3 3 3 3
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
ABB 13
Back-up protection functions
IEC 61850/
Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
Current protection
PHPIOC 50 Instantaneous phase overcurrent
protection, 3–phase output
0–1 1 1 1
OC4PTOC 51 Four step phase overcurrent protection, 3–
phase output
0–1 1 1 1
EFPIOC 50N Instantaneous residual overcurrent
protection
0–1 1 1 1
EF4PTOC 51N/67N Four step residual overcurrent protection,
zero/negative sequence direction
0–1 1 1 1
SDEPSDE 67N Sensitive directional residual overcurrent
and power protection
0–1 1 1 1
LCPTTR 26 Thermal overload protection, one time
constant, Celsius
0–1 1 1 1
LFPTTR 26 Thermal overload protection, one time
constant, Fahrenheit
0–1 1 1 1
CCRBRF 50BF Breaker failure protection, 3–phase
activation and output
0–1 1 1 1
STBPTOC 50STB Stub protection 0–1 1 1 1
CCRPLD 52PD Pole discordance protection 0–1 1 1 1
BRCPTOC 46 Broken conductor check 0–1 1 1 1
GUPPDUP 37 Directional underpower protection 0–1 1 1 1
GOPPDOP 32 Directional overpower protection 0–1 1 1 1
DNSPTOC 46 Negative sequence based overcurrent
function
0–1 1 1 1
Voltage protection
UV2PTUV 27 Two step undervoltage protection 0–1 1 1 1
OV2PTOV 59 Two step overvoltage protection 0–1 1 1 1
ROV2PTOV 59N Two step residual overvoltage protection 0–1 1 1 1
LOVPTUV 27 Loss of voltage check 0–1 1 1 1
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
14 ABB
IEC 61850/
Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
Frequency protection
SAPTUF 81 Underfrequency function 0–2 2 2 2
SAPTOF 81 Overfrequency function 0–2 2 2 2
SAPFRC 81 Rate-of-change frequency protection 0–2 2 2 2
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
ABB 15
Communication
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
Station communication
IEC61850-8-1 IEC 61850 communication protocol 1 1 1 1
DNPGEN DNP3.0 for TCP/IP communication
protocol
1 1 1 1
RS485DNP DNP3.0 for EIA-485
communication protocol
1 1 1 1
CH1TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
CH2TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
CH3TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
CH4TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
OPTICALDNP DNP3.0 for optical serial
communication
1 1 1 1
MSTSERIAL DNP3.0 for serial communication
protocol
1 1 1 1
MST1TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
MST2TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
MST3TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
MST4TCP DNP3.0 for TCP/IP communication
protocol
1 1 1 1
RS485GEN RS485 1 1 1 1
OPTICALPROT Operation selection for optical serial 1 1 1 1
RS485PROT Operation selection for RS485 1 1 1 1
DNPFREC DNP3.0 fault records for TCP/IP
communication protocol
1 1 1 1
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
16 ABB
IEC 61850/Function
block name
ANSI Function description Bay
REC650
REC650 (A01A)
1CBA
REC650 (A02A)
1CBAB
REC650 (A07A)
BCAB
OPTICAL103 IEC60870-5-103 Optical serial
communication
1 1 1 1
RS485103 IEC60870-5-103 serial
communication for RS485
1 1 1 1
GOOSEINTLKRCV Horizontal communication via
GOOSE for interlocking
59 59 59 59
GOOSEBINRCV GOOSE binary receive 4 4 4 4
ETHFRNT
ETHLAN1
GATEWAY
Ethernet configuration of front port,
LAN1 port and gateway
1 1 1 1
GOOSEDPRCV GOOSE function block to receive a
double point value
32 32 32 32
GOOSEINTRCV GOOSE function block to receive
an integer value
32 32 32 32
GOOSEMVRCV GOOSE function block to receive a
measurand value
16 16 16 16
GOOSESPRCV GOOSE function block to receive a
single point value
64 64 64 64
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
ABB 17
Basic IED functions
IEC 61850/Function
block name
Function description
Basic functions included in all products
INTERRSIG Self supervision with internal event list 1
SELFSUPEVLST Self supervision with internal event list 1
TIMESYNCHGEN Time synchronization 1
SNTP Time synchronization 1
DTSBEGIN, DTSEND,
TIMEZONE
Time synchronization, daylight saving 1
IRIG-B Time synchronization 1
SETGRPS Setting group handling 1
ACTVGRP Parameter setting groups 1
TESTMODE Test mode functionality 1
CHNGLCK Change lock function 1
TERMINALID IED identifiers 1
PRODINF Product information 1
SYSTEMTIME System time 1
RUNTIME IED Runtime comp 1
PRIMVAL Primary system values 1
SMAI_20_1 -
SMAI_20_12
Signal matrix for analog inputs 2
3PHSUM Summation block 3 phase 12
GBASVAL Global base values for settings 6
ATHSTAT Authority status 1
ATHCHCK Authority check 1
SPACOMMMAP SPA communication mapping 1
FTPACCS FTP access with password 1
DOSFRNT Denial of service, frame rate control for front port 1
DOSLAN1 Denial of service, frame rate control for LAN1 1
DOSSCKT Denial of service, socket flow control 1
SAFEFILECOPY Safe file copy function 1
SPATD Date and time via SPA protocol 1
BCSCONF Basic communication system 1
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
18 ABB
4. Control
Synchrocheck, energizing check, and
synchronizing SESRSYN (25)
The Synchronizing function allows closing of
asynchronous networks at the correct moment
including the breaker closing time, which improves
the network stability.
Synchrocheck, energizing check, and synchronizing
(SESRSYN, 25) function checks that the voltages on
both sides of the circuit breaker are in synchronism,
or with at least one side dead to ensure that closing
can be done safely.
SESRSYN (25) function includes a built-in voltage
selection scheme for double bus and breaker-and-a-
half or ring busbar arrangements.
Manual closing as well as automatic reclosing can
be checked by the function and can have different
settings.
For systems which are running asynchronous a
synchronizing function is provided. The main
purpose of the synchronizing function is to provide
controlled closing of circuit breakers when two
asynchronous systems are going to be connected.
It is used for slip frequencies that are larger than
those for synchronism check and lower than a set
maximum level for the synchronizing function.
Autorecloser for 3-phase operation (79)
The autorecloser SMBRREC, 79 function provides
high-speed and/or delayed auto-reclosing for single
breaker applications.
Up to five three-phase reclosing attempts can be
included by parameter setting.
The autoreclosing function can be configured to co-
operate with a synchronism check function.
Apparatus control APC
The apparatus control functions are used for control
and supervision of circuit breakers, disconnectors
and grounding switches within a bay. Permission to
operate is given after evaluation of conditions from
other functions such as interlocking, synchronism
check, operator place selection and external or
internal blockings.
Apparatus control features:
• Select-Execute principle to give high reliability
• Selection function to prevent simultaneous
operation
• Selection and supervision of operator place
• Command supervision
• Block/deblock of operation
• Block/deblock of updating of position indications
• Substitution of position indications
• Overriding of interlocking functions
• Overriding of synchrocheck
• Operation counter
• Suppression of Mid position
Two types of command models can be used:
• Direct with normal security
• SBO (Select-Before-Operate) with enhanced
security
Direct commands are received with no prior select
command. SBO commands are received with a
select command first and on successful selection, a
proceeding operate command.
In normal security, the command is processed and
the resulting position is not supervised. However
with enhanced security, the command is processed
and the resulting position is supervised.
Control operation can be performed from the local
HMI under authority control if so defined.
Bay control REC650 ANSI 1MRK 511 265-BUS B
Product version: 1.2
ABB 19
ANSI09000668-1-en.vsd
ANSI09000668 V1 EN
Figure 4. Select before operation with confirmation of
command
Cancel
Ok
ANSI09000669-1-en.vsd
ANSI09000669 V1 EN
Figure 5. Overriding of synchrocheck
Bay control QCBAY
The Bay control QCBAY function is used together
with Local remote and local remote control
functions to handle the selection of the operator
place per bay. QCBAY also provides blocking
functions that can be distributed to different
apparatuses within the bay.
Local remote LOCREM /Local remote control
LOCREMCTRL
The signals from the local HMI or from an external
local/remote switch are applied via the function
blocks LOCREM and LOCREMCTRL to the Bay
control (QCBAY) function block. A parameter in
function block LOCREM is set to choose if the
switch signals are coming from the local HMI or
from an external hardware switch connected via
binary inputs.
Interlocking
The interlocking functionality blocks the possibility
to operate high-voltage switching devices, for
instance when a disconnector is under load, in
order to prevent material damage and/or accidental
human injury.
Each control IED has interlocking functions for
different switchyard arrangements, each handling
the interlocking of one bay. The interlocking
functionality in each IED is not dependent on any
central function. For the station-wide interlocking,
the IEDs communicate via the station bus or by
using hard wired binary inputs/outputs.
The interlocking conditions depend on the primary
bus configuration and status of any breaker or
switch at any given time.
Logic rotating switch for function selection and
LHMI presentation SLGGIO
The logic rotating switch for function selection and
LHMI presentation (SLGGIO) (or the selector switch
function block) is used to get a selector switch
functionality similar to the one provided by a
hardware selector switch. Hardware selector
switches are used extensively by utilities, in order to
have different functions operating on pre-set values.
Hardware switches are however sources for
maintenance issues, lower system reliability and an
extended purchase portfolio. The logic selector
switches eliminate all these problems.
Selector mini switch VSGGIO
The Selector mini switch VSGGIO function block is
a multipurpose function used for a variety of
applications, as a general purpose switch.
Bay control REC650 ANSI
1MRK 511 265-BUS B
Product version: 1.2
20 ABB
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109

ABB REC650 ANSI User manual

ABB
Brand
ABB
Model
REC650 ANSI
Category
Measuring, testing & control
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents