Page is loading ...
Manual version: 6PW101-20170411 BOM: 3123A19Y
i
H3C LSUM1FWCEAB0 firewall card
1 Card identifier
The card identifier LSUM1FWCEAB0 is at the upper right corner of the front panel.
2 Introduction
The LSUM1FWCEAB0 card is a 10-Gbps high performance firewall card that provides functions
including firewall, VPN, content filtering, and NAT. You can install it on an H3C S10500 or S7500E
switch to improve security capabilities of the switch without changing the network topology.
3 Specifications
The card has one console port, two USB ports, and two GE combo interfaces.
Figure 1 Front panel of the LSUM1FWCEAB0 firewall card
(1) Console port (CONSOLE) (2) USB ports (reserved)
(3) 10/100/1000BASE-T copper combo port
(4) Copper
combo port
LED (LINK/ACT)
(5) 1000BASE-X fiber combo port (6) Fiber combo port
LED (LINK/ACT)
(7) Alarm LED (ALM) (8) System LED (RUN)
(9) Ejector lever (10)
Captive screw
Table 1 Card specifications
Item S
p
ecification
Flash 8 MB Nor Flash
Memory
One memory slot
Standard configuration: 8 GB (one 8-GB DDR3
SDRAM)
CF card slot
One built-in CF card slot
Standard configuration: 4 GB
Maximum configuration: 4 GB
Dimensions (H × W × D) 40.1 × 399.2 × 376.8 mm (1.58 × 15.71 × 14.83 in)
Power consumption 109.0 W to 157.1 W
Weight 3.9 kg (12.79 lb)
Hot swapping Supported
Manual version: 6PW101-20170411 BOM: 3123A19Y
ii
Item S
p
ecification
Interfaces
• 1 console port
• 2 USB ports (reserved)
• 2 combo interfaces. A combo interface is a logical
interface that contains one 1000BASE-X SFP fiber
port and one 10/100/1000Base-T copper port.
The two ports share one interface view and cannot
work simultaneously. When you use the combo
enable { copper | fiber } command to enable one
port, the other port is disabled automatically.
CAUTION:
Keep the dust plug installed on the unused SFP port.
Ambient temperature
• Operating: 0°C to 45°C (32°F to 113°F)
• Storage: –40°C to +70°C (–40°F to +158°F)
Ambient humidity
• Operating: 10% RH to 95% RH, noncondensing
• Storage: 5% RH to 95% RH, noncondensing
Compatible gateway models and slots
• H3C S10500 switches (The quantity requirement
for this card varies by switch model.)
• S7500E switches (The quantity requirement for this
card varies by switch model.)
NOTE:
To verify compatibility of the card with the software release you are using, see the release notes.
Table 2 Console port specifications
Item S
p
ecification
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
Services
• Provides connection to an ASCII terminal.
• Provides connection to the serial port of a local or
remote (through a pair of modems) PC running
terminal emulation program.
• Supports command line interface (CLI)
Table 3 10/100/1000BASE-T copper Ethernet port specifications
Item S
p
ecification
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Supported cable Category-5 (or above) twisted pair cable
Manual version: 6PW101-20170411 BOM: 3123A19Y
iii
Item S
p
ecification
Transmission distance 100 m (328.08 ft)
Port transmission rate
• 10 Mbps, half/full duplex
• 100 Mbps, half/full duplex
• 1000 Mbps, full duplex
Table 4 1000BASE-X fiber port specifications
Item S
p
ecification
Transceiver module SFP
Connector type LC
Interface standard 802.3, 802.3u, and 802.3ab
Operating mode 1000 Mbps, full duplex
Table 5 1000BASE-X SFP port specifications
Gigabit SFP module
Central
wavelength
Connector
Cable specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A 850 nm LC
62.5/125μm
multi-mode optical fiber
0.55 km (0.34 miles)
SFP-GE-LX-SM1310-A 1310 nm LC
9/125 μm single-mode
optical fiber
10 km (6.21 miles)
SFP-GE-LH40-SM1310 1310 nm LC
9/125 μm single-mode
optical fiber
40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 nm LC
9/125 μm single-mode
optical fiber
40 km (24.86 miles)
SFP-GE-LH80-SM1550 1550 nm LC
9/125 μm single-mode
optical fiber
80 km (49.71 miles)
SFP-GE-LH100-SM1550 1550 nm LC
9/125 μm single-mode
optical fiber
100 km (62.14 miles)
4 LEDs
The card provides LEDs to show the operating status of the card and the interfaces.
Table 6 LED description
LED Status Descri
p
tion
Alarm LED (ALM)
Off The system is operating correctly.
Steady red
A serious failure has occurred. Read the system log for
troubleshooting.
Manual version: 6PW101-20170411 BOM: 3123A19Y
iv
LED Status Descri
p
tion
System LED (RUN)
Off No power input or the firewall card is faulty.
Steady green The system is not operating correctly.
Flashing green (1 Hz) The system has started up and is operating correctly.
Flashing green (8 Hz) The system is loading the software.
Combo interface LED
(LINK/ACT)
Off No link is present on the port.
Steady green A link is present on the port.
Flashing green The port is sending or receiving data.
5 Installing and removing the card
CAUTION:
• Wear a reliably-grounded ESD wrist strap before you install or remove the firewall card.
• Do not touch the components on the PCB.
The slots on the H3C S10500 switches are either horizontally oriented or vertically oriented. When
installing the card in a horizontal slot, make sure its PCB faces up. When installing the card in a vertical
slot, make sure its PCB faces left.
This section uses a vertically oriented card to describe the installation and removal procedures.
5.1
Installing the card
1. Remove the blank panel from the slot for the card at the front of the switch.
This manual uses slot 9 as an example.
2. Place the card vertically with the surface-mounted components facing left. Pull outward the ejector
levers and gently push the card in along the slot guide rails until the card is in close contact with
the backplane.
3. Push the ejector levers inward.
4. Tighten the captive screws with a Phillips screwdriver to secure the card in the slot.
Manual version: 6PW101-20170411 BOM: 3123A19Y
v
Figure 2 Installing an LSUM1FWCEAB0 firewall card
5.2
Removing the card
1. Use a Phillips screwdriver to loosen the captive screws at both sides of the card until all pressure
is released.
2. Pull the ejector levers at both sides of the card outward, and pull the card along the guide rails until
it completely comes out of the backplane.
3. Place the card on an anti-static workbench with the surface-mounted components up, or put it in an
anti-static bag.
4. If no new card is to be installed, install a filler panel to prevent dust and ensure good ventilation in
the switch.
6 Software upgrade
The LSUM1FWCEAB0 card has an independent operating system and CLI. To upgrade the card
software, you must access its CLI or Boot menu after logging in to the card through its console port or
management Ethernet port. For information about upgrading the LSUM1FWCEAB0 firewall card, see the
release notes.
Manual version: 6PW101-20170411 BOM: 3123A19Y
vi
7 Obtaining documentation
To access the most up-to-date H3C product documentation on the H3C website at www.h3c.com.hk:
1. Go to http://www.h3c.com.hk/Technical_Documents.
2. Click Security Products, and then choose the desired product.
Copyright © 2017 New H3C Technologies Co., Ltd.
/