2. Midmark
  3. Procenter Systems
Procenter Systems

Midmark Procenter Systems Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Midmark Procenter Systems Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
© Midmark Corporation 2001 SF-1812 1
12:00 PRE-INSTALLATION
CASEWORK PLACEMENT
Be sure dimensional requirements are met before
installing air and water connections. See Figure 1.
CONTENTS Page
Casework Placement....................................1
Connections Diagram...................................2
Water Supply Requirements........................3
Air Supply Requirements.............................3
Vacuum Requirements.................................3
NOTE
Verify desired location with proper personnel before
installing required connections.
KA998700i
Figure 1. 12:00 Free-Standing Casework Dimensions
43.25 in.
(109.9 cm)
22.75 in.
(57.9 cm)
47.25 in.
(120 cm)
or
52.25 in.
(132.7 cm)
19 in.
(48.3 cm)
20 in.
(50.8 cm)
42.5 in.
(108 cm)
4.5 in.
(11.4 cm)
55.6 in.
(141.1 cm)
or
44.8 in.
(113.8 cm)
72.6 in.
(184.3 cm)
or
61.8 in.
(157 cm)
32.6 in.
(82.7 cm)
22.6 in.
(57.5 cm)
31.1 in.
(78.9 cm)
16.9 in.
(42.9 cm)
21.5 in.
(54.6 cm)
20 in.
(50.8 cm)
or
9.25 in.
(23.5 cm)
003-1269-00 Rev. A (10/01)
12:00 Delivery Unit / Asst.’s Instruments
Pre-Installation Guide
PRE-INSTALLATION
12:00 PRE-INSTALLATION
Style A
© Midmark Corporation 2001 SF-1812 2
12:00 PRE-INSTALLATION
CONNECTIONS DIAGRAM
Figure 4. Plumbing / Electrical Connections Diagram
NOTE
Install all utilities according to local codes and regula-
tions. Contact a licensed plumber & electrician for
installation.
Water Supply
Air Supply
Vacuum Supply
Cabinet
Electrical Terminal
Box
Outlets
Fuse
Electrical Supply
120 VAC / 20 amp / 60 Hz
3 wire, Dedicated Circuit
Top View of Base
Front
RH side plumbing “rough-in”
perimeter
Finished Floor
Water
Air
Vacuum
Rev. 11/00
Return to Module Table of Contents
© Midmark Corporation 2001 SF-1812 3
12:00 PRE-INSTALLATION
WATER SUPPLY REQUIREMENTS
1/2 in. (13 mm) pipe NPT (supplied by contractor) protrud-
ing 2.0 to 2.5 in. (5.1 to 6.3 cm) above finished surface of
floor. Manual shut-off valve (supplied by Midmark) to be
installed by contractor.
Water pressure must be 30-50 (max.) PSI at the shut-off
valve. Flush water plumbing clean before making final
connections to dental equipment.
AIR SUPPLY REQUIREMENTS
1/2 in. (13 mm) pipe NPT (supplied by contractor) protrud-
ing 2.0 to 2.5 in. (5.1 to 6.3 cm) above finished surface of
floor. Manual shut-off valve (supplied by Midmark) to be
installed by contractor.
Air pressure must be 70-100 (max.) PSI at the shut-off
valve. Flush air plumbing clean before making final con-
nections to dental equipment.
VACUUM REQUIREMENTS
(Assistant’s Instrument Units only)
Plumbing to junction box should be specified by central
vacuum supplier and terminated in junction box with
5/8 in. (16 mm) O.D. tube protruding 2.0 to 2.5 in. (5.1 to
6.3 cm) above finished surface of floor.
Return to Module Table of Contents
© Midmark Corporation 2001 SF-1812 4
12:00 PRE-INSTALLATION
Return to Module Table of Contents
/