MULTIPLEX XP3 / XP4 Operating instructions

Brand: MULTIPLEX

Model: XP3 / XP4

Type: Operating instructions

MULTIPLEX XP3 / XP4 is a pre-mix, remote carb, and cold carbonator counter dispense unit designed for cooling and recirculating syrups, carbonated water, and still water to provide the correct conditioning for serving draught soft drinks. Some of its key capabilities and possible use cases include:

Cooling and recirculating syrups, carbonated water, and still water.
Maintaining the correct conditioning for serving draft soft drinks.
Carbonating water using an integral carbonator (Cold Carb versions) or a remote carbonator.
Dispensing carbonated soft drinks through dispense valves.
Setting the brix to the drink manufacturer's specification.

Cooling and recirculating syrups, carbonated water, and still water.
Maintaining the correct conditioning for serving draft soft drinks.
Carbonating water using an integral carbonator (Cold Carb versions) or a remote carbonator.
Dispensing carbonated soft drinks through dispense valves.
Setting the brix to the drink manufacturer's specification.

ÿþ üû úþ

 û

XP3 / XP4 PRE-MIX, REMOTE

CARB, COLD CARB OVER

COUNTER DISPENSE UNITS

INSTALLATION &

OPERATION INSTRUCTIONS

WDE INS 37 ISSUE 2

APPROVED BY GARY WYATT

DATED 1st June 1997

XP3 / XP4 PRE-MIX, REMOTE CARB, ANDXP3 / XP4 PRE-MIX, REMOTE CARB, AND

XP3 / XP4 PRE-MIX, REMOTE CARB, AND

COLD CARBONATOR COUNTER DISPENSE UNIT.COLD CARBONATOR COUNTER DISPENSE UNIT.

COLD CARBONATOR COUNTER DISPENSE UNIT.

(UK & EXPORT)(UK & EXPORT)

(UK & EXPORT)

INSTALLATION & OPERATION INSTRUCTIONSINSTALLATION & OPERATION INSTRUCTIONS

INSTALLATION & OPERATION INSTRUCTIONS

NOTE: Please read instructions fully before commencing any work on this equipment.

NOTE: The unit should be installed and serviced by a suitably trained person.

NOTE: Sealed plugs may be fitted to new units.

Installation ProcedureInstallation Procedure

Installation Procedure

Unpack theunitfromitstransportationpacking and visually check for any signs of damage.

Site the dispenser in the desired location, allowing for a free circulation of air, and the

followingservices:-

a Mains Electricity Supply. (within 2 metres).

b Filtered water supply with shut off valve.(Cold carb only).

cCo

Gas supply (Remote carb only).

d Syrupsupply.

eCo

Gas supply (Carbonator).

fCo

Gas supply (Gas Pumps) if fitted. (XP4 only).

Allowancemustalsobemadeforthedriptraydrain(Iffitted).RoutedtoasuitabledrainNOT

a waste container.

The unit should be fitted with a correctly wired and fused 13 amp plug fitted with a 10 amp

fuse, or alternatively a standard Euro plug to IEC 83: 1975.

Removetopcoverscrew.Liftupcoveranddisconnect(iffitted)theadvertisingpanelwiring

from electrical box. Remove cover completely. Remove front panel by loosening (not

removing)the fixing screws.

Fill the water bath, via removable cap with fresh clean water, to over-flow level.

Ensurecarbonatorisolateswitchisintheoffposition.(Location:XP3- TopofelectricBox,

XP4 - Top of fan shroud.)

Connect unit to the Mains Electricity Supply (do not turn on yet).

Switchontheunitatthemainsplugandallowice-banktostartbuilding.(Therewillbeadelay

of approx. 4 mins on the XP4 due to the electronic control.)

Connect Co

Gas supply to carbonator and set to 70-80 psi (4.8 - 5.4 bar) (Cold carb only).

Connect Co

Gas supply to gas pumps (if fitted, XP4 only) and set to 50 psi (3.3 bar)

ConnectupfilteredwatersupplytocarbonatorPumpandsetto40-5-psi(2.8-3.3bar)(Cold

Carb only)

Connect remaining products as labelled.

Turnongastocarbonatorandventoffbypullingortwistingringpulloncarbonatortop.(cold

carb only).

Turn on water supply.

Switch on carbonator control. The carbonator pump should now run for approx. 30 sec. and

stop.Thecarbonatorisnowfullandreadyforuse.However,shouldtheLEDilluminatethere

are one or two causes:

1 UK only. LED flashes at fast rate. There is an incorrect connection to the unit on

either live, neutral or earth. The unit must be switched off at the plug and the fault

checked and corrected. Reset by switching off then on again.

2 LED flashes at slow rate after carbonator pump has run for up to 5 mins. This

indicates there is an inadequate water supply to the pump and should be

investigated before resetting control. Reset by switching control off then on.

Switch on dispense valves via the key-switch on the right hand side of base and purge each

valve independently. The brix can now be set to the drink manufacturers specification.

Check for obvious leaks.

Refit front panel.

Switch off unit at mains plug, and refit top cover, reconnecting advertising panel if fitted.

Switch unit on again at mains plug, and allow ice-bank to build fully. (There will be a delay

of approx. 4 mins on the XP4.)

Ways the Equipment should not be used.Ways the Equipment should not be used.

Ways the Equipment should not be used.

ThisunitisintendedforuseasaCoolingandrecirculatingunitforSyrups,CarbonatedWater,

Still Water to provide the correct conditioning for serving Draught Soft Drinks and as such

should only be used for that purpose. There are NO other recommended uses for this

Equipment.

The carbonator on the Cold Carb versions is integral, otherwise a remote carbonator is used

therefore itshouldbenotedthatthe Carbonation Process involves the use of High Pressures

andapotentially noxiousgasandassuch duecareshould betaken whenhandling,installing

and maintaining the equipment with particular regard to these hazards.

CarbonDioxideleaksarepotentiallyfatalifconcentrations risetodangerouslevels,in view

ofthisinstallationsshouldberegularlycheckedforintegrityandthegeneralareaofinstallation

properly ventilated at all times.

Theweightofthisunitissuchthatitcanbeliftedtoarelativelysafeheightof24"utilisingtwo

people otherwise a Mechanical Lifting Device should be used.

Units Weight.Units Weight.

Units Weight.

XP3PRE/Remote XP3Cold/Carb XP4

kg 41.0 54.5 66.4

Lbs (Dry) 90 120 146

WARNING: THIS EQUIPMENT MUST BE EARTHED

IMPORTANT.IMPORTANT.

IMPORTANT.

The Wires in this Mains Lead are Coloured in accordance with the following Code:

Green and Yellow Earth.

Blue Neutral.

Brown Live

AstheColoursoftheWiresintheMainsLeadofthisAppliancemaynotcorrespondwiththe

Coloured Markings identifying the Terminals in the Plug to be fitted proceed as follows:

a The Wire which is Coloured Green and Yellow MUST be connected to the terminal

in the Plug that is marked with the letter ‘E’ or by the earth symbol

or coloured Green or Green and Yellow.

b The Wire which is Coloured Blue MUST be connected to the Terminal in the Plug

that is marked with the letter ‘N’ or Coloured Black.

c The Wire which is Coloured Brown MUST be connected to the Terminal in the

Plug that is marked with the letter ‘L’ or Coloured Red.

Dismantling / Decommissioning Procedure.Dismantling / Decommissioning Procedure.

Dismantling / Decommissioning Procedure.

a Isolate the Unit from Mains Water Supply.

b Isolate Product supply from Unit.

c Drain the system by opening the Dispense Valve until no more water flows.

d Isolate the unit from the Carbon Dioxide Supply (turn off the Gas Bottle Valve).

e Vent Pressure from Lines by opening Product Tap.

f Isolate the unit from Mains Electricity Supply.

g Disconnect the Supply and Product Lines.

h Syphon or pump out Water from Water bath.

i Allow ice bank to melt (the careful use of hot water may be used to accelerate this

process.)

j Syphon or Pump out remaining water from Bath.

WARNING: FAILURE TO REMOVE ALL ICE / WATER COULD RESULT IN

SUBSTANTIAL AMOUNTS OF WATER BEING RELEASED FROM

THEUNITWHICHMAYBEDETRIMENTALTOTHEUNITAND/OR

ITS SURROUNDINGS AND INCREASE THE MAXIMUM WEIGHT

OF THE UNIT.

Adjustment / Maintenance Requirements.Adjustment / Maintenance Requirements.

Adjustment / Maintenance Requirements.

ItisnotrecommendedthattheEndUsermakesanyadjustmentsorcarriesoutanyMaintenance

otherthan:

a Check the Mains lead and plug Visually for condition.

b Check the Unit and its pipework for evidence of leaks visually.

c Check that the condenser grill and vents are not choked or obscured .

NOTE: THERE ARE NO USER SERVICEABLE PARTS.

Methods of Cleaning.Methods of Cleaning.

Methods of Cleaning.

NOTE: PersonsperformingCleansing/SanitizingoperationsMUSTbecompetent and

fully trained in safe methods of use of Cleansing / Sanitizing Agents and their

applications.

NOTE: PERSONAL PROTECTIVE EQUIPMENT SHOULD ALWAYS BE USED.

NOTE: DO NOT USE A WATER OR STEAM HOSE TO CLEAN THE UNIT

WHILST STILL INSTALLED.

NOTE: IT IS IMPORTANT THAT ALL THE VENTS AND GRILLS ARE KEPT

CLEAR (inc: Condenser grills where applicable)

NOTE: IF THE UNIT IS FITTED WITH SOFT DRINK COILS ONLY THE

FOLLOWINGSHOULD BECARRIED OUTON ALL THEAPPROPRIATE

AREAS OF THE UNIT.

NOTE: Driptrays,nozzles,taps,shouldbewashedusingwarmwateronadailybasisby

the end user.

Weekly:Weekly:

Weekly: By End User.

a Isolate unit from Mains Electricity Supply.

b Clean sanitise the units cooling coils and product lines using Proprietary

Cleanser / Sanitiser of the Alkaline Hypochlorite type in accordance with the

Manufacturersrecommendations.

c Wipe units external casing with moist / damp cloth.

Annually:Annually:

Annually: By a Competent Service / Maintenance Engineer.

a Isolate unit from Mains Electricity Supply.

b Remove any extraneous debris from the unit or its casing preferably using a

Vacuum cleaner or brush.

c Check unit for electrical safety.

Instructions For Safe Use Of Carbon DioxideInstructions For Safe Use Of Carbon Dioxide

Instructions For Safe Use Of Carbon Dioxide

See Carbon Dioxide warning notice at rear of booklet.

Power Isolation Method.Power Isolation Method.

Power Isolation Method.

The unit is fitted with a single phase 3 pin 13 amp plug fitted with a (state fuse size of

unit) amp fuse or alternatively a standard Euro Plug to IEC83:1975.

a Switch off the socket that the plug is installed in to.

b Remove the plug from the socket.

Prevention of Freezing / Action required if Freezing occurs.Prevention of Freezing / Action required if Freezing occurs.

Prevention of Freezing / Action required if Freezing occurs.

ItisrecommendedthattheunitissitedInsuchawayasnottoexposeittotemperatureslikely

tocausefreezingi.e.below0degC. IftheUnitistobesitedinanunheatedareathenitwould

bewisetoinsulateallpipeworkandprovidesomeformofEmergencyHeatingwhichshould

be controlled by a Frost Stat. and sited in the close proximity to the Unit.

In the event of Freezing Up occurring the following action is recommended:-

a Switch off carbonator control.

b Isolate product supply to unit.

c Isolate water supply to unit.

d Drain the system by opening the Dispense Valve until no more water flows.

e Isolate the unit from the Carbon Dioxide Supply (turn off the Gas Bottle Valve).

f Vent Pressure from Lines by opening Product Tap.

g Isolate electrical supply to unit.

h Apply gentle warmth to the general area of the unit and its pipework.

i Check for obvious leaks.

j Turn on carbon dioxide supply whilst continually watching for leaks.

k Turn water supply on whilst continually watching for leaks.

l ReconnectMains Electricity supply.

m Switch on carbonator control.

n Reconnect product supply.

o Vent carbonator if fitted.

p Observe unit running for a short period watching out for Leaks, Strange noises or

any other form of malfunction, if no problems are observed then normal operation

of the unit may be resumed.

Max. / Min. Ambient Temperatures.Max. / Min. Ambient Temperatures.

Max. / Min. Ambient Temperatures.

Minimum 10 deg. C

Maximum 32 deg. C

Max. / Min. Water Pressures.Max. / Min. Water Pressures.

Max. / Min. Water Pressures.

Minimum 1.0 Bar (15 psi)

Maximum 3.3 Bar (50 psi)

Max. / Min. Carbon Dioxide Pressures.Max. / Min. Carbon Dioxide Pressures.

Max. / Min. Carbon Dioxide Pressures.

Minimum 4.8 Bar (70 psi)

Maximum 5.4 Bar (80 psi)

WARNING: Pump pressure to Carbonator Bowl 13.2 Bar (200 psi).

WARNING: Maximum Product Pressure 4.2 Bar (60 psi)

WARNING: THISEQUIPMENTCANCONTRIBUTETOTHEAMBIENT

TEMPERATURE.

WARNING: THIS UNIT IS UNSUITABLE FOR USE BY

UNSUPERVISED CHILDREN AGED OR INFIRM

PERSONS.

ADJUSTMENT PROCEDURE CODED AUTOSET PORTIONADJUSTMENT PROCEDURE CODED AUTOSET PORTION

ADJUSTMENT PROCEDURE CODED AUTOSET PORTION

CONTROL WITH TOP OFF FEATURE.CONTROL WITH TOP OFF FEATURE.

CONTROL WITH TOP OFF FEATURE.

NEW INSTALL PROCEDURE:NEW INSTALL PROCEDURE:

NEW INSTALL PROCEDURE:

1 Simultaneously, press and hold push button switches on Coded Autoset

portion Control Module until LED light in centre of module starts blinking, then

release switches. Blinking LED indicates set mode is active.

2 Put desired amount of ice in cup, place cup under valve and push selected size

button (small, medium, large, or extra large). Hold button in until cup fills to

desired portion then release button.

3 Wait for foam to settle then actuate button again to top off.

4 Repeat steps 2 and 3 for remaining drink sizes.

5 After programming all drinks sizes, press and release "CANCEL/POUR" to

return the Coded Autoset Portion Control to the operational mode. Blinking LED

light will go out.

6 Repeat steps 1 thru 5 for remaining valves.

ALTERNATE PROCEDURE:ALTERNATE PROCEDURE:

ALTERNATE PROCEDURE:

NOTE: IF TOPOFFISNOTDESIREDOR REQUIRED, THE FOLLOWING STEPS

MUST BE FOLLOWED:

a Follow steps 1 and 2

b Repeat step 2 for remaining drink sizes.

c After actuating the last selected size button, momentarily actuate one of the other

size buttons. This will signal the microprocessor that all selected sizes are

completed. Failure to do this will signal an incomplete response back to the

microprocessor and the last selected size will revert back to its previous program.

d Repeat steps a, b and c for remaining valves.

TO CHANGE DISPENSE SIZE:TO CHANGE DISPENSE SIZE:

TO CHANGE DISPENSE SIZE:

Use one of the above procedures; it is not necessary to reprogram every size.

TO ADD OR DELETE THE TOP OFF FEATURE:TO ADD OR DELETE THE TOP OFF FEATURE:

TO ADD OR DELETE THE TOP OFF FEATURE:

Use the new install procedure to add; use the alternate procedure to delete.

CANCEL/POUR:CANCEL/POUR:

CANCEL/POUR:

1 Push and release to cancel or stop valve dispensing;

2 Push and hold for continuous pour;

The portion control has a full memory retention when programming and in case of power

failure.

XP3 Pre-Mix and Post-Mix Overcounter Dispenser Parts ListXP3 Pre-Mix and Post-Mix Overcounter Dispenser Parts List

XP3 Pre-Mix and Post-Mix Overcounter Dispenser Parts List

ITEM No. W.D.E. PART No. DESCRIPTION

1 MMCP39046-13 Base Assembly - Blue

2 MMCP39046 Base Assembly - Stainless Steel

3 OP74466 Power Lead - 13 Amp Plug

4 OP74467 Power Lead - Euro Plug

5 SACACP-P01B 5P Pre-Mix Coil Assembly

6 SACACP-40966 5P Post-Mix Coil Assembly

7 SACACP-CA03 5P Post-Mix Coil Assembly - Still Option

8 SACACP-CA04 4P Post-Mix Coil Assembly

9 SACACP-40983 4P Post-Mix Coil Assembly - Still Option

10 MMCP39410B Top Cover Assembly - Blue

11 MMCP39410 Top Cover Assembly - Stainless Steel

12 SACP40007 Fridge Deck Assembly

13 CM73429 Compressor Danfoss FR11G

CM74198 Compressor Electrolux GP12TB

14 OP71729 Overload Relay Danfoss FR11G

PI41613 Relay & Capacitor Electrolux GP12TB

15 OP71548 Capacitor Danfoss FR11G

16 OP73484 Drier

17 CN73820 Condenser

18 OP73807 Fan Blade

19 SA40978 Fan Motor Assembly

20 MMAY39185 Fan Mounting Bracket

21 SA40979 Agitator Motor Assembly

22 MMEY39469 Agitator Mounting Plate

23 OP71924 Shaft washers

24 OP73625 Propellor

25 OP72956 Ice Bank Control - Mechanical

26 OP73823 Transformer

27 OP74613 Key Switch Loom

28 MMCP39703 5P Pre-Mix Valve Plate

29 MMCP40138 5P Post-Mix Valve Plate

30 MMCP39722 4P Post-Mix Valve Plate

31 83377-1 Dole Fast Flow Electric Valve

32 12-0040 Lancer Electric Valve

33 12-0060 Flomatic 424 Electric Valve

34 12-0060-01 Flomatic 424 Valve Block

35 10-0021 Pre-Mix Manual Valve - Yoke

36 10-0031 Pre-Mix Manual Valve - Flare

37 OP74391 Valve Screws

38 OP74471 Plastic Drip Tray

39 MMCP39418 Drip Tray Support

40 MMCP39447 5P Cup Rest

41 MMCP39945 4P Cup Rest

42 OP73718 Filler Plug

43 SA40984 Plastic Foot Assembly

44 OP71404 Lighting Tube

45 OP71411 Starter

SA40016 Lighting Pod - Pepsi-Cola

SA40015 Lighting Pod - Coca-Cola

SA40025 Lighting Pod - White Lens

XP4 Post-Mix Cold Carbonation Overcounter Dispenser Parts ListXP4 Post-Mix Cold Carbonation Overcounter Dispenser Parts List

XP4 Post-Mix Cold Carbonation Overcounter Dispenser Parts List

ITEM NO. W.D.E. PART No. DESCRIPTION

1 SA40224 Base Assembly - Stainless Steel

2 OP74466 Power Lead - 13 Amp Plug

3 OP74467 Power Lead - Euro Plug

4 SACACR-J02 5P C. C. Product Coil Assy. (No Pumps)

5 SACACR-J01 6P C. C. Product Coil Assy. (No Pumps)

6 SACACR-J01/P 6P C. C. Product Coil Assy. ( Pumps)

7 SA40980 Top Cover Assembly - Stainless Steel

SA40981 UK Fridge Deck Assembly

SA40982 Export Fridge Deck Assembly

8 CM73429 Compressor Danfoss FR11G

CM74198 Compressor Electrolux GP12TB

9 OP71729 Overload Relay Danfoss FR11G

PI41613 Relay & Capacitor Electrolux GP12TB

10 OP71548 Capacitor Danfoss FR11G

11 OP73484 Drier

12 CN71284 Condenser

13 OP73807 Fan Blade

14 SA40978 Fan Motor Assembly

15 MMCP39823 Fan Mounting Bracket

16 SA40979 Agitator Motor Assembly

17 MMCP39469 Agitator Mounting Plate

18 OP71924 Shaft washers

19 OP73625 Propellor

20 OP73825 Ice Bank Control - Mechanical

21 OP73935 Carbonator Control - UK

22 OP74614 Carbonator Control - Export

23 OP73823 Transformer

24 OP71668 Switch

25 OP74613 Key Switch Loom

26 MMCP39952 5P Post-Mix Valve Plate

27 MMCP39830 6P Post-Mix Valve Plate

28 83377-1 Dole Fast Flow Electric Valve

29 12-0040 Lancer Electric Valve

30 12-0060 Flomatic 424 Electric Valve

31 12-0060-01 Flomatic 424 Valve Block

32 OP74391 Valve Screws

33 OP74356 Carbonator

34 SA38683 Pressure Relief Valve

35 OP70128 Gas In Non-Return Valve

36 SA40987 Carbonator Pump Motor Assembly

37 PU70172-01 Carbonator Pump

38 OP73326 Double Non-Return Valve

39 SA40989 Carbonator Probe Assembly

40 MMCP39853 Drip Tray

41 MMCP39829 Drip Tray Support

42 MMCP39951 5P Cup Rest

43 MMCP39828 6P Cup Rest

44 OP73718 Filler Plug

45 OP71406/9 Lighting Tube

46 OP71411 Starter

47 SA40994 Electronic Ice Bank Probe

48 59187-217 Portion Control

49 59187-218 Portion Control with Soda Button

50 OP74112 Syrup Pump

SA40014 Lighting Pod - Pepsi-Cola

SA40013 Lighting Pod - Coca-Cola

SA40024 Lighting Pod - White Lens

XP3 Post-Mix Cold Carbonation Overcounter Dispenser Parts ListXP3 Post-Mix Cold Carbonation Overcounter Dispenser Parts List

XP3 Post-Mix Cold Carbonation Overcounter Dispenser Parts List

ITEM NO. W.D.E. PART No. DESCRIPTION

1 SA40987 Base Assembly - Blue

2 SA40976 Base Assembly - Stainless Steel

3 OP74466 Power Lead - 13 Amp Plug

4 OP74467 Power Lead - Euro Plug

5 SACACP-B01A 5P Cold Carb. Product Coil Assembly

6 MMCP39410B Top Cover Assembly - Blue

7 MMCP39410 TopCover Assembly - Stainless Steel

SA40975 UK Fridge Deck Assembly

SA40977 Export Fridge Deck Assembly

9 CM73429 Compressor - Danfoss FR11G

CM74198 Compressor - Electrolux GP12TB

10 OP71729 Overload Relay Danfoss FR11G

PI41613 Relay & Capacitor Electrolux GP12TB

11 OP71548 Capacitor Danfoss FR11G

12 OP73484 Drier

13 CN73820 Condenser

14 OP70970 Fan Blade

15 SA40978 Fan Motor Assembly

16 MMCP40143 Fan Mounting Bracket

17 SA40979 Agitator Motor Assembly

18 MMCP39469 Agitator Mounting Plate

19 OP71924 Shaft washers

20 OP73625 Propellor

21 OP72956 Ice Bank Control - Mechanical

22 OP73935 Carbonator Control - UK

23 OP74614 Carbonator Control - Export

24 OP73823 Transformer

25 OP71668 Switch

26 OP74613 Key Switch Loom

27 MMCP40138 5P Post-Mix Valve Plate

28 12-0040 Lancer Electric Valve

29 12-0060 Flomatic 424 Electric Valve

30 12-0060-01 Flomatic 424 Valve Block

31 OP74391 Valve Screws

32 OP74356 Carbonator

33 SA38683 Pressure Relief Valve

34 OP70128 Gas In Non-Return Valve

35 MMCP70142 Carbonator Pump Mounting Bracket

36 SA40988 Carbonator Pump Motor Assembly

37 PU70172-01 Carbonator Pump

38 OP73326 Double Non-Return Valve

39 SA40989 Carbonator Probe Assembly

40 SA40984 Plastic Foot Assembly

41 OP74471 Plastic Drip Tray

42 MMCP39418 Drip Tray Support

43 MMCP39447 5P Cup Rest

44 OP73718 Filler Plug

45 OP71404 Lighting Tube

46 OP71411 Starter

SA40016 Lighting Pod - Pepsi-Cola

SA40015 Lighting Pod - Coca-Cola

SA40025 Lighting Pod - White Lens

XP4 'McDonald's' Post-Mix Overcounter Dispenser Parts ListXP4 'McDonald's' Post-Mix Overcounter Dispenser Parts List

XP4 'McDonald's' Post-Mix Overcounter Dispenser Parts List

ITEM No. W.D.E. PART No. DESCRIPTION

1 SA40224 Base Assembly

2 OP74652 Mains Lead Assembly

3 OP774519 Gewiss Plug

4 SA40226 Coil Pack Assembly

5 SA40225 Top Cover Assembly

SA40227 Fridge Assembly

6 CM73429 Compressor - Danfoss FR11G

CM74198 Compressor - Electrolux GP12TB

7 OP71729 Overload Relay - Danfoss FR11G

PI41613 Overload Relay & Capacitor - Electrolux GP12TB

8 OP71548 Capacitor - Danfoss FR11G

9 OP73484 Drier

10 CN71284 Condenser

11 OP73807 Fan Blade

12 MO73806 Fan Motor

13 MMCP39823 Fan Mounting Bracket

14 MO74019 Agitator Motor

15 MMCP39469 Agitator Mounting Bracket

16 OP71924 Shaft Washer

17 OP73625 Propeller

18 OP73825 Ice Bank Control - Electronic

19 OP73823 Transformer

20 OP71757 Probe

21 MMCP39957 Probe Bracket

Miscellaneous

22 MMCP39988 Cap Holder Assembly

23 OP74053 Cap Holder Screw

24 OP74613 Key Switch Loom Assembly

25 MMCP39830 6P Valve Plate Assembly

26 OP74391 Valve Screws

27 MMCP39828 6P Cup Rest

28 MMCP39853 Metal Drip Tray

29 MMCP39822 Drip Tray Support

30 MMCP39987 Splash Plate

31 OP73718 Filler Plug

32 OP73129 Manometer Gauge

33 OP73082 Gauge Fitting

34 MC73205 Warning Lamp

36 83377-001 Dole Fast Flow Valve

37 48980-05 Stainless Steel Valve Internals (Set)

38 59187-217 Wilshire Portion Control (Board)

39 59187-218 Portion Control & Soda Button (Board)

ADVERTISING MODULE MOUNTED ON FRONTADVERTISING MODULE MOUNTED ON FRONT

ADVERTISING MODULE MOUNTED ON FRONT

ADVERTISING MODULE MOUNTED ON REARADVERTISING MODULE MOUNTED ON REAR

ADVERTISING MODULE MOUNTED ON REAR

Page is loading ...

MULTIPLEX XP3 / XP4 Operating instructions

Brand: MULTIPLEX

Model: XP3 / XP4

Type: Operating instructions

Cooling and recirculating syrups, carbonated water, and still water.
Maintaining the correct conditioning for serving draft soft drinks.
Carbonating water using an integral carbonator (Cold Carb versions) or a remote carbonator.
Dispensing carbonated soft drinks through dispense valves.
Setting the brix to the drink manufacturer's specification.

Download PDF

report

MULTIPLEX XP3 / XP4 Operating instructions

MULTIPLEX XP3 / XP4 Operating instructions

Related papers

Other documents