Then drill the external wall.
Position the drilling template. Drill at its
marked centre (page 7).
By means of a ø 42 mm drill bit make
a hole in the internal wall first.
Warning:
Position the antenna away from the edge
of the roof so it does not protrude from
the vehicle outline when the vehicle is
moving
ASSEMBLY INSTRUCTIONS
1
2
3
TELEPLUS 3G
DIRECTIONAL TV ANTENNA
wall
bracket
The Teleplus 3G antenna must be
assembled close to a vertical wall
where the wall bracket can be fitted.
Place the rubber seal on top of the flange.
5
7
SILICONE
6
4
Lock the union flange in place with the
screws.
Insert the washer and lock the tube sleeve
in place with the ring nut.
Insert the mast roof mounting bracket in
the dia. 42 mm hole bored in the roof,
making sure you apply a layer of silicone
under the ring nut.
A
B
C
8
9
10
11
Remove the
connector F and
insert the lead in
the pole.
Insert the pole in the antenna support
and introduce the rubber plug inside the
pole.
Pull down the pole until the face of plug
A is level with the clamp B. Make sure
the lead is positioned next to the wall C.
Tighten the pole with the 2 screws, keeping
it in the position illustrated in Fig. 10.
Introduce the nut in its seat on the back
of the wall bracket.
Fit the upper part of the wall bracket
without tightening all the way.
12
13
14
15
Screw on the antenna support, making
sure you do not pinch the coaxial cable.
Spread a thin film of Vaseline inside the
seal and introduce the pole.
Screw the coaxial lead onto the antenna
connector.
18
Fix the bracket unit to the wall.
Rotate the 2
VHF dipoles.
Position them in their seats and lock
them in place with the 4 knobs
19
20
17
16
25 cm Max
Insert the closure plug. Pass the lead
through the relevant hole and then screw
the connector F back in, making sure
none of the braid wire come into contact
with the central core.
CONNECTION TO THE AMPLIFIER
Connect the lead exiting from the pole to the ANT input of the amplifier. Connect, with the relevant lead,
the TV connector of the amplifier with the television. Connect the amplifier to a 230 V power socket or
a battery, making sure you do not invert the + and - terminals (Fig. 21).
OPERATING INSTRUCTIONS
1) Rotate the dB dial of the amplifier clockwise.
2) Tune the television to a channel available in the area where you are located.
3) Rotate and lift the antenna via the suitable pole until you get the best image on the TV.
USEFUL TIPS
Not all the television signals you can receive in the zone where you are located will necessarily originate
from the same direction. So if the quality of a programme image is poor try rotating the antenna as the
signal may be coming from a direction different from the others.
GAIN ADJUSTMENT
With the dB dial turned all the way clockwise amplifier sensitivity will be at maximum and it is therefore
able to receive the weakest signals. If, instead, the signals are very strong there may be image overlap
on the TV screen. In this case rotate the dB dial anticlockwise slowly until the image is perfect.
21
If the amplifier is connect to the battery,
this switch allows to cut-off the power.
Power supply 12/24 Vcc
Attention
Excess force when rotating
The dial past its ‘Stop’
Will cause it to Break
Recycling: with a view to reducing
disposal of waste electrical and
electronic equipment as much as
possible, do not throw out this end of
life appliance together with other
unsorted municipal waste, but make
use of a recycling centre.
22
42 mm
Mounting wall
Dampen and locate on the
mounting position
#
Cut-out drawing in 1:1 scale
When the vehicle is running, always set the
antenna in the position shown in the
drawing and tighten the wall outlet
06 - 11 - 19
/