ALC AHS627-23 Quick start guide

Brand: ALC

Model: AHS627-23

Type: Quick start guide

ALC AHS627-23 is a wireless security system that can be controlled from anywhere using the ALC Connect Plus app. It includes a camera, indoor siren, power switch, motion detector, 2 remote controls, and 2 door/window sensors. The camera can be set to record video and send notifications when motion is detected. The system can be armed and disarmed remotely, and you can create shortcuts to control multiple devices with a single tap. The system is easy to set up and use, and it can be expanded with additional devices.

Front cover

BACK cover

FO LD

Wireless Made Simple.

BASIC OPERATION

1 3

1 6

Setup Camera

75%9:41 AMCarrier

Camera Name

Enter a name

Location

Living room

Setup Security Code

Enter your new code

Repeat Security Code

Repeat your code

Connect AC Adapter to DC IN Jack and

the other end into a 120V/60Hz AC

outlet.

Control Hub

Connect the supplied Ethernet cable

from the router to the Ethernet jack on

the Control Hub.

Model: AHS627-23

For detailed installation and setup and to view the ALC 1 Year Limited

Warranty, please refer to the complete User’s Guide available on our

website: www.ALCWireless.com/support

SCAN

TO VIEW

COMPLETE

USER’S GUIDE

ALCWireless.com

Wireless

Made Simple.

NOTE: Do not place any device near water. STRANGULATION HAZARD: Infants have STRANGLED in power cords.

Keep power cords more than 3 feet away from cribs. When using your equipment, always follow basic safety precautions to reduce

the risk of ﬁre, electric shock and injury to persons. Illustrations are for reference only. Actual product speciﬁcations may vary.

For additional precautions and product information, please see owner’s manual at www.ALCWireless.com/support

QUICK START GUIDE

STAY/AWAY ARMING THE SYSTEM

When on the Status page, tap to Arm/Partially disarm the system.

Select one of the following options:

Stay: Only arms the Door/Window sensors so you can stay at home.

Away: Arms all devices.

ALC CONTROL APP

Control Hub with AC Cord and

Ethernet Cable x 1

Wireless Camera with AC

Cord and Bracket x1

Motion Detector With

batteries and Sticky Pad Set

Power Switch x2

Door/Window Sensor with

Battery and Sticky Pad Set x2

Remote Control x2

Quick Start Guide

IN THE BOX

Phillips head screwdriver or drill

may be required for installation

Installation

Indoor/Outdoor Camera

Quick

Simple

Set Up

Tools

Connect AC Adapter to DC IN Jack and the

other end into a 120V/60Hz AC outlet.

*Insert the Power Switch into a 120V/60Hz AC outlet.

For ﬁrst time use, it is recommended to turn ON each

device as you pair them. Turning the unit ON activates

the manual pairing mode.

Door/Window Sensor

A CR2032 battery has been

pre-installed in the Door/Window

Sensor for ﬁrst time use. Apply the

double-sided tape to the rear of both

sections of the Door/Window sensor.

Select a location on either a door or a

window. Make sure to attach the

smaller piece to the movable part of the

door/window frame.

Motion Detector

For ﬁrst time use, batteries are

pre-installed (3 AA batteries 3). Apply

the double-sided tape to the rear of the

Motion Detector as shown. Use the thick

tape for ﬂat wall mount or the thin table

for corner mounting. Select a location

between 2-2.5 meters (6-8 ft) from the

ﬂoor.

Download the Connect Plus App as follows:

APPLE IOS DEVICE:

From your iPhone or iPad, go to the

App Store and search for ALC Connect Plus.

ANDROID DEVICE:

From your Android smartphone or tablet

device, go to Google Play and search for

ALC Connect Plus.

When ﬁrst turning on the app

you will enter the Control Hub

(or System Name you gave)

Selection window. Simply tap

your Control Hub to enter.

The Status screen will then

appear.

Remove the plastic tabs on

the Door/Window sensors,

Remote control and PIR

Motion sensor. Tap on the

corresponding sensor on the

Status page to rename and

provide a location for the

sensor.

Power Switch: Tap on the

Power Switch icon to turn

On or Off and to change the

name and provide location

such as Hall Lamp.

PAIRING THE CONTROL HUB

PAIRING THE CAMERAPAIRING THE CAMERA

At the dashboard, tap “+” (Add Device).

Tap Camera from the Device list.

Plug camera into an electrical outlet and

the the camera will boot up taking up to

90 seconds. When the green Link

Status indicator begins blinking, the

camera is ready to be set up. Tap Next.

The app will search for your camera.

a. If you are using an iOS device, go

to step 6.

b. If you are using an Android

device, the search will locate the

camera and retrieve the DID

automatically. Tap it to continue

the setup.

Name the camera and the location of

the camera. Enter a new Security Code

(must be 6 characters or more, letters

and/or numbers). Repeat and then tap

Next.

Select your Wi-Fi network, enter the

network’s password and then tap

Next. The unit will prepare your

camera and then it will be paired.

For iOS devices follow the instructions

on the screen:

a. Tap on your iPhone Home

button.

b. Go to Settings, then Wi-Fi.

c. Select the Wi-Fi network called

“HD-xxxxxx”.

d. Enter the password 12345678,

then Join.

e. After it connects (checkmark will

appear next to the HD-xxxxxx),

go back and restart the ALC

Connect Plus app.

f. Continue with step 4.

IMPORTANT: All sensors are paired with the Control Hub at the factory. See below to pair again or to add devices.

Camera: Tap the Camera. At

this screen you can view the

camera. Also tap the icons

under the image to perform

the following:

Launch the previously

installed ALC Connect

App. At the next screen,

tap Add new system.

The app will search for

the Control Hub and

retrieve the Control Hub

DID automatically.

Name the system (i.e.

“Home System”) and

add a photo (if desired).

Tap Next.

Enter a Security Code

(must be 6 characters or

more, letters and/or

numbers). Repeat and

then tap Save.

DASHBOARD

Snapshot: Tap to capture screen

images. The snapshots will be

saved into the camera roll of your

mobile device.

Mute/Un-mute: Press to hear the

sound of the camera’s microphone

through the App. Tap again to

mute the sound.

Record: Tap to record. Video

records for about 1 minute.

For full camera information, see

the full Owners Manual at

www.alcwireless.com/support

or scan QR Code below.

Shortcut: Tap to create a shortcut.

A shortcut can be as simple as

"turn on all lights".

SETTINGS

You can set many advanced

features in the Settings menu.

• Set built-in Siren volume

and duration.

• Edit Arming scenarios.

• Turn Notifications and

Email alerts On/Off.

• Modify Security Code and

passwords.

See full explanation of Settings

in the Owners Manual at

www.alcwireless.com/support.

Note: A Micro SD Card is required to

to use the recording function on this

camera. Insert at the rear of the camera.

Home Security Anytime from Anywhere

Wireless Security

System

Please read these instructions completely

before operating this product.

Model: AHS627-23

NOTE: Avoid pointing a camera directly at any bushes or tree branches or objects that may naturally move due to winds.

1 2

Screw the Antenna clockwise

into the rear of the camera.

Secure the multi-position Camera Bracket to a stable

surface, ceiling or wall using the two screws. If

needed, two anchors are also included. Secure the

camera to the Camera Bracket using the three smaller

screws.

Connect the small end of the AC

adapter to the camera’s AC In jack.

Plug into electrical outlet when

ready to install App.

Recommendations for best system performance:

• iOS 7.0 or above.

• Android: Android

smartphone or tablet (version 4.3x or above).

• Storage: Class 10 MicroSD memory card (up to 128 GB).

• Bandwidth: 1Mbps or above upload/download speed suggested.

CAMERA INSTALLATION

CAMERA INSTALLATION + SETUP

Camera

Power Switch

Door Sensor

Motion Detector

Remote Control

Power Switch

OFF:

Add device:

ON:

Oﬄine:

Mag open:

Mag close:

Add Device

Indoor Siren

Camera

Power Switch

Motion Detector

Remote Control

Indoor Siren

1. System name

2. Tap to Arm/Disarm

3. Tap to set off panic alarm

4. Tap to record

5. Tap to go to device edit page

6. Tap to go to the Home screen

7. Tap to go to the Event page

8. Tap to go to the Setting’s page

9. Tap to add Camera and Scenario icons

to Menu at the bottom of screen.

Add System

75%9:41 AMCarrier

System Name

Enter a name

DID

CHXX-000666-XXXXX

Select a photo

Cancel

100%9:41 AMCarrier

Add device

75%9:41 AMCarrier

3 4

6 7

Secure the multi-position Camera Bracket to

a stable surface, ceiling or wall using the two

screws. Secure the camera to the Camera

Bracket using the three smaller screws.

Add shortcut:

Add Shortcut

Connect your iPhone to Camera

Setup Camera

100%9:41 AMCarrier

Cancel

1. Tap the Home button, and go to your iPhone

Settings > WiFi.

2. Select Wi-Fi name started with"HD-XXXXXX".

4. Back ALC Connect Plus app to proceed with

setup.

NOTE: Visit www.alcwireless.com/support to view

videos on how to setup the Hub, Sensors and

your Camera.

Add device

75%9:41 AMCarrier

Add new system

Add System

100%9:41 AMCarrier

Add System

100%9:41 AMCarrier

new s

ste

ALC AHS627-23 Quick start guide

ALC AHS627-23 Quick start guide

ALC AHS627-23 Quick start guide

Related papers

Other documents