Front cover
BACK cover
FO LD
FO LD
FO LD
Wireless Made Simple.
Connect AC Adapter to DC IN Jack and
the other end into a 120V/60Hz AC
outlet.
Control Hub
Connect the supplied Ethernet cable
from the router to the Ethernet jack on
the Control Hub.
Model: AHS616
For detailed installation and setup and to view the ALC 1 Year
Limited Warranty, please refer to the complete User’s Guide
available on our website: www.ALCWireless.com/support
SCAN
TO VIEW
COMPLETE
USER’S GUIDE
ALCWireless.com
Wireless
Made Simple.
NOTE: Do not place any device near water. STRANGULATION HAZARD: Infants have STRANGLED in power cords.
Keep power cords more than 3 feet away from cribs. When using your equipment, always follow basic safety precautions to reduce
the risk of fire, electric shock and injury to persons. Illustrations are for reference only. Actual product specifications may vary.
For additional precautions and product information, please see owner’s manual at www.ALCWireless.com/support
QUICK START GUIDE
Control Hub with AC Cord and
Ethernet Cable x 1
Motion Detector With
batteries and Sticky Pad Set
x1
Power Switch x1
Door/Window Sensor with
Battery and Sticky Pad Set x2
Siren With AC Cord, Bracket
and Screw Set x1
Remote Control x1
Quick Start Guide
IN THE BOX
Phillips head screwdriver or drill
may be required for installation
Installation
Quick
Simple
Set Up
Tools
Place unit back on bracket.
*Insert the Power Switch into a 120V/60Hz AC outlet.
For first time use, it is recommended to turn ON each
device as you pair them. Turning the unit ON activates
the manual pairing mode.
Door/Window Sensor
A CR2032 battery has been
pre-installed in the Door/Window
Sensor for first time use. Apply the
double-sided tape to the rear of both
sections of the Door/Window sensor.
Select a location on either a door or a
window. Make sure to attach the
smaller piece to the movable part of the
door/window frame.
Motion Detector
For first time use, batteries are
pre-installed (3 AA batteries 3). Apply
the double-sided tape to the rear of the
Motion Detector as shown. Use the thick
tape for flat wall mount or the thin table
for corner mounting. Select a location
between 2-2.5 meters (6-8 ft) from the
floor.
Siren
Remove back cover and insert the three
screws as shown. It is recommended to
install in a highly visible location with
minimum obstacles. Insert four AA
batteries (not included) into the back of
the Siren or connect the AC Adapter to
DC IN Jack and the other end into a
120V/60Hz AC outlet.
INSTALLATION OVERVIEW
IMPORTANT: All accessories are paired with the Control Hub at the factory. See below to pair again or to add devices.
Control Hub
Secure wireless central home
control/management center.
Motion Detector
Wireless portable/wall-mount
area motion alert sensor.
Door/Window Sensor
Wireless door/window access
alert sensor.
Indoor Siren
Wireless portable/wall-mount
alert siren.
Power Switch
Wireless appliance energy
management power switch/
signal repeater (single device)
Remote Control
Wireless multi-functional panic
remote controller.
Adapter DC 12V/1A
Batteries AA 1.5V x 3 Battery CR2032
Batteries AA 1.5V x 4
(not included)
or
Adapter DC
5V/1A
Battery CR2032
Home Security Anytime from Anywhere
Wireless Security
System
Please read these instructions completely
before operating this product.
Model: AHS616
ALC CONTROL APP
Download the Connect Plus App as follows:
APPLE IOS DEVICE:
From your iPhone or iPad, go to the
App Store and search for ALC Connect Plus.
ANDROID DEVICE:
From your Android smartphone or tablet
device, go to Google Play and search for
ALC Connect Plus.
DASHBOARD
Camera
Power Switch
Door Sensor
Motion Detector
Remote Control
Power Switch
OFF:
Add device:
ON:
Offline:
Mag open:
Mag close:
Add Device
Indoor Siren
Camera
Power Switch
Motion Detector
Remote Control
Indoor Siren
Indoor Siren
1. System name
2. Tap to Arm/Disarm
3. Tap to set off panic alarm
4. Tap to record
5. Tap to go to device edit page
6. Tap to go to the Home screen
7. Tap to go to the Event page
8. Tap to go to the Setting’s page
9. Tap to add Camera and Scenario icons
to Menu at the bottom of screen.
1
3 4
2
5
6
7
8
9
BASIC OPERATION
1
2
STAY/AWAY ARMING THE SYSTEM
When on the Status page, tap to Arm/Partially disarm the system.
Select one of the following options:
Stay: Only arms the Door/Window sensors so you can stay at home.
Away: Arms all devices.
When rst turning on the app
you will enter the Control Hub
(or System Name you gave)
Selection window. Simply tap
your Control Hub to enter.
3
Power Switch: Tap
on the Power Switch
icon to set the Auto Off
time. You can also
change the name and
provide location such
as Hall Lamp.
The Status screen will then
appear.
Remove the plastic tabs on
the Door/Window sensors,
Remote control, Siren and
PIR Motion sensor. Tap on
the corresponding sensor on
the Status page to rename
and provide a location for the
sensor.
SETTINGS
You can set many advanced
features in the Settings menu.
Default password is 123456.
• Set built-in Siren volume
and duration.
• Edit Arming scenarios.
• Turn Notifications and
Email alerts On/Off.
• Modify Security Code and
passwords.
See full explanation of Settings
in the Owners Manual at
www.alcwireless.com/support
or scan in the QR code at the
bottom right of this page.
PAIRING THE CONTROL HUB
2
3
1
Launch the previously
installed ALC Connect
Plus App. At the next
screen, tap Add new
system. The app will
search for the Control
Hub and retrieve the
Control Hub DID
automatically.
Name the system (i.e.
“Home System”) and
add a photo (if desired).
Tap Next.
Enter a Security Code
(must be 6 characters or
more, letters and/or
numbers). Repeat and
then tap Save.
Add System
75%9:41 AMCarrier
System Name
Enter a name
DID
CHXX-000666-XXXXX
Cancel
Next
Add new system
1
Add System
100%9:41 AMCarrier
Add System
100%9:41 AMCarrier
A
new s
ste
2
1
PAIRING ADDITIONAL DEVICES
The remaining devices are paired similar
ways. The siren and power switch will be
ready to pair upon plugging in. For the
other devices, remove the Plastic Tab to
enable the pairing.
4
Tap Pair, then remove plastic tab to start
pairing the Sensor. “Add Sensor
Completed” will appear and the Sensor
will be added.
Note: This image shows the Window/
Door Sensor.
At the Status screen, tap +.
3
Tap the desired device. Name the
sensor and the location, tap Next.
100%9:41 AMCarrier
Add device
75%9:41 AMCarrier
Add Door Sensor
75%9:41 AMCarrier
Pair
complete.
Cancel
TROUBLE PAIRING?
If the devices do not pair properly, then utilize the manual Pairing as follows:
Door/Window Sensor: If it did not detect the sensor, pair manually by
removing the battery for 5-10 seconds and then reinstall it (this will activate
the manual pairing).
Motion Detector: If it did not detect the sensor, pair manually by removing the
battery cover and then press the Pair button.
Remote Control: If it did not detect the Remote Control, press and hold the
Armed Stay button on the Remote Control until the blue LED blinks.
Siren: If it did not detect the Siren and press the Pair button located inside
the battery compartment.
NOTE: Visit www.alcwireless.com/support to view
videos on how to setup the Hub, Sensors and
your Camera.
1
Panasonic KXHNS105E Quick start guide
Essence WeR@Home Installation guide
QOLSYS QS9207-5208-124 Installation guide
Midco TCA203 User manual
Verizon Ring Alarm Security Kit With LTE User guide
Yale HSA6600 Owner's manual
SecurityMan iAlarmD2 Operating instructions