Page is loading ...
Page is loading ...
MCA1
50.0034.01.00 1/2
EXTERNAL AMPLIFIER ADAPTER MODULE
MCA1 MODULE
FUNCTION
MODULE INCLUDING THE CONTROLS OF THE SIGNALS TO ADAPT THE BGM, THE
MESSAGES AND THE ALARMS (INCLUDING THE PRIORITIES HIERARCHY)
STRUCTURE TO AN EXTERNAL AMPLIFIER.
DESCRIPTION
The system permits to select up to 5 music programs (4 BGM plus no-music) different and
to assign them to 12 zones.
The BGM is attenuated or completely attenuated when a message or alarm is being sent.
The amplifier incorporates a 50 Hz subsonic filter to avoid the possible saturation of the
speaker matching transformers when replaying very low frequencies. This filter is
selectable with a jumper.
FEATURES
INDICATORS:
PAGING
: Message being sent by the sound system
-40 / -20 / -10dB
: Output level indicator (from -40dB to -10dB)
INTERNAL
CONFIGURATIONS:
ZONES ASSIGNATIONS
BGM ASSIGNATION
: 1, 2, 3, 4, OFF
BGA
: On, Off
SUBSONIC
: On, Off
CONTROLS:
BGM VOL
: Adjust the BGM level
PAGE VOL
: Adjust the paging level (spoken messages or alarms)
BGA VOL
: Adjust the level of the sound messages configured as BGA
BGM ATT
: It permits to adjust the BGM attenuation level when it is required by the
chime/alarm
CONNECTIONS: OUT: Balanced output signal.
CONNECTING THE MCA1
To carry out the connection of this module you should follow the steps indicated in the figure on next page.
Define the musical program number (one of the existing in the installation) you wish to use as background music in the zone
with the jumpers marked with nr.1. Place a jumper in the desired musical program number. For example: If you want this
module to have BGM number 2, you should place one jumper in J115.
Define the zone associated to this amplifier. For example: If you want this amplifier to act in zone 3, insert a jumper in
J104 (marked with nr.2 on next page).
ATTENTION: Each MCA1 module can be assigned to just one zone.
Choose now the possibility to either hear or hear not the BGA messages in the selected zone by means of the jumper (ON
or OFF) marked with nr.3.
ATTENTION: Essential to place this jumper in ON or OFF. If it were not put this jumper, the module would not work
correctly.
MCA1
2/2 50.0034.01.00
Enable (ON) or disable (OFF) the subsonic filter at 50 Hz by means of the jumper marked with nr.4. We recommend to
enable the filter in all the cases except when using 12” or bigger speakers.
ATTENTION: Essential to place this jumper in ON or OFF. If it were not put this jumper, the module would not work
correctly.
Insert and screw the module and the chassis together in the front and back panels.
Connect the data buses (Flat 10- and 20-way cables) to the connectors marked with nr.5 in the figure on next page.
Link together the front and back panel. In this case you will have to connect following connector pair marked with nr.6:
J120-J101.
Once the complete installation of one or various chassis and the peripherals connections to ENVIRO has been carried out,
you should adjust the BGM, BGA and PAGE volumes controls and finally adjust the BGM attenuation as the final step in this
modules configuration.
MCA1 MODULE
1
2
4
3
5
6
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Ecler ENVIRO MCA1 Manuel utilisateur
- español: Ecler ENVIRO MCA1 Manual de usuario
- Deutsch: Ecler ENVIRO MCA1 Benutzerhandbuch
Related papers
Other documents
-
York PCE6 Technical Guide
-
York Sun Core XX Installation guide
-
-
-
-
Johnson Controls TempMaster ZD Series Installation guide
-
-
-
-
Johnson Controls ZJ Series Installation guide