WAGO 2-channel, 24VDC, 3.0ms User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Fronts eite 20 15 - mit Doc Var iabl en ( Sta ndar d) @ 9\ mod_1285229289866_0.docx @ 64941 @ @ 1

WAGO-I/O-SYSTEM 750

Manual

750-400(/xxx-xxx)

2DI 24V DC 3.0ms

"-Channel Digital Input Module 24 VDC, 2- to 4

-

Conductor Connection; High-side Switching

Version 1.3.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e zur Dokumentation/Impressum für Standardhandbücher - allg . Anga ben, Ans chri ften, Tel efo nnum mern und E- Mail -Adr esse n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with Underlying

Provisions ............................................................................................. 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 14

3.2 Connectors ............................................................................................... 15

3.2.1 Data Contacts/Internal Bus ................................................................. 15

3.2.2 Power Jumper Contacts/Field Supply ................................................ 16

3.2.3 CAGE CLAMP

®

Connectors ............................................................. 18

3.3 Display Elements .................................................................................... 19

3.4 Schematic Diagram ................................................................................. 20

3.5 Technical Data ........................................................................................ 21

3.5.1 Device Data ........................................................................................ 21

3.5.2 Supply ................................................................................................. 21

3.5.3 Communication .................................................................................. 21

3.5.4 Inputs .................................................................................................. 21

3.5.5 Connection Type ................................................................................ 22

3.5.6 Climatic Environmental Conditions ................................................... 22

3.6 Approvals ................................................................................................ 23

3.7 Standards and Guidelines ........................................................................ 25

4 Process Image ............................................................................................. 26

5 Mounting ..................................................................................................... 27

5.1 Mounting Sequence ................................................................................. 27

5.2 Inserting and Removing Devices ............................................................ 28

5.2.1 Inserting the I/O Module .................................................................... 28

5.2.2 Removing the I/O Module .................................................................. 29

6 Connect Devices ......................................................................................... 30

6.1 Connecting a Conductor to the CAGE CLAMP

®

................................... 30

6.2 Connection Examples .............................................................................. 31

6.2.1 2-Conductor Connection .................................................................... 31

6.2.2 3-Conductor Connection .................................................................... 31

6.2.3 4-Conductor Connection .................................................................... 32

7 Use in Hazardous Environments .............................................................. 33

4 Table of Contents WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

7.1 Marking Configuration Examples ........................................................... 34

7.1.1 Marking for Europe According to ATEX and IEC-Ex ...................... 34

7.1.2 Marking for America According to NEC 500 .................................... 39

7.2 Installation Regulations ........................................................................... 40

7.2.1 Special Conditions for Safe Use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 41

7.2.2 Special Conditions for Safe Use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 42

7.2.3 Special Conditions for Safe Use (IEC-Ex Certificate TUN 09.0001 X)43

7.2.4 Special Conditions for Safe Use (IEC-Ex Certificate IECEx TUN

12.0039 X) .......................................................................................... 44

7.2.5 Special Conditions for Safe Use According to ANSI/ISA 12.12.01 .. 45

List of Figures ...................................................................................................... 46

List of Tables ........................................................................................................ 47

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei se zur D o kume nt ation /Hi nw eise zu dies er D o kume ntati on - Ü ber schr if t 1 @ 4\ mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation is

included, if necessary.

Pos: 9 /A lle Ser ien (Al lg emei ne M od ul e)/Üb ers chr ift en für al le S eri en/H in weis e z ur D oku ment ati on/ Gül tig keit sber eic h - Ü ber schri ft 2 @ 12\ mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xx xx, S tan dar dvers ion un d au fg elist et e Var iant e n @ 1 4\mod_1358944038682_21.docx @ 109354 @ @ 1

This documentation is only applicable to the I/O module 750-400 (2DI 24V DC

3.0ms) and the variants listed in the table below.

Pos: 11 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Var iant e nlist en/ Var iant enli st e - 7 50-xxx - Stan dard versio n und Vari ante /025-000 (er w eitert er Te mper at urb ereic h) @ 9\mod_1281521920414_21.docx @ 63093 @ @ 1

Table 1: Variants

Item Number/Variant

Designation

750-400

2DI 24V DC 3.0ms

750-400/025-000

2DI 24V DC 3.0ms/T

Pos: 12 /A ll e Ser ien (Al lg emei ne M od ule)/ Hi nweis e zur D o kume ntati on /Hi nwei se/ Hin weis : G ülti g keit d er Anga ben für aufg el iste te V ari ant en @ 9\mod_1281520778141_21.docx @ 63085 @ @ 1

Documentation Validity for Variants

Unless otherwise indicated, the information given in this documentation applies to

listed variants.

Pos: 13 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/Hi nw eise /Ac htu ng: H in weis zur Do ku ment ati on B uskl emm en 750- xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 750-400 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 14.1 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/U rh eber sc hutz aus führ lic h @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 14.2 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 14 .3 /All e Seri en (All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei se z ur Dok um enta tio n/S ymbol e - Ü bers chr ift 2 @ 1 3\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 14 .4.1 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/ Gefa hr/Gef ahr: _Warnu ng vor P erson ensch äden all gemei n_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/G efa hr/G efa hr: _War nu ng vor Perso nensch äden dur ch ele ktris chen St rom_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 14 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/W arn ung/ War nung : _ War nu ng vor P erso nens ch äde n all ge mei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 14.4 .4 /All e Serien ( Allg emeine Modul e)/Wic htig e Erläut erung en/Si cherh eits- und sons tig e Hi nwei se/ Vor sic ht/ Vor sich t: _War nung v or P ers one nsc häde n all ge mein _ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 14 .4.5 /Al le Seri en (All gemei ne Mod ule) /Wi chti ge Erl äut eru nge n/Si cher heit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden durch elektrostatische Aufladung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 14 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Erläuterung @ 13\mod_1343310326906_21. doc x @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 14 .4.8 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/I nfor matio n/Inf orma tion: _ Weiter e Infor matio n allge mein_ - Erläu terung @ 13\mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 14.5 /Dokumentation allgemein/Gliederungselemente/---Seite nwec hsel --- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 14 .6 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Zahl ensy steme @ 3\ mod_1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 2: Number Notation

Number Code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 14.7 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur Do kument ation /Schr iftko nventi one n @ 3\mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 3: Font Conventions

Font Type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Program Files\WAGO Software

Menu

Menu items are marked in bold letters.

e.g.: Save

>

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 15 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 16 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für alle S erie n/Wich tige Er läut erungen /Wic htig e Erläuter ung en - Über schri ft 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 17.1 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Wi chti ge Erl äut eru nge n - Ei nleit ung @ 3\mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 17.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Wi chti ge Erl äuter u ngenR ec htlic he Gr undl ag en - Üb ersc hrift 2 @ 3\ mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 17.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungsvorbehalt - Übers chri ft 3 un d I nhalt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 17.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Pers onalq uali fikati onPer sonal qual ifika tion 750- xxxx - Ü bersc hri ft 3 und I nhalt @ 3\ mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be

carried out by electrical specialists with sufficient knowledge in automation. The

specialists must be familiar with the current norms and guidelines for the devices

and automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 17.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Üb erschr if t 3 und I nhal t @ 3 \mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the WAGO-I/O-SYSTEM 750 in Compliance with

Underlying Provisions

Fieldbus couplers, fieldbus controllers and I/O modules found in the modular

WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and

transmit them to actuators or higher-level control systems. Using programmable

controllers, the signals can also be (pre-) processed.

The devices have been developed for use in an environment that meets the IP20

protection class criteria. Protection against finger injury and solid impurities up to

12.5 mm diameter is assured; protection against water damage is not ensured.

Unless otherwise specified, operation of the devices in wet and dusty

environments is prohibited.

Operating the WAGO-I/O-SYSTEM 750 devices in home applications without

further measures is only permitted if they meet the emission limits (emissions of

interference) according to EN 61000-6-3. You will find the relevant information

in the section “Device Description” > “Standards and Guidelines” in the manual

for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 17.6 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/T echni sc her Zus tan d d er G erä te - Ü bersc hrift 3 un d Inhal t @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The devices to be supplied ex works are equipped with hardware and software

configurations, which meet the individual application requirements. WAGO

Kontakttechnik GmbH & Co. KG will be exempted from any liability in case of

changes in hardware or software as well as to non-compliant usage of devices.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 17.7 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 17.8 /All e Seri en ( All gemei ne Mod ule)/Ü bers chrift en für al le Seri en/Wi chtig e Erlä uteru ngenSi cher heitshi nweis e - Über schr ift 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 17.9 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äuter unge n/Sich erhei tshi nweis e/Einl eitu ng Sich erheits hin weise H ardw are @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 17 .10. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : N ich t an G erät en unter Sp ann ung arbei te n! @ 6\ mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on devices while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 17.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, Schränken oder elektrischen Betriebsräumen! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Install the device only in appropriate housings, cabinets or in electrical

operation rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 17.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : U nfal l verh ütung sv orsc hriften beachten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 17.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6 \mod_1260180753479_21.docx @ 467 39 @ @ 1

Pos: 17.1 1. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Defek te oder besch ädigt e Gerät e austaus chen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 17.1 1. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : G erät e vor kriec hen den und i sol ier e nden Sto ffen sch ütz en! @ 6\ mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 17.1 1. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Clean only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 17.1 1. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 17.1 1. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 17.1 1. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Elektr ostat isch e Entla dung v ermeid en! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge when touched. Please observe the safety precautions

against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the

devices, please ensure that environmental factors (personnel, work space and

packaging) are properly grounded.

Pos: 18 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 19 /Alle Ser ien ( All ge mein e Mo dul e)/Ü ber schr if ten f ür alle Ser ie n/Ger äte bes chr eib ung /Ger äte besc hr eibu ng - Über schri ft 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 20.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/A nwen dung /DI /An wen dung 75 0-x4xx DI @ 3 \mod_1233762736718_21.docx @ 27108 @ @ 1

The digital input module 750-400 (2DI 24V DC 3.0ms) receives control signals

from digital field (e.g. of sensors, transmitters, switches or proximity switches).

Pos: 20.2 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung/ DI/I /O-B esc hrei bu ng 7 50-04xx 2 DI 2-/3-/4-Leit er (DI, 24 V, 0 V und Erde) @ 5\ mod_1245910745265_21.docx @ 35994 @ @ 1

The I/O module has 2 input channels, providing a direct connection to 2-, 3- or 4-

wire sensors.

The sensors are connected to the following CAGE CLAMP

®

connectors: DI 1,

24 V, 0 V and ground, or DI 2, 24 V, 0 V and ground.

Pos: 20.3 /Serie 750 (WAGO-I/O-SYST EM)/ Ger äteb eschr ei bung/ Einl eitu ng/I /O-B esc hrei bu ng/ Allg emei n/V er weis auf Ka pitel "A nsc hlüss e" @ 8\mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the “Connectors” section.

Pos: 20.4 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B esc hrei bung /Al lg emei n/Ver wei s a uf K api tel "G erät e a nschli eß en" > " Ansc hlus sb eis piel (e)" @ 5\mod_1246015203281_21.docx @ 36298 @ @ 1

Connection examples are shown in section “Connecting Devices” > … >

“Connection Example(s)”.

Pos: 20.5 /Serie 750 (WAGO-I/O-SYST EM)/ Ger äteb esc hrei bung /Ei nlei tung /I/ O-Besc hrei bu ng/D I/I/ O-B esc hrei bung 75 0-x4xx DI RC-Fi lter 3, 0 ms @ 3\mod_1233755071062_21.docx @ 27080 @ @ 1

Each input channel has a RC noise rejection filter with a time constant of 3.0 ms.

Pos: 20.6 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B eschr ei bung/ DI/I /O-B esc hrei bu ng 7 50- x4xx D I H SS / pos iti vsch alt end ( 24 V) @ 3\ mod_1233831724648_21.docx @ 27231 @ @ 1

The I/O module inputs provide high-side switching. If the 24 V potential for field

power is switched to an input connection, the signal status for the corresponding

input channel is set to “high”.

Pos: 20.7 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzei ge/ LED Zus tan d Si gnal @ 3\mod_1233755258578_21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 20.8 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzeig e/Ver weis au f Kapit el "Anz eige elemen te" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 20.9 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/Ei nlei tung /Vers orgung /Vers orgu ng 24 V, 0 V, Er de über Leist ungs kontak te @ 10\mod_1298361740782_21.docx @ 69754 @ @ 1

The I/O module receives the 24 V voltage supply, the 0 V potential and the

ground potential for the field level from an upstream I/O module or from the

fieldbus coupler/controller via the power contacts used as blade contacts. It then

provides these potentials to subsequent I/O modules via the power contacts used

as spring contacts.

Pos: 20.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en /Sic her hei ts- und s ons tige Hi nwei se /Acht u ng/Ac ht ung: Ma xim aler Str om Leis tung s konta kte 10 A @ 3 \mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 20.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tung /V ersorgung/Galvanische Trennung Feld/System @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 20.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tung /V ersor gu ng/A nord nung unter Ber ücksi chtig ung der Leist ungs kontak te beli ebig @ 3\mod_1233756233468_21.docx @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 20.1 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Einlei tung/ Einsa tzber eich/ Einsa tzber eich 7 50-xxx x alle K oppler/C ontr oller ohne Ei nschrä nkung @ 3\mod_1232541691906_21.docx @ 26522 @ @ 1

The I/O module 750-400 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 21 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 22 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsic ht - Ü b erschr if t 2 @ 4\ mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 23 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsic ht/D ig italei nga ngs klem men /Ansic ht 750- 0400 @ 14\mod_1358169385512_21.docx @ 108550 @ @ 1

Figure 1: View

Pos: 24 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Ger ät ebesc hrei bu ng/A nsi cht /A nsic ht C ageC la mp® _Leg en de mit LED s @ 1 5\mod_1370867188922_21.docx @ 122225 @ @ 1

Table 4: Legend for Figure “View”

Pos.

Description

Details See Section

1

Marking possibility with Mini-

WSB

---

2

Status LEDs

“Device Description” > “Display Elements”

3

Data contacts

“Device Description” > “Connectors”

4

CAGE CLAMP

®

connectors

“Device Description” > “Connectors”

5

Power jumper contacts

“Device Description” > “Connectors”

6

Release tab

“Mounting” > “Inserting and Removing

Devices”

Pos: 25 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 26 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsc hlüs se - Über schr ift 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 27 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D ate nko ntakt e/Kl em menbu s - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 28 .1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nschl üss e/Da ten kon takt e - F eldbu sko ppler /-c ontr oll er, A bbi ldung u nd B esc hrei bu ng @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the fieldbus coupler/controller and the I/O modules as

well as the system supply of the I/O modules is carried out via the internal bus. It

is comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data Contacts

Pos: 28.2 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Acht ung /Ach tu ng: Buskl e mmen nic ht auf Gol dfe der konta kt e leg en! @ 7 \mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 28.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf g ute Erd ung der U mg ebu ng ac ht en! @ 7\ mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The devices are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the devices, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 29 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 30 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/Leistungskontakte/Feldversorgung - Übersc hrift 3 @ 6\ mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 31.1 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/ Vorsi cht /V orsi cht : Ver let zung sge fa hr dur c h sc harf kan tig e M ess erko nta kte! @ 6\ mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged blade contacts!

The blade contacts are sharp-edged. Handle the I/O module carefully to prevent

injury.

Pos: 31.2 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 3 LK (M ess er/ Leis tung s konta kte 3 L K (M ess er/ Fed er) - Ei nleitung @ 15\mod_1371723761988_21.docx @ 123734 @ @ 1

The I/O module 750-400 has 3 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as male contacts and the contacts on the right side as spring

contacts.

Pos: 31.3 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nschl üsse /Leist ung skont akte 3 LK (M esser /Feder ) - Abbildung @ 7\mod_1266318232808_21.docx @ 50691 @ @ 1

Figure 3: Power Jumper Contacts

Pos: 31.4 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 3 LK (M ess er/ Leis tung s konta kte 3 L K (M ess er/ Fed er) - Leg ende @ 15 \mod_1371723810708_21.docx @ 123742 @ @ 1

Table 5: Legend for Figure “Power Jumper Contacts”

Contact

Type

Function

1 Spring contact

Potential transmission (U

v

)

for field supply

2 Spring contact

Potential transmission (0 V)

for field supply

3 Spring contact

Potential transmission (ground)

for field supply

4 Blade contact

Potential feed-in (ground)

for field supply

5 Blade contact

Potential feed-in (0 V)

for field supply

6 Blade contact

Potential feed-in (U

v

)

for field supply

Pos: 31.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstig e Hinw eise/ Achtu ng/A chtung : Maxi maler Strom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Do not exceed maximum current via power jumper contacts!

The maximum current to flow through the power jumper contacts is 10 A.

Greater currents can damage the contacts.

When configuring your system, ensure that this current is not exceeded. If

exceeded, insert an additional supply module.

Pos: 32 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 33 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ans chl üss e/C AGE CL AMP- Ans chlüs se - Ü ber schr if t 3 @ 6\ mod_1256296337770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

®

Connectors

Pos: 34 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/A nschl üss e/Digi talei ngang sklem men/ Anschl üss e 750-04xx 2 DI 4-Leit er dir ekt (DIn, 24 V, 0 V, Er de) @ 14\ mod_1358169715256_21.doc x @ 1 085 54 @ @ 1

Figure 4: CAGE CLAMP

®

Connectors

Table 6: Legend for Figure “CAGE CLAMP

®

Connectors”

Channel

Designation

Connector

Function

1

DI 1

1

Input DI 1: Signal voltage

24 V

2

Input DI 1: Sensor supply

0 V

3

Input DI 1: Sensor supply

Ground

4

Input DI 1: Ground

2

DI 2

5

Input DI 2: Signal voltage

24 V

6

Input DI 2: Sensor supply

0 V

7

Input DI 2: Sensor supply

Ground

8

Input DI 2: Ground

Pos: 35 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seiten wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 19

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 36 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nzei geel e ment e - Ü bersc hrift 2 @ 4\ mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 37 /S eri e 7 50 ( WAG O-I/O-S YSTEM )/Ger äteb eschr eibu ng/Anz eige elem ente/D igital eing angs klemm en/Anz eigeel em ente 750- 04xx 2 DI (Agn, Cgn) @ 8\mod_1276591490399_21.docx @ 57738 @ @ 1

Figure 5: Display Elements

Table 7: Legend for Figure “Display Elements”

Channel

Designation

LED

State

Function

1 Status DI 1 A

Off

Input DI 1: Signal voltage (0)

Green

Input DI 1: Signal voltage (1)

2 Status DI 2 C

Off

Input DI 2: Signal voltage (0)

Green

Input DI 2: Signal voltage (1)

Pos: 38 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-400 2DI 24V DC 3.0ms

Manual

Version 1.3.0

Pos: 39 /Al le Seri en (Al lge mei ne Mo dul e)/Ü b ersc hrif ten f ür all e S erie n/G erä teb esc hreib ung /Sc he mati sch es Sc h altbil d - Ü bers chr ift 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1

3.4 Schematic Diagram

Pos: 40 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/S che mati sche Sc halt bil der/D igi tal ei nga ngs klem men /Sch emat is ches Sc hal tbild 75 0-0 400 @ 14\ mod_1358170098770_21.docx @ 108568 @ @ 1

Figure 6: Schematic diagram

Pos: 41 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Page is loading ...

WAGO 2-channel, 24VDC, 3.0ms User manual

Related papers

Other documents