WAGO 8-channel, 5-14VDC, 1A User manual

Brand: WAGO

Model: 8-channel, 5-14VDC, 1A

Type: User manual

Pos: 2 /Dokumentation allgemein/Einband/Einband Handbuch - Deckbl at t oh ne V aria nt enfel d (S ta ndar d) @ 9 \mod_1285229289866_0.docx @ 64941 @ @ 1

Manual

WAGO-I/O-SYSTEM 750

8 DO 5 ... 14 VDC, 1 A

750-534

Channel Digital Output Module 5 ... 14 V DC, 1 A,

high-side switching

Version 1.1.0

Pos: 3 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/I mpr ess um für Sta ndar dh and büch er - al lg. A ngabe n, Ansc hrifte n, Telef onn ummer n und E-Mai l-A dresse n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D-32423 Minden

Phone: +49 (0) 571/8 87 – 0

Fax: +49 (0) 571/8 87 – 1 69

E-Mail: [email protected]

Web: http://www.wago.com

Technical Support

Phone: +49 (0) 571/8 87 – 5 55

Fax: +49 (0) 571/8 87 – 85 55

E-Mail: [email protected]

Every conceivable measure has been taken to ensure the accuracy and

completeness of this documentation. However, as errors can never be fully

excluded, we always appreciate any information or suggestions for improving the

documentation.

E-Mail: [email protected]

We wish to point out that the software and hardware terms as well as the

trademarks of companies used and/or mentioned in the present manual are

generally protected by trademark or patent.

=== Ende der Lis te f ür T e xtmar ke Ei nb and _vor ne = ==

WAGO-I/O-SYSTEM 750 Table of Contents 3

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 5 /D ok ument ati on al lg em ein/V erz eic hni sse /Inh alts ver zei chni s - Ü bersc hrift oG und Ver zeich nis @ 3\mod_1219151230875_21.docx @ 21063 @ @ 1

Table of Contents

Table of Contents ................................................................................................... 3

1 Notes about this Documentation ................................................................. 5

1.1 Validity of this Documentation ................................................................. 5

1.2 Copyright ................................................................................................... 5

1.3 Symbols ..................................................................................................... 6

1.4 Number Notation ....................................................................................... 8

1.5 Font Conventions ...................................................................................... 8

2 Important Notes ........................................................................................... 9

2.1 Legal Bases ............................................................................................... 9

2.1.1 Subject to Changes ............................................................................... 9

2.1.2 Personnel Qualifications ....................................................................... 9

2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ...... 9

2.1.4 Technical Condition of Specified Devices ......................................... 10

2.2 Safety Advice (Precautions) .................................................................... 11

3 Device Description ..................................................................................... 13

3.1 View ........................................................................................................ 14

3.2 Connectors ............................................................................................... 15

3.2.1 Data Contacts/Internal Bus ................................................................. 15

3.2.2 Power Jumper Contacts/Field Supply ................................................ 16

3.2.3 CAGE CLAMP

Connectors ............................................................. 17

3.3 Display Elements .................................................................................... 18

3.4 Schematic Diagram ................................................................................. 19

3.5 Technical Data ........................................................................................ 20

3.5.1 Device data ......................................................................................... 20

3.5.2 Supply ................................................................................................. 20

3.5.3 Communication .................................................................................. 20

3.5.4 Inputs .................................................................................................. 20

3.5.5 Connection Type ................................................................................ 20

3.5.6 Climatic Environmental Conditions ................................................... 21

3.6 Approvals ................................................................................................ 22

3.7 Standards and Guidelines ........................................................................ 23

4 Process Image ............................................................................................. 24

5 Mounting ..................................................................................................... 25

5.1 Mounting Sequence ................................................................................. 25

5.2 Inserting and Removing Devices ............................................................ 26

5.2.1 Inserting I/O Module .......................................................................... 26

5.2.2 Removing the I/O Module .................................................................. 27

6 Connect Devices ......................................................................................... 28

6.1 Connecting a Conductor to the CAGE CLAMP

................................... 28

7 Use in Hazardous Environments .............................................................. 29

7.1 Marking Configuration Examples ........................................................... 30

7.1.1 Marking for Europe according to ATEX and IEC-Ex ........................ 30

7.1.2 Marking for America according to NEC 500 ..................................... 35

4 Table of Contents WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

7.2 Installation Regulations ........................................................................... 36

7.2.1 Special conditions for safe use (ATEX Certificate TÜV 07 ATEX

554086 X) ........................................................................................... 37

7.2.2 Special conditions for safe use (ATEX Certificate TÜV 12 ATEX

106032 X) ........................................................................................... 38

7.2.3 Special conditions for safe use (IEC-Ex Certificate TUN 09.0001 X)39

7.2.4 Special conditions for safe use (IEC-Ex Certificate IECEx TUN

12.0039 X) .......................................................................................... 40

7.2.5 ANSI/ISA 12.12.01 ............................................................................ 41

List of Figures ...................................................................................................... 42

List of Tables ........................................................................................................ 43

=== Ende der Lis te f ür T e xtmar ke V erz eic hnis _vor ne == =

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 7 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei s z ur D oku men ta tion/ Hin weis e z ur D o kume ntati on - Ü b ersc hri ft 1 @ 4 \mod_1237987661750_21.docx @ 29029 @ 1 @ 1

1 Notes about this Documentation

Pos: 8 /A lle Ser ien ( All ge mein e M odul e)/ Hin weis e z ur D oku men tati on/H i nweis e/Hi n weis : D okum ent atio n a ufbe wahr e n @ 4 \mod_1237987339812_21.docx @ 29026 @ @ 1

Keep this documentation!

The operating instructions are part of the product and shall be kept for the entire

lifetime of the device. They shall be transferred to each subsequent owner or user

of the device. Care must also be taken to ensure that any supplement to these

instructions are included, if applicable.

Pos: 9 /A lle Ser ien ( All ge mein e M odul e)/ Über sc hrif ten für all e Ser ie n/Hi nwei s z ur D oku men ta tion/ Gül tig kei tsber eic h - Üb ersc hrift 2 @ 12 \mod_1338912448776_21.docx @ 96469 @ 2 @ 1

1.1 Validity of this Documentation

Pos: 10 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Hi n weis e zur D okum ent ati on/G ülti gkei ts berei c h/Gül tig kei tsber ei ch D oku men tat ion Bus kle mme 75 0-xxxx, ohne Variantenangabe @ 14\mod_1358944037947_21.docx @ 109346 @ @ 1

This documentation is only applicable to the I/O module 750-534

(8 DO 5 ... 14 VDC, 1 A) of the WAGO-I/O-SYSTEM 750 series.

Pos: 11 /S erie 750 (WAGO-I/O-SYST EM )/H in weis e z ur D okum ent ati on/Hi n weis e/Ac ht ung : Hin wei s zur D oku ment ati on B us kle mme n 75 0-xxxx @ 4\mod_1237986979656_21.docx @ 29023 @ @ 1

The I/O module 750-534 shall only be installed and operated according to the

instructions in this manual and in the manual for the used fieldbus

coupler/controller.

Consider power layout of the WAGO-I/O-SYSTEM 750!

In addition to these operating instructions, you will also need the manual for the

used fieldbus coupler/controller, which can be downloaded at www.wago.com.

There, you can obtain important information including information on electrical

isolation, system power and supply specifications.

Pos: 12.1 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/U rh eber sc hutz aus führ lic h @ 4\mod_1235565145234_21.docx @ 27691 @ 2 @ 1

1.2 Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.

Non-observance will involve the right to assert damage claims.

Pos: 12.2 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 12.3 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Hi nwei s z ur D ok ume ntati on /Sym bol e - Ü bers chri ft 2 @ 13\mod_1351068042408_21.docx @ 105270 @ 2 @ 1

1.3 Symbols

Pos: 12 .4.1 /Al le Seri en ( All ge mei ne Mo dul e)/ Wic htig e Er lä uter ung en/ Sich erh eits- und sonstige Hinweise/Gefahr/Gefahr: _Warnung vor Personenschäden allgemein_ - Erl äuter ung @ 13\ mod_1343309450020_21.docx @ 101029 @ @ 1

Personal Injury!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.2 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonsti ge Hinw eise/ Gefa hr/Gef ahr: _ Warnu ng vor Per son enschä den durc h elek trisc hen Str om_ - Erläuterung @ 13\mod_1343309694914_21.docx @ 101030 @ @ 1

Personal Injury Caused by Electric Current!

Indicates a high-risk, imminently hazardous situation which, if not avoided, will

result in death or serious injury.

Pos: 12 .4.3 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/W arn ung/ War nung : _ War nu ng vor P erso nens ch äde n all ge mei n_ - Erläuterung @ 13\mod_1343309877041_21.docx @ 101035 @ @ 1

Personal Injury!

Indicates a moderate-risk, potentially hazardous situation which, if not avoided,

could result in death or serious injury.

Pos: 12 .4.4 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und so nsti ge H inw eis e/V orsic ht /Vor sic ht: _War nu ng vor P ers one nsc häde n al lg emei n_ - Erläuterung @ 13\mod_1343310028762_21.docx @ 101038 @ @ 1

Personal Injury!

Indicates a low-risk, potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

Pos: 12 .4.5 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden allgemein_ - Erläuterung @ 13\mod_1343310134623_21.docx @ 101041 @ @ 1

Damage to Property!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.6 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Achtung/Achtung: _Warnung vor Sachschäden durch elektrostatische Aufladung_ - Erläuterung @ 13\mod_1343310227702_21.docx @ 101044 @ @ 1

Damage to Property Caused by Electrostatic Discharge (ESD)!

Indicates a potentially hazardous situation which, if not avoided, may result in

damage to property.

Pos: 12 .4.7 /Al le Seri en (All gemei ne Mod ule)/ Wichti ge Erl äuter unge n/Sich erheit s- und sonstige Hinweise/Hinweis/Hinweis: _Wichtiger Hinweis allgemein_ - Eräuterung @ 13\mod_1343310326906_21.docx @ 101047 @ @ 1

Important Note!

Indicates a potential malfunction which, if not avoided, however, will not result in

damage to property.

Pos: 12 .4.8 /Al le Seri en (All gemei ne Mod ule) /Wi chti ge Erl äut eru nge n/Si cher heit s- u nd s ons tig e Hin wei se/I nf or matio n/I nfor ma tion: _ Weiter e I nf orma tio n al lge mei n_ - Er läu terung @ 13\mod_1343310439814_21.docx @ 101051 @ @ 1

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Additional Information:

Refers to additional information which is not an integral part of this

documentation (e.g., the Internet).

Pos: 12.5 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 12.6 /All e Seri en ( All ge meine Mo dul e)/H in weis e zur D oku ment ati on/Z ahle nsyst eme @ 3\mod_1221059454015_21.docx @ 21711 @ 2 @ 1

1.4 Number Notation

Table 1: Number notation

Number code

Example

Note

Decimal

100

Normal notation

Hexadecimal

0x64

C notation

Binary

'100'

'0110.0100'

In quotation marks, nibble separated with

dots (.)

Pos: 12 .7 /All e Seri en (Allg emeine Modul e)/Hi nweis e zur Do kument ation /Schr iftko nventi one n @ 3\mod_1221059521437_21.docx @ 21714 @ 2 @ 1

1.5 Font Conventions

Table 2: Font conventions

Font type

Indicates

italic

Names of paths and data files are marked in italic-type.

e.g.: C:\Programme\WAGO-I/O-CHECK

Menu items are marked in bold letters.

e.g.: Save

A greater-than sign between two names means the selection of a

menu item from a menu.

e.g.: File > New

Input

Designation of input or optional fields are marked in bold letters,

e.g.: Start of measurement range

“Value”

Input or selective values are marked in inverted commas.

e.g.: Enter the value “4 mA” under Start of measurement range.

[Button]

Pushbuttons in dialog boxes are marked with bold letters in square

brackets.

e.g.: [Input]

[Key]

Keys are marked with bold letters in square brackets.

e.g.: [F5]

Pos: 13 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 2 181 0 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 14 /Alle Ser ien (Al lge meine Mo dule)/ Über schrif ten für alle Ser ien/ Wichti ge Erlä uteru ngen/ Wich tige Er läuter ungen - Übersc hrift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1

2 Important Notes

Pos: 15.1 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Ei nl eit ung Wic htige Erl äut eru nge n @ 3 \mod_1221059818031_21.docx @ 21717 @ @ 1

This section includes an overall summary of the most important safety

requirements and notes that are mentioned in each individual section. To protect

your health and prevent damage to devices as well, it is imperative to read and

carefully follow the safety guidelines.

Pos: 15.2 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Wi chti ge Erl äuter u ngenR ec htlic he Gr undl agen - Üb erschr ift 2 @ 3\mod_1221060626343_21.docx @ 21726 @ 2 @ 1

2.1 Legal Bases

Pos: 15.3 /Alle Serien (Allgemeine Dokumente) (Allgemeine Module)/Wichtige Erläuterungen/Änderungsvorbehalt - Übers chri ft 3 un d I nhalt @ 3\mod_1221060036484_21.docx @ 21720 @ 3 @ 1

2.1.1 Subject to Changes

WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any

alterations or modifications that serve to increase the efficiency of technical

progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from

the granting of patents or from the legal protection of utility patents. Third-party

products are always mentioned without any reference to patent rights. Thus, the

existence of such rights cannot be excluded.

Pos: 15.4 /Serie 750 (WAGO-I/O-SYST EM)/ Wichtig e Erläut erung en/Per son alqual ifi kationP erson alqu alifi kation 75 0-xxxx - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1224061208046_21.docx @ 24063 @ 3 @ 1

2.1.2 Personnel Qualifications

All sequences implemented on Series 750 devices may only be carried out by

electrical specialists with sufficient knowledge in automation. The specialists

must be familiar with the current norms and guidelines for the devices and

automated environments.

All changes to the coupler or controller should always be carried out by qualified

personnel with sufficient skills in PLC programming.

Pos: 15.5 /Serie 750 (WAGO-I/O-SYSTEM)/Wichtige Erläuterungen/Bestimmungsgemäße VerwendungBestimmungsgemäße Verwendung 750-xxxx - Über schri ft 3 un d I nhal t @ 3\ mod_1224064151234_21.docx @ 24070 @ 3 @ 1

2.1.3 Use of the 750 Series in Compliance with Underlying

Provisions

Couplers, controllers and I/O modules found in the modular WAGO-I/O-

SYSTEM 750 receive digital and analog signals from sensors and transmit them

to the actuators or higher-level control systems. Using programmable controllers,

the signals can also be (pre-) processed.

The components have been developed for use in an environment that meets the

IP20 protection class criteria. Protection against finger injury and solid impurities

up to 12.5 mm diameter is assured; protection against water damage is not

ensured. Unless otherwise specified, operation of the components in wet and

dusty environments is prohibited.

Operating 750 Series components in home applications without further measures

is only permitted if they meet the emission limits (emissions of interference)

according to EN 61000-6-3. You will find the relevant information in the section

on "WAGO-I/O-SYSTEM 750"  "System Description"  "Technical Data" in

the manual for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-

SYSTEM 750 in hazardous environments. Please note that a prototype test

certificate must be obtained that confirms the correct installation of the system in

a housing or switch cabinet.

Pos: 15.6 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/T echni sc her Zus tan d d er G erä te - Ü bersc hrift 3 un d Inhal t @ 3\mod_1221060446109_21.docx @ 21723 @ 3 @ 1

2.1.4 Technical Condition of Specified Devices

The components to be supplied Ex Works, are equipped with hardware and

software configurations, which meet the individual application requirements.

WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in

case of changes in hardware or software as well as to non-compliant usage of

components.

Please send your request for modified and new hardware or software

configurations directly to WAGO Kontakttechnik GmbH & Co. KG.

Pos: 15.7 /Dokumentation allgemein/Gliederungselemente/---Seite nwechs el--- @ 3\ mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 15 .8 /All e Seri en (Allg emeine Modul e)/Ü berschr ifte n für alle S erie n/Wich tige Er läuter ung enSic herhei tshi nweis e - Übers chrif t 2 @ 6\mod_1260180299987_21.docx @ 46724 @ 2 @ 1

2.2 Safety Advice (Precautions)

Pos: 15.9 /All e Seri en ( All ge meine Do kum ente) ( All ge meine Mo dule) /Wi cht ige Erl äut eru nge n/Si cher hei ts hin weis e/Ei nl eitu ng Sich erh eits hin weis e H ard ware @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1

For installing and operating purposes of the relevant device to your system the

following safety precautions shall be observed:

Pos: 15.1 0. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : N ich t an G erät en unter Sp ann ung arbei te n! @ 6\ mod_1260180365327_21.docx @ 46727 @ @ 1

Do not work on components while energized!

All power sources to the device shall be switched off prior to performing any

installation, repair or maintenance work.

Pos: 15.1 0. 2 /S erie 750 ( W AGO -I/O-SY ST EM) /Wic htig e Er l äuter ung en /Sic her hei ts- un d s onsti ge H in wei se/G ef ahr/ Gefa hr: Ei nbau 07 50- xxxx nur in Geh äusen, S chrä nken oder ele ktrisc hen Betr iebsr äume n! @ 6\mod_1260180556692_21.docx @ 46731 @ @ 1

Installation only in appropriate housings, cabinets or in electrical operation

rooms!

The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,

install the system and its components exclusively in appropriate housings,

cabinets or in electrical operation rooms. Allow access to such equipment and

fixtures to authorized, qualified staff only by means of specific keys or tools.

Pos: 15.1 0. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : U nfal l verh ütung sv orsc hri ft en b each ten! @ 6\mod_1260180657000_21.docx @ 46735 @ @ 1

Pos: 15.1 0. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /G efahr /G efahr : A uf normg er echt e n Ansc hlu ss ac hten! @ 6 \mod_1260180753479_21.docx @ 46739 @ @ 1

Pos: 15.1 1. 1 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Defek te oder besch ädigt e Gerät e austaus chen! @ 6\mod_1260180857358_21.docx @ 46743 @ @ 1

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts), since the long-term functionality of device/module involved can no

longer be ensured.

Pos: 15.1 1. 2 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : G erät e vor kri echen den und is olier end en Stoff en schüt zen! @ 6\mod_1260181036216_21.docx @ 46747 @ @ 1

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for handling

devices/modules.

Pos: 15.1 1. 3 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : Rei nig ung nur mi t zul äss ig en M at erial ien! @ 6\mod_1260181203293_21.docx @ 46751 @ @ 1

Cleaning only with permitted materials!

Clean soiled contacts using oil-free compressed air or with ethyl alcohol and

leather cloths.

Pos: 15.1 1. 4 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : K ein K ont a ktspra y verw end en! @ 6\ mod_1260181290808_21.docx @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Pos: 15.1 1. 5 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : V erpol ung ver mei de n! @ 6\mod_1260184045744_21.docx @ 46767 @ @ 1

Do not reverse the polarity of connection lines!

Avoid reverse polarity of data and power supply lines, as this may damage the

devices involved.

Pos: 15.1 1. 6 /Al le S eri en ( Allg em ein e Do ku ment e) (Al lg em eine M o dul e)/ Wich tig e Erl äuter u ngen /Sic h erhei ts hinw eise /Ac htu ng/A cht ung : El ektr ost atis ch e Entl a dung v ermeid en! @ 6\mod_1260181364729_21.docx @ 46759 @ @ 1

Avoid electrostatic discharge!

The devices are equipped with electronic components that you may destroy by

electrostatic discharge when you touch. Pay attention while handling the devices

to good grounding of the environment (persons, job and packing).

Pos: 16 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 13

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 17 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä tebeschreibung/Gerätebeschreibung - Übersc hrift 1 @ 3\mod_1233756084656_21.docx @ 27096 @ 1 @ 1

3 Device Description

Pos: 18.1 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/Ei nlei tung /Anw endung /DO/A nwen dung 7 50-x5xx DO @ 3\mod_1233764594468_21.docx @ 27120 @ @ 1

The 750-534 Digital Output Module transmits binary control signals from the

automation device to the connected actuators (e.g., solenoid valves, contactors,

transmitters, relays or other electrical loads).

Pos: 18 .2 /Serie 750 (WAGO-I/O-S YSTEM )/ Ger äteb eschr ei bung/ Einl eit ung/ I/O-B esc hrei bung /DO /I/O -Besc hrei bung 75 0-05xx 8 DO 1-Lei ter (DO 1 . .. DO 8) @ 4\ mod_1235647050031_21.docx @ 27858 @ @ 1

The module has eight output channels. Eight 1-conductor actuators may be

directly connected to the module. The actuators can be connected using

connection DO 1 … DO 8.

Pos: 18.3 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/I/ O-B esc hrei bung /Al lg emei n/Ver wei s a uf K api tel "A nsc hlüss e" @ 8\ mod_1276775378035_21.docx @ 57956 @ @ 1

The assignment of the connections is described in the "Connections" section.

Pos: 18.4 /Dokumentation allgemein/Gliederungselemente/------Leerzeil e------ @ 3\mod_1224662755687_0.docx @ 24460 @ @ 1

Pos: 18.5 /Serie 750 (WAGO-I/O-SYST EM)/ Ger äteb eschr ei bung/ Einl eitu ng/I /O-B esc hrei bung /DO /I/O -Besc hrei bung 75 0-x5xx D O HS S / posi ti vschal te nd ( 5 ... 14 V) @ 17\mod_1381744109998_21.docx @ 134027 @ @ 1

The I/O module outputs provide high-side switching. If the signal status of an

output channel is at "high" the 5 … 14 V potential for field power will be

switched to the appropriate output connection.

Pos: 18.6 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzei ge/ LED Zus tan d Si gnal @ 3\mod_1233755258578_21.docx @ 27087 @ @ 1

A green LED indicates the switched status of each channel.

Pos: 18.7 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/Ei nlei tu ng/L ED-A nzeig e/Ver weis au f Kapit el "Anz eige elemen te" @ 5\mod_1246010525000_21.docx @ 36194 @ @ 1

The meaning of the LEDs is described in the “Display Elements” section.

Pos: 18.8 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/Ei nlei tung /Vers orgung /Vers orgu ng DC 5/ 14 V über L eistung skon takt e @ 17\mod_1380633161265_21.docx @ 133401 @ @ 1

The I/O module receives the 5 (14) VDC potential and the 0 V potential for the

field level from an upstream I/O module or from the fieldbus coupler/controller

via the power contacts used as blade contacts. It then provides this potential to

subsequent I/O modules via the power contacts used as spring contacts.

Pos: 18.9 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd sonsti ge Hin weis e/Acht ung/A chtu ng: Ma ximaler Strom L eistung skon takt e 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power contacts!

The maximum current to flow through the power contacts is 10 A.

Greater currents can damage the power contacts.

When configuring the system, ensure that this current is not exceeded. If

exceeded, an additional potential feed module must be used.

Pos: 18.1 0 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/ Wichti g e Erl äuter ung en /Sic her hei ts- und sonstige Hinweise/Hinweis/Hinweis: Potentialeinspeiseklemm e für Erd e einsetz en! @ 3\mod_1226499037468_21.docx @ 25023 @ @ 1

Use potential feed module for Ground (earth)!

The I/O module has no power contacts for PE intake and transfer. Use a potential

feed module when a PE feed is needed for the subsequent I/O modules.

Pos: 18.1 1 / Ser ie 7 50 ( WAG O-I/ O-SYST EM )/G erät ebe schr eib ung /Ei nlei tung /V ersor gu ng/G al vanis ch e Tr en nung Fel d/S yste m @ 3\mod_1233756478750_21.docx @ 27102 @ @ 1

The field voltage and the system voltage are electrically isolated from each other.

Pos: 18.1 2 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Einlei tung/ Versor gung /An ordnung unter Ber üc ksichti gung der Leis tungs konta kte beli ebig @ 3\mod_1233756233468_21.docx @ 27099 @ @ 1

With consideration of the power jumper contacts, the individual modules can be

arranged in any combination when configuring the fieldbus node. An arrangement

in groups within the group of potentials is not necessary.

Pos: 18.1 3 / Ser ie 7 50 ( WAG O-I/ O-SYST EM)/ Gerät ebesc hreib ung/ Einlei tung/ Einsa tzber eich/ Einsa tzber eich 7 50-xxx x alle K oppler/C ontr oller ohne Ei nschrä nkung @ 3\mod_1232541691906_21.docx @ 26522 @ @ 1

The I/O module 750-534 can be used with all fieldbus couplers/controllers of the

WAGO-I/O-SYSTEM 750.

Pos: 19 /Doku ment ation all gemei n/Gl ie derung sel em ente /---Seit enwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 20 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/A nsic ht - Ü b erschr if t 2 @ 4\ mod_1240984217343_21.docx @ 31958 @ 2 @ 1

3.1 View

Pos: 21 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ans ic ht/D ig itala usg ang skl emm en/ Ansic ht 75 0-053 4 @ 17\mod_1382085863473_21.docx @ 134476 @ @ 1

Figure 1: View

Pos: 22 /S eri e 7 50 ( WA GO-I/ O-SYST EM)/ Gerät ebesc hrei bung/A nsic ht/A nsicht C ageCl amp® _Leg ende mit LED @ 15\mod_1370867188922_21.docx @ 122225 @ @ 1

Table 1: Legend for the “View” figure

Pos.

Description

Details see section

Marking possibility with

Mini-WSB

---

Status-LEDs

“Device Description” > “Display Elements”

Data contacts

“Device Description” > ”Connectors”

CAGE CLAMP

supplies

“Device Description” > ”Connectors”

Power jumper contacts

“Device Description” > ”Connectors”

Release tab

“Mounting” > ”Inserting and Removing

Devices”

Pos: 23 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 24 /A ll e Ser ien (Al lg emei ne M odul e)/Üb erschr ifte n für alle S erie n/Gerä tebes chrei bung /Ansc hlüsse - Übersc hrif t 2 @ 4\mod_1240984262656_21.docx @ 31961 @ 2 @ 1

3.2 Connectors

Pos: 25 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bu ng/A nsc hlüss e/D ate nko ntakt e/Kl em menbu s - Ü bersc hrift 3 @ 6\mod_1256294684083_21.docx @ 43660 @ 3 @ 1

3.2.1 Data Contacts/Internal Bus

Pos: 26.1 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/A nsc hlüss e/D ate nkon takt e - F eldbu sko ppler /-c ontr oll er, A bbi ld ung und Besc hrei bu ng @ 3\mod_1231771259187_21.docx @ 26002 @ @ 1

Communication between the coupler/controller and the I/O modules as well as the

system supply of the I/O modules is carried out via the internal bus. It is

comprised of 6 data contacts, which are available as self-cleaning gold spring

contacts.

Figure 2: Data contacts

Pos: 26.2 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtu ng: Bus kle mm en nic ht auf G oldf eder kon takt e leg en! @ 7\ mod_1266318463636_21.docx @ 50695 @ @ 1

Do not place the I/O modules on the gold spring contacts!

Do not place the I/O modules on the gold spring contacts in order to avoid soiling

or scratching!

Pos: 26.3 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- und sonstige Hinweise/Achtung/Achtung: ESD - Auf gut e Er dung der U mgeb ung ac hte n! @ 7\mod_1266318538667_21.docx @ 50708 @ @ 1

Ensure that the environment is well grounded!

The modules are equipped with electronic components that may be destroyed by

electrostatic discharge. When handling the modules, ensure that the environment

(persons, workplace and packing) is well grounded. Avoid touching conductive

components, e.g. data contacts.

Pos: 27 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

16 Device Description WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 28 /S eri e 7 50 ( WAG O-I/O-S YST EM) /Ger ät ebesc hrei bung /Ans chl üss e/Lei st ungs kont akt e/Fel d versor gu ng - Üb ersc hrift 3 @ 6\ mod_1256294692864_21.docx @ 43664 @ 3 @ 1

3.2.2 Power Jumper Contacts/Field Supply

Pos: 29.1 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Si cher heit s- u nd so nsti g e Hin weis e/ Vorsi cht /V orsi cht : Ver let zung sg efa hr durc h sc harf kan tig e M ess erko nta kte! @ 6\ mod_1256193279401_21.docx @ 43414 @ @ 1

Risk of injury due to sharp-edged male contacts!

The male contacts are sharp-edged. Handle the module carefully to prevent injury.

Pos: 29.2 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nschl üsse /Leist ung skont akte 2 LK (M esser/Leistungskontakte 2 LK (Messer/Feder) - Einleit ung @ 15 \mod_1371721641099_21.docx @ 123714 @ @ 1

The I/O module 750-534 has 2 self-cleaning power jumper contacts that supply

and transmit power for the field side. The contacts on the left side of the I/O

module are designed as male contacts and the contacts on the right side as spring

contacts.

Pos: 29.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /Ans chl üs se/L eist u ngs kont akte 2 LK (M ess er/ Leis tung s konta kte 2 L K (M ess er/F ed er) - A bbildu ng (ei nfac he Breite) @ 15\mod_1367500700037_21.docx @ 118396 @ @ 1

Figure 3: Power jumper contacts

Pos: 29.4 /Serie 750 (WAGO-I/O-SYST EM)/ Ger ätebesc hrei bung/A nschl üsse /Leist ung skont akte 2 LK (M esser /Leis tungs konta kte 2 LK (Messer/Feder) - Leg ende @ 15 \mod_1371721352500_21.docx @ 123710 @ @ 1

Table 3: Legend for the “Power jumper contacts” figure

Contact

Type

Function

Spring contact

Potential transmission (U

) for field supply

Spring contact

Potential transmission (0 V) for field supply

Blade contact

Potential feed-in (0 V) for field supply

Blade contact

Potential feed-in (U

) for field supply

Pos: 29.5 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd so nsti g e Hin weis e/Ach tung /Acht ung: M aximal er Stro m Leist ungs kontak te 10 A @ 3\mod_1226499143500_21.docx @ 25029 @ @ 1

Do not exceed maximum current via power contacts!

The maximum current to flow through the power contacts is 10 A.

Greater currents can damage the power contacts.

When configuring the system, ensure that this current is not exceeded. If

exceeded, an additional potential feed module must be used.

Pos: 29.6 /Serie 750 (WAGO-I/O-SYST EM)/ Wic htige Erl äuter unge n/Sic herhei ts- u nd sonsti ge Hin weis e/Hinw eis/Hi nwei s: Pote ntial eins peise klemme f ür Erde ei nset zen! @ 3\mod_1226499037468_21.docx @ 25023 @ @ 1

Use potential feed module for Ground (earth)!

The I/O module has no power contacts for PE intake and transfer. Use a potential

feed module when a PE feed is needed for the subsequent I/O modules.

Pos: 30 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 31 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Ans chl üss e/C AGE CL AMP- Ans chlüs se - Ü b erschr if t 3 @ 6 \mod_1256296337770_21.docx @ 43674 @ 3 @ 1

3.2.3 CAGE CLAMP

Connectors

Pos: 32 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /Ger ät ebesc hrei bung /Ansc hlüss e/Dig ital ausgang skl emmen/ Ansc hlüss e 750- 05xx 8 DO 1- Leit er @ 11\mod_1322218240918_21.docx @ 83734 @ @ 1

Figure 4: CAGE CLAMP

Connectors

Table 4: Legend for the “CAGE CLAMP

Connectors” figure

Channel

Designation

Connector

Function

DO 1

Output DO 1: Signal voltage

DO 2

Output DO 2: Signal voltage

DO 3

Output DO 3: Signal voltage

DO 4

Output DO 4: Signal voltage

DO 5

Output DO 5: Signal voltage

DO 6

Output DO 6: Signal voltage

DO 7

Output DO 7: Signal voltage

DO 8

Output DO 8: Signal voltage

Pos: 33 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

18 Device Description WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 34 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für alle S erie n/Gerä tebes chrei bung /Anzei geel ement e - Übers chri ft 2 @ 4\mod_1240984390875_21.docx @ 31964 @ 2 @ 1

3.3 Display Elements

Pos: 35 /S eri e 7 50 ( WA GO-I/ O-SYSTEM)/Gerätebeschreibung/Anzeigeelemente/Digitalausgangsklemmen/Anzeigeelemente 750-05xx 8 DO @ 11\mod_1322218413230_21.docx @ 83738 @ @ 1

Figure 5: Display elements

Pos: 36 /Doku ment ation all gemei n/Gl ie derung sel em ente /---Seit enwe chs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

Table 5: Legend for the “Display elements“ figure

Channel

Designation

LED

State

Function

1 Status DO 1 A

off

Output DO 1: not controlled

green

Output DO 1: controlled

2 Status DO 2 E

off

Output DO 2: not controlled

green

Output DO 2: controlled

3 Status DO 3 B

off

Output DO 3: not controlled

green

Output DO 3: controlled

4 Status DO 4 F

off

Output DO 4: not controlled

green

Output DO 4: controlled

5 Status DO 5 C

off

Output DO 5: not controlled

green

Output DO 5: controlled

6 Status DO 6 G

off

Output DO 6: not controlled

green

Output DO 6: controlled

7 Status DO 7 D

off

Output DO 7: not controlled

green

Output DO 7: controlled

8 Status DO 8 H

off

Output DO 8: not controlled

green

Output DO 8: controlled

WAGO-I/O-SYSTEM 750 Device Description 19

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 37 /A ll e Ser ien (Al lg emei ne M od ule)/ Üb ers chrif te n für al le S eri en/G erä teb esc hrei bu ng/Sc he mati sch es S ch altbi ld - Über schr ift 2 @ 4\mod_1240984441312_21.docx @ 31967 @ 2 @ 1

3.4 Schematic Diagram

Pos: 38 /S eri e 7 50 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /Sc he mati sche Sc hal tbil der/D ig ital aus ga ngs klem me n/Sc he matis ches Sc hal tbil d 75 0-0534 @ 17\mod_1382088540349_21.docx @ 134535 @ @ 1

Figure 6: Schematic Diagram

Pos: 39 /Doku ment ation all gemei n/Gli eder ungsel eme nte/---Seit en wechs el--- @ 3\mod_1221108045078_0.docx @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750

750-534 8 DO 5 ... 14 VDC, 1 A

Manual

Version 1.1.0

Pos: 40 /Al le Seri en (Al lge mei ne Mo dul e)/Ü b ersc hrif ten f ür all e S erie n/G erä teb esc hreib ung /Te chni sc he D ate n - Ü bers chri ft 2 @ 3\mod_1232967587687_21.docx @ 26924 @ 2 @ 1

3.5 Technical Data

Pos: 41 /S eri e 7 53 ( WA GO-I/ O-SYST EM) /G erät eb esc hrei bung /T echni sc he D ate n/T ech nisc he D ate n 75 3-0 534 @ 17\ mod_1381758399785_21.docx @ 134071 @ 3333 @ 1

3.5.1 Device data

Table 6: Technical data device

Width

12 mm

Height (from upper edge of 35 DIN rail)

64 mm

Depth

100 mm

Weight

48 g

3.5.2 Supply

Table 2: Technical data supply

Current consumption (internal)

20 mA

Current consumption typ. (field side)

25 mA / module + load

Voltage via power jumper contacts

5 V … 14 V DC (-15 % … + 10 %)

Isolation (Peak value)

500 V (system/ field)

3.5.3 Communication

Table 3: Technical data communication

Internal bit width (Terminal bus)

8 bit out

3.5.4 Inputs

Table 4: Technical data inputs

No. of outputs

Output current

1 A, short-circuit-protected

Inductive load switch off energy

dissipation W (max.)

0.26 J; L max = 2 x W max / I

Type of load

resistive, inductive

Max. switching frequency

2 kHz

Pos: 42.1 /All e Seri en ( All ge meine Mo dul e)/Ü bers chr ift en f ür alle S erie n/Ger äte bes chr eib ung /Ans chl uss tech ni k - Üb ersc hrif t 3 @ 1 7\mod_1380123271324_21.docx @ 132788 @ 3 @ 1

3.5.5 Connection Type

Pos: 42.2 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/T ech nisc he D at en V erdr ahtu ngs eb ene C C - 0,08 bis 2,5mm2 @ 17\mod_1380121238809_21.docx @ 132780 @ @ 1

Table 7: Technical Data – Field Wiring

Wire connection

CAGE CLAMP

Cross section

0.08 mm² … 2.5 mm², AWG 28 … 14

Stripped lengths

8 mm … 9 mm / 0.33 in

Pos: 42.3 /Serie 750 (WAGO-I/O-SYST EM )/ Ger äteb esc hrei bung /T echni sc he D ate n/A nsc hluss tec hni k/T ec hnisc he D at en L eist ungs ko nt akte ( Me sser /Fe der) @ 17\ mod_1380123464149_21.docx @ 132791 @ @ 1

Table 8: Technical Data – Power Jumper Contacts

Power jumper contacts

blade/spring contact, self-cleaning

Voltage drop at I

max.

< 1 V/64 modules

Pos: 42.4 /Serie 750 (WAGO-I/O-SYST EM) /Ger äte besc hrei bu ng/T ech nisc he D ate n/A nsc hluss tec h nik/T ec hnisc he D at en Kl e mme nbus @ 1 7\mod_1380123495844_21.docx @ 132794 @ @ 1

Page is loading ...

WAGO 8-channel, 5-14VDC, 1A User manual

WAGO 8-channel, 5-14VDC, 1A User manual

WAGO 8-channel, 5-14VDC, 1A User manual

Related papers

Other documents