2. Industrial & lab equipment
  3. Electrical equipment & supplies
  4. Electrical supplies
  5. Electrical wallplates
  6. Mircom
  7. LT-6152 TX3 Nano

Mircom LT-6152 TX3 Nano Quick Start

  • Hello! I am an AI chatbot trained to assist you with the Mircom LT-6152 TX3 Nano Quick Start. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
LT-6152 rev 3.4 © Mircom 2018. Printed in Canada
Subject to change without prior notice
See http://www.mircom.com/tx3nano for the latest information
For more information, see LT-6637 and LT-1194 on the included USB ash and http://www.mircom.com/tx3nano
Mircom Tech Support: 1-888-MIRCOM5 (888-647-2665) techsupport@mircomgroup.com
TX3 NANO QUICK START
WARNING:
Use the TX3-NANO-BB backbox for outdoor installations.
Do not mount the TX3 Nano in direct sunlight.
Disconnect the power before wiring.
TX3 Nano dimensions:
219 mm x 147 mm x 47 mm
(8 19/32” x 5 3/4” x 1 27/32”)
Mounting plate dimensions:
200 mm x 140 mm (7 27/32" x 5 1/2")
1. Press and hold the Home button for 10
seconds. The TX3 Nano’s IP address and
MAC address appear on the display.
2. On a computer on the same local area
network as the TX3 Nano, open Google
Chrome and type the IP address of the
TX3 Nano, and then press enter.
Username: admin
Password: admin
Congure
6
Insert security screw
5
Apply silicone to
this groove.
Do not apply
silicone to any
other part of the
TX3 Nano.
Apply outdoor-rated
weatherproof silicone to
groove in mounting plate
1
Bottom
Back
Holes for
aligning
gang box
Note:
Always use
6 fasteners
as shown in
step 2.
Use 2 screws to align
gang box with
mounting plate
3
Attach TX3 Nano
to mounting plate
4
Attach the
mounting plate
to wall with at
least 6 fasteners
Attach mounting
plate to wall
2
Front
MOUNTING
WARNING
To ensure the security of occupants,
change the admin password from its
default setting. See LT-1194 on the
included USB ash for details.
AUX PWR 12-48 V: 15 W auxiliary power input
(20-18 AWG)
PHONE LINE: ADC or NSL phone line
OUTPUT 1: lock (18 AWG)
INPUT 2: general purpose (22 AWG)
INPUT 1: door contact (22 AWG)
RS485: For future use
USB 2.0 port:
for debugging only
Maximum length:
2.4 m (8 ft)
RJ45 connector for
LAN connection and
Power over Ethernet
PoE maximum length:
100 m (328 ft)
USB switch:
for debugging only
(leave to the right)
Screw for adjusting
camera tilt
Contact rating for output 1:
30 VDC/2 A or
125 VAC/0.5 A
Slot for mini SIM (2FF)
card (only models
with -C, for example
TX3-NANO-S4-CX)
Note: The TX3 Nano has a tamper
feature. If it is powered on and not
mounted on the mounting plate, a
tone sounds. The tone stops sounding
when it is mounted.
For more information, see LT-6637 and LT-1194 on the included USB ash and http://www.mircom.com/tx3nano
Front
/