Legrand Unity Professional Services

Unity Installation

Professional Services Guide

Web Setup

Page 2

Table of Contents

Installation & Wiring Requirements

Graphical User Interfaces……………………………………………………………………………………………Page 4

Selective Call Intercom……………………………………………………………………………………………....Page 5

Cameras……………………………………………………………………………………………………………….Page 6

lyriQ Multi Room Audio………………………………………………………………………………………………Page 7

Local Area Network…………………………………………………………………………………………………..Page 9

Installation & Setup

How to terminate Cat5e………………………………………………………………………………………………Page 10

Updating Firmware……………………………………………………………………………………………………Page 12

Reserving Unity IP addresses……………………………………………………………………………………….Page 13

Accessing Web Setup………………………………………………………………………………………………..Page 14

Configure Date/Time Settings……………………………………………………………………………………….Page 15

Changing Device Names…………………………………………………………………………………………….Page 17

Associating Cameras and Selective Call Intercom Devices……………………………………………………..Page19

Associating lyriQ Multi Room Audio Zones and Selective Call Intercom Devices…………………………….Page 20

IP Camera Configuration…………………………………………………………………………………………….Page 22

Port Forwarding Remote Mobile Control Applications……………………………………………………………Page 24

Operation & Setup

User Interfaces

How to change background colors……………………………………………………………………….Page 25

How to connect a mobile device………………………………………………………………………….Page 26

Intercom

How to Answer the Door…………………………………………………………………………………..Page 27

How to Make a Call………………………………………………………………………………………..Page 28

How to record and send messages………………………………………………………………………Page 29

How to play a message……………………………………………………………………………………Page 30

How to change a door chime……………………………………………………………………………..Page 31

How to record a custom door chime……………………………………………………………………..Page 32

How to disable mute and monitor modes………………………………………………………………..Page 35

How to setup door messaging…………………………………………………………………………….Page 37

Page 3

Table of Contents

Operation & Setup Continued

Music

How to operate music by room…………………………………………………………………………….Page 40

How to operate music by scene…………………………………………………………………………...Page 41

How to create music scenes……………………………………………………………………………….Page 42

How to operate music by source…………………………………………………………………………..Page 44

Player

How to select shared music………………………………………………………………………………..Page 45

How to catalog shared music………………………………………………………………………………Page 46

How to manually add a share………………………………………………………………………………Page 47

Windows 7 Settings..………………………………………………………………………………Page 49

Windows Vista Settings……………………………………………………………………………Page 54

Windows XP Settings…………………………………...…………………………………………Page 57

Apple OS X Settings…………………………………………………………………………….…Page 59

How to select internet radio stations………………………………………………………………………Page 61

How to setup a Tunein.com account……………………………………………………………………...Page 62

How to share music from the SD card (models & showroom only)…………………………………….Page 63

Cameras

How to monitor cameras from an LCD or TVDI…………………………………………………………..Page 65

How to monitor cameras over IP using a LAN connection….…………………………………………..Page 66

How to monitor cameras over IP using a WAN connection….………………………………………….Page 68

Weather

How to setup your location………………………………………………………………………………….Page 70

Events

How to create an event……………………………………………………………………………………..Page 71

Lighting

How to add RF Lighting Control……………………………………………………………………………Page 73

How to operate lighting zones & collections………………………………………………………………Page 76

How to operate lighting scenes…………………………………………………………………………….Page 77

How to create lighting scenes………………………………………………………………………………Page 78

Frequently Asked Questions and Trouble Shooting……………………………………………………………....Page 80

Internet Service Provider Connection……………………………………………………………………………….Page 85

Page 4

Installation & Wiring Requirements

1. GRAPHICAL USER INTERFACES

HA5000-xx LCD Console

 Box/Ring Requirement: 3-Gang (mud ring recommended)

 Cable Requirement: (1) CAT5e 328-foot max. (purple recommended)

 Termination Point: Structured Wiring Enclosure

 Connection Points: None

HA5009-xx LCD Console with lyriQ

 Box/Ring Requirement: 3-Gang (mud ring recommended)

 Cable Requirement: (2) CAT5e 328-foot max. (1 purple & 1 green recommended)

 Termination Point: Structured Wiring Enclosure

 Connection Points: L&R Speaker/L&R Line Level Phoenix Connectors

HA5010-xx LCD Console with High-Performance lyriQ

 Box/Ring Requirement: 3-Gang (mud ring recommended)

 Cable Requirement: (2) CAT5e 328-foot max. ( 1 purple & 1 green recommended) & (1) 16/4

 Termination Point: Structured Wiring Enclosure

 Connection Points: L&R Speaker Out, Sub Out, HA1000 Power Input Phoenix Connectors

HA5201-xx TV Display Interface (TVDI)

 Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

 Cable Requirement: (1) CAT5e 328-foot max. (purple recommended)

 Termination Point: Structured Wiring Enclosure

 Connection Points: Composite Video, L&R Analog Audio output to TV, 3.5mm IR target input

HA5000-xx/HA5201-xx Installation Diagram

HA5009-xx/HA5010-xx Installation Diagram

Page 5

Installation & Wiring Requirements

2. SELECTIVE CALL INTERCOM

IC5000-xx Selective Call Intercom Room Unit

• Box/Ring Requirement: 2-Gang (Legrand AC1009-02 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (White recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: None

IC5002-xx Selective Call Intercom Door Unit

• Box/Ring Requirement: 2-Gang (Legrand AC1009-02 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (White recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: Sensor Input/Door Chime Output (22/2 recommended)

IC5003-XX Selective Call Intercom Video Door Unit

• Box/Ring Requirement: 2-Gang (Legrand AC1009-02 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (White recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: Sensor Input/Door Chime Output (22/2 recommended)

IC5004-XX Selective Call Intercom Patio Unit

• Box/Ring Requirement: 2-Gang (Legrand AC1009-02 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (White recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: None

Selective Call Intercom Installation Diagram

Page 6

Installation & Wiring Requirements

3. CAMERAS

CM5002 Ball Camera

 Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

 Cable Requirement: (1) CAT5e 328-foot max. (yellow recommended)

 Termination Point: Structured Wiring Enclosure

 Connection Points: Microphone

CM1029 IR Camera

 Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

 Cable Requirement: (1) CAT5e 328-foot max. (yellow recommended)

 Termination Point: Structured Wiring Enclosure

 Connection Points: Microphone

F2299/2284 Bullet Camera

 Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

 Cable Requirement: (1) CAT5e 328-foot max. (yellow recommended)

 Termination Point: Structured Wiring Enclosure

 Connection Points: Microphone

F2286 Decorator Mount Mini Camera

 Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

 Cable Requirement: (1) CAT5e 328-foot max. (yellow recommended)

 Termination Point: Structured Wiring Enclosure

 Connection Points: None

CM5002 ONLY Installation Diagram

F Series/Third Party Camera Installation Diagram

Page 7

Installation & Wiring Requirements

4. LYRIQ MULTIROOM AUDIO

AU1004 Single Source Main Input

• Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (green recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: L&R Analog Audio Input, (3) IR Output, (1) IR Input

AU5015 Charge & Play Main Input

• Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (green recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: L&R Analog Audio Input, USB Charging Output

AU1015 airQast Main Input

• Box/Ring Requirement: N/A

• Cable Requirement: Custom Supplied

• Termination Point: Structured Wiring Enclosure

• Connection Points: Mini USB & 3.5mm phone jack for custom cable.

AU1011 Triple Source Main Input

• Box/Ring Requirement: 1-Gang (Legrand AC1009-02 mud ring recommended)

• Cable Requirement: (2) CAT5e 328-foot max. (green recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: (3) L&R Analog Audio Input, (3) IR Output, (1) IR Input

AU5008 Local Source Input (LSI)

• Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

• Cable Requirement: (2) CAT5e 328-foot max. (green recommended)

• Termination Point: Structured Wiring Enclosure/KVC (in series)

• Connection Points: L&R Analog Audio Input, RJ-45 CAT5e In/Out (backside)

AU5009 Standard Keypad Volume Control (KVC)

• Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (green recommended)

• Termination Point: Structured Wiring Enclosure

• Connection Points: L&R Speaker/L&R Line Level (backside)

Page 8

Installation & Wiring Requirements

AU5010 High Performance Keypad Volume Control (KVC)

• Box/Ring Requirement: 1-Gang (Legrand AC1009-11 mud ring recommended)

• Cable Requirement: (1) CAT5e 328-foot max. (green recommended) & (1) 16/4

• Termination Point: Structured Wiring Enclosure

• Connection Points: L&R Speaker Output/Sub Out/AU1000 Input (backside)

Interchangeable

main source inputs

16/4 Speaker wire

required with High

Performance zones.

Single Source Wiring Diagram

Multi Source Wiring Diagram

Page 9

Installation & Wiring Requirements

5. LOCAL AREA NETWORK (LAN)

DA1004 10/100 Router/Switch

 Cable Requirement: CAT5e 328-foot max. (blue recommended)

 Connection Points: (4) LAN / (1) WAN

DA1008 10/100/1000 Giga-bit Switch

 Cable Requirement: CAT5e 328-foot max. (blue recommended)

 Connection Points: (8) LAN

DA1101 Wireless Access Point

 Box/Ring Requirement: 3-Gang In-Ceiling / 1-Gang I-Wall

 Cable Requirement: (1) CAT5e 328-foot max. (blue recommended)

 Termination Point: Structured Wiring Enclosure (POE Module)

 Connection Points: (1) DATA IN / (1) DATA/

Basic Network Installation Diagram

Page 10

Handling Cat5e

Page 11

Handling Cat5e

Page 12

Updating Firmware

1. INTRODUCTION

Updating the firmware of Unity system requires a Local Area Network connection with a shared

internet connection. Always check for firmware updates prior to configuring a system for the first

time to make sure you are running the latest firmware version.

2. HOW TO STEP-BY-STEP

STEP 1: Using the left or right arrow button on the LCD or TVDI remote,

navigate the applications icon menu until the “Setup” icon is in the middle

of the display and press the “talk/select” button.

STEP 2: Use the down arrow button to select “System” and press

“talk/select” to enter the “Setup / System” menu

STEP 3: Press hot-key #2 on an LCD or the Green button on the

TVDI remote to “Update” the system firm ware version.

STEP 4: A pop up will appear. Press hot-key #3 on an LCD or the

YELLOW button on the TVDI remote to select “Yes” to start the update.

3. SPECIAL NOTES

 A pop up will appear followed by the

“UPDATING” screen to communicate the

status of the update. This can take up to 20

minutes to complete.

 Once the update is complete the system will

reboot itself.

Page 13

Reserved DHCP

1. INTRODUCTION

To ensure the Unity module always has the same IP address it is recommended that you set up

the local router’s reserved DHCP settings.

2. HOW TO STEP-BY-STEP

STEP 1: Open a web-browser on a PC or Mac connected to the network

and type in the IP address of the router. Legrand routers default

192.168.40.254

STEP 2: in the pop up, enter the username and password for

the router settings menu. Legrand routers default

admin/admin.

STEP 3: Open the LAN/DHCP Client List menu..

STEP 4: Click the checkbox under “Static” for the IP

addresses or MAC addresses of the Unity Module. All

Legrand devices have a MAC address starting with

00:26:EC:xx:xx.

STEP 5: Click “OK” to save the changes and restart the

router.

Page 14

Accessing Web Setup

1. INTRODUCTION

The most efficient way to configure and setup Unity is to use the web-setup utility served directly

from the Unity Module. Most settings can be adjusted in the web-setup.

2. HOW TO STEP-BY-STEP

STEP 1: Using the left or right arrow button on the LCD or TVDI remote,

navigate the applications icon menu until the “Setup” icon is in the middle

of the display and press the “talk/select” button.

STEP 2: Use the down arrow button to select the “Network Info” option and

press the “talk/select” button.

STEP 3: Open your PC web browser and enter

the Web Setup IP address into the address bar of

the browser.

3. SPECIAL NOTES

 The PC must be connected to the Local Area Network

supporting Unity.

 The only settings you cannot adjust from the web-setup

utility are display settings:

o LCD - Background Position Window Size,

Brightness, Color, Contrast and Background

Bubbles

o TVDI - Background, Position Window Size and

Background Bubbles

Page 15

Configuring Date/Time Settings

1. INTRODUCTION

There are two ways the date/time info can be setup. The easiest way is to make sure Unity is

connected to the local area network with a shared internet connection allowing the system to auto-

update from the web.

2. HOW TO STEP-BY-STEP

STEP 1: From the Unity Web Setup Menu, click on “System”.

STEP 2: Using the drop down menu next to “Enable Auto Clock Set” select

“No” if you want to manually set the time or if the Unity module is not

connected to the internet. The default setting is “Yes”.

STEP 3: Using the drop down menu next to “Select Time Zone”, select

the appropriate time zone for the installation. The default setting is EST.

STEP 4: Using the drop down menu next to “Daylight Savings Time” select

“NO” if the location does not observer DST. The default setting is “Yes”.

Page 16

Configuring Date/Time Settings

3. SPECIAL NOTES

 If you disabled the auto-clock set feature in Step 1, you can manually

set the “Time” and “Date” at the bottom of the screen. Use the drop

down to select AM, PM or a 24 hour clock.

 If you ever need to adjust DST start and end time you can make those

changes and press the “Set DST Default Values” button.

 Make sure you “Save Settings” after making all adjustments.

Page 17

Changing Device Names

 INTRODUCTION

Each device will be assigned a default name based on what type of device it is.

Changing a device name from the default is recommended to personalize the system to the

project and identify where the device is located such as in the Kitchen, Family Room, Bedroom 1

etc…

Further personalization is recommended once the home is occupied as Bedroom 1 might be

Johnny’s Room. It will be easier for the end user to operate the system properly if they are able to

select a device in Johnny’s Room.

Not only does naming devices make it easier for the end user to operate the system, it also makes

it easier for you to properly associate devices as described in pages 19-21 of this guide.

 HOW TO STEP-BY-STEP

STEP 1: From the Unity Web Setup Menu, click the device type you want to

rename. For example, click “Intercom”.

STEP 2: From the Main Setup: Device Setup menu click the

specific type of device you want to rename. For example click

“Room Settings”

STEP 3: From the list of devices “click to edit” the device

you want to rename. For example click “ROOM 1”

Page 18

Changing Device Names

STEP 4: Highlight the “Name” field and type in the new name. For example “Johnny’s Room”

 SPECIAL NOTES

 Name all devices before completing any additional set up options. To speed up setup

start with Music, followed by Cameras, then rename the Displays and Intercom devices.

 Music – lyriQ devices (KVCs and LCDs) will auto populate their default names as they

map to each zone input of the audio distribution module they are connected to. If the

Media Room keypad’s CAT5e is connected to the ZONES port # 1 of the audio

distribution module, change the name of “Zone 1” to “Media Room”.

 Cameras – To change the name of the cameras you will first need to open the Cameras

application and select each Camera 1-6 and identify the area each camera is displaying

or is installed in. If Camera #1 shows an image of the nursery, change the name of

Camera 1 to “Nursery”.

 Displays – Will auto populate depending on what type of display is connected.

i. LCDs will auto populate their name field as “Room #” because they function as

an intercom room station.

ii. TVDIs will auto populate as “Display xxxxxx”

 Intercom – Each Intercom Room Unit, including the LCDs will display their current

name at the top of the LCD display. Identify which Room # corresponds to which room

and name accordingly, orr use the locate function (the green target icon) located next to

each device to play an audible tone on that device. You will have to use the Locate

function for all Door and Patio Units as they do not display their name like room and

LCD stations.

Page 19

Associating Cameras & SCI devices

1. INTRODUCTION

Unity can display a camera image on the LCD when an intercom device is selected, allowing the

individual operating the LCD to see the selected room while making a call.

2. HOW TO STEP-BY-STEP

STEP 1: From the Unity Web Setup Menu, click “Intercom”

STEP 2: From the Main Setup: Intercom

Setup menu select the specific type of intercom unit you want

to associate a camera with. For example “Room Settings”

STEP 3: From the list of intercom units “click to edit” the

one you want to associate a camera with.

STEP 4: Using the “Camera Index” drop down menu,

select the camera you wish to associate with this

intercom unit.

STEP 5: Click “Save Settings”

3. SPECIAL NOTES

 Video door units are automatically associated with their camera. This step does not

need to be completed for those units.

Page 20

Associating lyriQ & SCI devices

1. INTRODUCTION

Unity can selectively mute up to four audio zones when an intercom device is active, allowing the

individual(s) in the room to hear the intercom call.

2. HOW TO STEP-BY-STEP

STEP 1: From the Unity Web Setup Menu, click “Intercom”

STEP 2: From the Main Setup: Intercom Setup menu select the

specific type of intercom unit you want to associate a lyriQ

keypad with. For example “LCD Console Settings”

STEP 3: From the list of LCD units “click to edit” the one you

want to associate a lyriQ keypad with.

STEP 4: Using the “Room/Zone A” drop down menu, select the

local lyriQ keypad or add-on you wish to associate with this

intercom unit.

STEP 5: Click “Save Settings”

Page is loading ...

Legrand Unity Professional Services - Web Setup User guide

Legrand Unity Professional Services - Web Setup User guide

Related papers

Other documents