ABB 83110-500 User manual

Brand: ABB

Model: 83110-500

Type: User manual

This manual is also suitable for

VER:1.2 │ │28.04.2017

ABB-Welcome

Pos: 2 /Di nA4 - Anl eitun gen Online /Inh alt /KNX /Doo rEntry /832 20-A P- xxx/Tit el blat t - 832 20-AP -xxx - ABB @ 1 9\mod_ 132 3249 806 476_15. docx @ 11 108 4 @ @ 1

83110-500

Audio integration

unit

83111-500

Extension unit

83501-101-500

Camera integration module

=== Ende der List e für Tex tma rke Cov er ===

ABB

-Welcome

| — 2 —

Pos: 4 /Bus c h-Jaege r (N eust rukt ur)/Mo dul-S truk tur/Onl i ne-D oku mentati on/ Inhal tsve rzeich nis ( --> Fü r alle Doku mente <--)/I nhal tsve rzeic hnis @ 19\ mod_13 206 490 44386_1 5.d ocx @ 109 653 @ @ 1

1 Safety ....................................................................................................... 3

2 Intended use ............................................................................................. 3

3 Environm ent .............................................................................................. 4

3.1 ABB devices ............................................................................. 4

4 Operation .................................................................................................. 5

4.1 Control elements ....................................................................... 5

4.2 Setting address ......................................................................... 7

4.2.1 physical address mode .............................................................. 7

4.2.2 Mapping address mode ............................................................. 8

4.2.3 To set function of 1st/2nd button ................................................ 9

5 Technical data......................................................................................... 11

5.1 Overview table ........................................................................ 11

6 Mounting/Installation ............................................................................... 12

6.1 Requirements for the electrician............................................... 12

6.2 General installation instructions ............................................... 13

=== E nde der Li ste für Tex tmarke TOC ===

ABB

-Welcome

Safety

| — 3 —

Pos: 6 /Bus ch-J aege r (N eust rukt ur)/Mo dul-S truk tur/Onl i ne-D oku mentati on/Ü be rschri ften (- -> Für alle D okum ent e <--)/ 1. Eb ene/S - T/Si cherhei t @ 18\ mod _13026 127 917 90_ 15.doc x @ 103 357 @ 1 @ 1

1 Safety

Pos: 7 /Busc h-Ja ege r (Neus truk tur)/ Mo dul-St ruktu r/Onli ne-D oku ment ation /Si cherhei t (-- > Für all e Dok umente <--)/W arn hinwei se /Sicher heit - 230 V @ 18\mod_ 130 260 681675 0_15 .docx @ 1033 08 @ @ 1

Warning

Electric voltage!

Dangerous currents flow through the body when coming into direct or

indirect contact with live components.

This can result in electric shock, burns or even death.

■ Disconnect the mains power supply prior to installation and/or

disassembly!

■ Permit work on the 110-240 V supply system to be performed only by

specialist staff!

Pos: 8 /Bus c h-Jaege r (N eust rukt ur)/Mo dul-S t ruktu r/Onli ne-D oku ment ation /Übe rschri ften (--> Für alle D okum ent e <--)/ 1. Eb ene/A - F/B estim mun gsge mäßer Gebrau ch @ 18\ mod_13 027 6332 1316_1 5.do cx @ 1034 83 @ 1 @ 1

2 Intended use

Pos: 9 /Di nA4 - Anl eitun gen Online /Inh alt/K NX /Doo rEntry /832 20-AP -x xx/B esti mmungs gem aess er Ge bra uch - 83 220 -AP-x xx- 500 @ 2 0\mo d_1 324561 168 699 _15. docx @ 11272 8 @ @ 1

The audio module assembly serves as voice and reception device for installing in a

suitable door and letter box system.

The 83110 …audio integration unit is an integral part of the ABB-Welcome door

communication system and operates exclusively with components from this system. The

device must only be installed in suitable housings such as flush-mounted letter boxes or

door systems.

The Extension Unit serves for connecting a maximum of 12 additional doorbell buttons

and an audio module assembly.

Camera module extends audio module assembly with video function.

The built-in keypad extension 83311 … is part of the ABB-Welcome door communication

system and operates exclusively with the components of this system. The device must

only be installed in suitable housings such as flush-mounted letter boxes or door

systems.

ABB

-Welcome

Environment

| — 4 —

Pos: 10 /B usc h-J aeger (Neus truk tur )/Modul -S trukt ur/O nline -Doku me ntatio n/Übe rsc hrif ten ( --> Fü r alle Doku men te <-- )/1. E bene /U - Z/U mw elt @ 18\ mod _13 026 1415896 7_1 5.d ocx @ 103383 @ 1 @ 1

3 Environment

Pos: 11 /B us ch-J aeger (Neus truk tur )/M odul -Strukt ur/O nli ne-D oku mentati on/ Umw elt ( --> F ür all e Doku me nte <-- )/Hinw eis e/Hinw eis - U mwel t - Hi nweis El ektr oge räte @ 1 8\mo d_1302 763 973 434 _15. docx @ 10350 0 @ @ 1

Consider the protection of the environment!

Used electric and electronic devices must not be disposed of with

domestic waste.

– The device contains valuable raw materials which can be recycled.

Therefore, dispose of the device at the appropriate collecting

facility.

Pos: 12 /D i nA4 - A nlei tu ngen Onlin e/U eb ersc hrift en/2 ./A BB Gera ete @ 19 \mo d_1 323 162 843832_ 15. doc x @ 11 087 5 @ 2 @ 1

3.1 ABB devices

Pos: 13 /B usc h-Jaeg er (Neus truk tur )/Modul -S trukt ur/O nline -Doku me ntatio n/Umw elt ( --> F ür all e Doku me nte <-- )/Hinwei s e/Hinw ei s - Umwel t - AB B E lektro gerät e @ 19\ mo d_13231 627 458 39_15. docx @ 110 867 @ @ 1

All packaging materials and devices from ABB bear the markings and test seals for

proper disposal. Always dispose of the packaging material and electric devices and their

components via the authorized collecting facilities and disposal companies.

ABB products meet the legal requirements, in particular the laws governing electronic

and electrical devices and the REACH ordinance.

(EU-Directive 2002/96/EG WEEE and 2002/95/EG RoHS)

(EU-REACH ordinance and law for the implementation of the ordinance (EG)

No.1907/2006)

ABB

-Welcome

Operation

| — 5 —

Pos: 18 /Di nA 4 - A nleitu ngen Onlin e/U ebersc hri ft en/1 ./Bedie nun g @ 18\mod_ 130 261 392 416 5_15.doc x @ 1 033 65 @ 1 @ 1

4 Operation

Pos: 19 /D i nA4 - A nlei tu ngen O nlin e/Ueb ersc hri ft en/2 ./Nor male r Bet rieb @ 18 \mo d_1 302 768 820965_ 15. doc x @ 10 3540 @ 2 @ 1

4.1 Control elements

Pos: 20 /Di nA 4 - A nleitu ngen Onli ne/ Ueb ersc hrift en/3 ./B edie nele men te @ 20\ mod_13 232 6022 055 9_1 5.do cx @ 1 116 47 @ 3 @ 1

Pos: 21 /Di nA 4 - A nleitu ngen O nlin e/In halt/K NX/ Do orEnt ry/83 220 -AP-xx x/Be dienel eme nte - 8322 0-AP -xxx @ 18\ mod_1 3032 128 53605_ 15.d ocx @ 103 673 @ @ 1

No. Functions

1 Terminals to connect the mechanical buttons

2 Connecting terminal for common dimensions

3 Relay out (fix as 3s)

4 Bus

5 Connection for camera module

6 Connection for extension unit

7 Microphone adjustment

8 Three rotary switches to set the address

9 Bell button tone on/off

10 Function of 1st/2nd pushbutton

11 Adjust the speaker volume

5 6

7 8 9

10 11

ABB

-Welcome

Operation

| — 6 —

No. Functions

1 Terminals to connect the mechanical buttons

2 Connecting terminal for common dimensions

3 Clamps for coupling several modules

4 Connections for audio integration unit and further extension unit.

Camera module extends audio module assembly with video function.

■ Video camera with automatic day/night switchover and infrared LEDs to illuminate

the night shots.

■ Installed heating to keep the lens free of condensation.

■ Vertical/horizontal detection angle: 86°/67°

■ Setting angle horizontal/vertical: +/-15°, mechanically adjustable

■ Consumer units: 4

■ Temperature range (Device): -25 °C - +55 °CC

Pos: 22 /B usch-J aeg er (N eust ruktur )/M odul -Strukt ur/O nline -Doku me ntatio n/St euer mod ule - Onli ne-Dok ume ntati on ( --> Für alle Dok ume nte <- -)/ +++++ +++++ ++ Sei ten umbruch ++++ ++++ +++ + @ 9\m od_126 8898 668 093_0. docx @ 52149 @ @ 1

ABB

-Welcome

Operation

| — 7 —

Pos: 26 /Di nA 4 - A nleitu ngen Onli ne/ Ueb ersc hrift en/2 ./B edie nakti onen @ 2 0\m od_ 1323 262294 281 _15. docx @ 11 191 1 @ 2 @ 1

4.2 Setting address

Pos: 71 /Di nA 4 - A nleitu ngen Onli ne/ Ueb ersc hrift en/3 ./A bschl uss wide rsta nd @ 19\ mod _13 2195807 990 6_1 5.do cx @ 1100 83 @ 3 @ 1

Pos: 72 /D i nA4 - A nlei tu ngen Onlin e/I nhal t/KN X/D o orEnt ry/B edie nun g/A bschl us swide rsta nd s et zen 83 220 -AP-x xx @ 19\ mod _13 1072 339 236 9_1 5.do cx @ 1 078 41 @ @ 1

4.2.1 physical address mode

1) The address of each button is generated automatically:

Button 1 is #01, button 2 is #02, etc.

2) The start address of button 1 can be shifted by use of the last 2 potentiometers.

For example, the last 2 rotary switches is 04, then button 1 = 04, button 2 = 05...

By default, the last 2 rotary switches is 01

ABB

-Welcome

Operation

| — 8 —

4.2.2 Mapping address mode

The address of each button can be set disorderly one by one, such as button 1=001,

button 2=003, button 3=005, button 4=002 …

If the last two rotary switches are set to 00, the device will work in the mapping

addressing mode, otherwise, it will work in the physical addressing mode.

start

1.Adjust rotary switches to 000

and hold any button for 3 s to enter into

programming mode (beep)

2. Adjust rotary switches to the required

value (like 003) and hold dedicated

button for at least 1~3s until hear the

prompt tone (beep)

continue to

program

End

3. Adjust rotary switches to X00

X=address of outdoor station and hold

any button for 3 s to exit programming

mode (double beep)

ABB

-Welcome

Operation

| — 9 —

4.2.3 To set function of 1st/2nd button

4.2.3.1 Function setting

1st button

0 1

hold 1st button for 3 s

0 0 9

hold 1st button for 3 s

ABB

-Welcome

Operation

| — 10 —

4.2.3.2 1st/2nd button setting in physical address mode

After set the 1st/2nd button, the address of the remain buttons are offset.

4.2.3.3 1st/2nd button setting in mapping address mode

After set the 1st/2nd button, the address of the remain buttons are fixed.

Pos: 75 /B usch-J aeg er (N eust ruktur )/M odul -Strukt ur/O nline -Doku me ntatio n/St euer mod ule - Onli ne-Dok ume ntati on ( --> Für alle Dok ume nte <- -)/ +++++ +++++ ++ Sei ten umbruch ++++ ++++ +++ + @ 9\m od_126 8898 668 093_0. docx @ 52149 @ @ 1

ABB

-Welcome

Technical data

| — 11 —

Pos: 76 /D i nA4 - A nlei tu ngen Onlin e/U eb ersc hrift en/1 ./T echni sc he D aten @ 18 \mo d_1 302 615 863 001 _15. docx @ 10 341 6 @ 1 @ 1

5 Technical data

Pos: 77 /D i nA4 - A nl eitu ngen Onlin e/In hal t/KN X/Do orE nt ry/83 220 -AP -xxx/ Tech nisc he D ate n - 832 20-A P-x xx @ 1 8\m od_ 130 321 285 4559 _15. docx @ 1 03705 @ @ 1

5.1 Overview table

Designation Value

Operating temperature -25 ℃ - +55 ℃

Storage temperature -40 ℃ - +70 ℃

Protection IP 44

Single-wire clamps 2 x 0.28 mm² - 2 x 0.75 mm²

Fine-wire clamps 2 x 0.28 mm² - 2 x 0.75 mm²

Bus voltage 20-30 V DC

Product dimensions 83110: 68 mm x 126 mm x 31 mm

83111: 68 mm x 50 mm x 24 mm

Pos: 78 /B usch-J aeg er (N eust ruktur )/M odul -Strukt ur/O nline -Doku me ntatio n/St euer mod ule - Onli ne-Dok ume ntati on ( --> Für alle Dok ume nte <- -)/ +++++ +++++ ++ Sei ten umbruch ++++ ++++ +++ + @ 9\m od_126 8898 668 093_0. docx @ 52149 @ @ 1

ABB

-Welcome

Mounting/Installation

| — 12 —

Pos: 79 /B us ch-J aeg er (Neus truk t ur)/M odul -St rukt ur/O nline -Doku me ntatio n/Ü bersc hri fte n (--> Für all e D oku mente < -- )/1. E bene /M - O/ Mont age / Ins tallat io n @ 18\ mod _13 0261 396611 1_1 5.do cx @ 1 033 73 @ 1 @ 1

6 Mounting/Installation

Pos: 80 /B usch-J aeg er (N eus trukt ur)/M odul -Strukt ur/O nli ne-Dok ume ntatio n/S iche rheit (--> Für alle D oku ment e <--) /War nhinweis e/S iche rheit - Nie ders pannun gs- und 230 V-Leit ung en @ 18\ mod _13026 178 214 91_15.d ocx @ 103 465 @ @ 1

Warning

Electric voltage!

Dangerous currents flow through the body when coming into direct or

indirect contact with live components.

This can result in electric shock, burns or even death.

■ Disconnect the mains power supply prior to installation and/or

disassembly!

■ Permit work on the 110-240 V supply system to be performed only

by specialist staff!

Pos: 81 /B us ch-J aeger (Neus truk tur )/M odul -Strukt ur/O nli ne -Doku ment atio n/Si che rheit (- -> Für alle D ok ument e < --)/W arnhi nweis e/S iche rheit - Fachk enntni sse @ 18\ mod_1 302 774 384 017_15. doc x @ 10 356 4 @ 2 @ 1

6.1 Requirements for the electrician

Warning

Electric voltage!

Install the device only if you have the necessary electrical engineering

knowledge and experience.

• Incorrect installation endangers your life and that of the user of the

electrical system.

• Incorrect installation can cause serious damage to property, e.g.

due to fire.

The minimum necessary expert knowledge and requirements for the

installation are as follows:

• Apply the "five safety rules" (DIN VDE 0105, EN 50110):

1. Disconnect from power;

2. Secure against being re-connected;

3. Ensure there is no voltage;

4. Connect to earth;

5. Cover or barricade adjacent live parts.

• Use suitable personal protective clothing.

• Use only suitable tools and measuring devices.

• Check the type supply network (TN system, IT system, TT system)

to secure the following power supply conditions (classic connection

ABB

-Welcome

Mounting/Installation

| — 13 —

to ground, protective earthing, necessary additional measures,

etc.).

Pos: 82 /D i nA4 - A nl eitu ngen Onlin e/In halt /KNX /Do orE nt ry/M onta ge/ Montage hi nweis e - Al lg emei n @ 1 9\m od_131 056 367 047 8_15 .docx @ 1 077 43 @ 2 @ 1

6.2 General installation instructions

• Terminate all branches of the wiring system via a connected bus device (e.g.,

indoor station, outdoor station, system device).

• Do not install the system controller directly next to the bell transformer and other

power supplies (to avoid interference).

• Do not install the wires of the system bus together with 100-240 V wires.

• Do not use common cables for the connecting wires of the door openers and wires

of the system bus.

• Avoid bridges between different cable types.

• Use only two wires for the system bus in a four-core or multi-core cable.

• When looping, never install the incoming and outgoing bus inside the same cable.

• Never install the internal and external bus inside the same cable.

• For optimum tone quality ensure that the module is seated correctly. Press the

microphone with the microphone adjuster directly against the voice plate.

Pos: 85. 1 /Di nA4 - Anlei tung en O nli ne/I nhal t/KN X/D oorE ntry/ 832 20-AP -xxx /Mo nta ge - Mo dule/ Mon tag e - Mon tage dos e -- 83 220 -AP -xxx @ 19\ mod _132325 040 684 8_1 5.doc x @ 1 110 98 @

Pos: 83 /B usch-J aeg er (N eust ruktur )/M odul -Strukt ur/O nline -Doku me ntatio n/St euer mod ule - Onli ne-Dok ume ntati on ( --> Für alle Dok ume nte <- -)/ +++++ +++++ ++ Sei ten umbruch ++++ ++++ +++ + @ 9\m od_126 8898 668 093_0. docx @ 52149 @ @ 1

ABB

-Welcome

Mounting/Installation

Pos: 95 /Di nA 4 - Anl eitu ngen Onl in e/In halt/K NX/D oorE nt ry/Proj ekti erung -M erkbl att/P roj ektie rPos: 9 7 /Busc h-J aege r (N eust ruktu r)/Mo dul-S tr uktu r/Onli ne-D oku ment ation /Rücks eit en (-- > Für alle Dok um ente <- -)/R ücks eit e - Bus ch-J aeger - All gemein @ 20\ mod _13273 200 748 86_15. docx @ 137 103 @ @ 1

Notice

=== Ende der List e für Tex tma rke Ba ckcove r ===