2. superbrightleds com
  3. PLLD2 Series

superbrightleds com PLLD2 Series User manual

  • Hello! I've reviewed the user manual for the superbrightleds PLLD2 series LED Parking Lot/Area Light. This document provides essential safety instructions, specifications including operating temperature and IP rating, and details the various mounting options available. It also covers lens replacement, and includes wiring diagrams. I'm ready to answer your questions about this product.
  • What are the recommended operating temperatures?
    What is the IP rating of this product?
    What should I do before starting installation?
    How do I remove the lens?
LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD2 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 12/06/2019
5yr
User Manual
Mounting Options Lens Removal and Installation
Safety and Notes
Environmental Specications
Operating Temperature -40°–122° F(-40°–50° C)
IP Rating IP65
Pole/Post Knuckle Mount (PLLD2-APM)Slip-Fitter Knuckle Mount (PLLD2-SF)
Fixed Pole/Post Mount (PLLD2-FPM)Trunnion Wall/Surface Mount (PLLD2-WM)
• Product should be installed and serviced by a certied electrician
in accordance with applicable national, state, and local building
and electrical codes.
• To reduce the risk of electric shock, ensure that the main power
source and circuit breakers are switched o before performing
any installation or wiring procedures.
• Avoid looking directly into lamp when illuminated.
• Ensure all mounts are securely attached and will support the
weight of the xture. Failure to properly support xture may
result in damage or injury, for which the manufacturer does not
assume responsibility.
Note: make certain to keep the light away from excess dust
and moisture during this process.
1. Remove screws around perimeter of lens.
2. Gently pry lens from light.
3. Install new lens and securely tighten all screws.
Specications
PLLD2-50K300-H3-HV (with PLLD2-SF)
Check product label for specific electrical
specifications related to installation.
Improper installation will void warranty.
LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD2 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 12/06/2019
5yr
User Manual
1. Remove the center bolt to separate the ange end from the
slip-tter end of the mount.
2. Run wiring through the ange that attaches to the light while
sliding the ange into the light.
3. Tighten the two bolts to secure ange to light.
4. Route wiring through slip-tter end, then reattach slip-tter end
to ange end.
5. With supply power o, connect wiring.
6. Slide mount over pole/post and tighten the four retaining bolts.
7. Once mount is secure, the center mount bolt that holds the
ange end and slip-tter end together can be loosened to
adjust the mounting angle of the light. Retighten center bolt
when the desired angle is achieved.
1. Detach light ange bracket from trunnion mount.
2. Run wiring through the ange that attaches to the light while sliding
the ange into the light.
3. Tighten the two bolts to secure ange to light.
4. Use trunnion mount to make mounting holes on wall/surface and
attach trunnion mount.
5. Route wiring through trunnion mount, then attach trunnion mount
to light ange bracket.
6. With supply power o, connect wiring.
7. Once installation is complete, the position locking bolts can be
removed and the center trunnion bolts can be loosened to adjust
the mounting angle of the light. Reinstall the position locking bolts
and retighten center bolt when the desired angle is achieved.
Trunnion Wall/Surface Mount (PLLD2-WM) Installation
Slip-Fitter Knuckle Mount (PLLD2-SF) Installation
LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD2 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 12/06/2019
5yr
User Manual
1. Open lower access plate on mount.
2. Run wiring through the ange that attaches to the light
while sliding the ange into the light.
3. Tighten the two bolts to secure ange to light.
4. Make appropriate mounting and wiring holes in pole/post
and attach mount to pole/post.
5. With supply power o, use the lower access plate to
connect wiring. Then close access plate.
1. Remove the center bolt to separate the ange end
from the pole/post mount end of the mount.
2. Run wiring through the ange that attaches to
the light while sliding the ange into the light.
3. Tighten the two bolts to secure ange to light.
4. Make appropriate mounting and wiring holes
in pole/post and attach mount end to pole/post.
5. Open lower access plate, route wiring through to
mount and attach ange end to mount.
6. With supply power o, use the lower access plate to
connect wiring. Then close access plate.
7. Once installed, the center mount bolt that holds the ange end and
the pole/post mount end together can be loosened to adjust the
mounting angle of the light. Retighten center bolt when the
desired angle is achieved.
Pole/Post Knuckle Mount (PLLD2-APM) Installation
Fixed Pole/Post Mount (PLLD2-FPM) Installation
LED Parking Lot/Area Light
Important: Read all instructions prior to installation. PLLD2 Series
4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com
Rev Date: V2.0 12/06/2019
5yr
User Manual
Dimensional Drawings (Accessories)
.70in
17.78mm
0.31in
8mm
5.49in
139.45mm
PLLD2-APM
0.31in
8mm
5.49in
139.45mm
PLLD2-FPM
.70in
17.78mm
PLLD2-SF
PLLD2-WM
2.61in
66.29mm
.81in
20.57mm
.42in
10.67mm
.82in
20.83mm
2.90in
73.66mm
3.70in
93.98mm
Wiring Diagram
Black
L L
N N
GND GND
White
Green
+ +
– –
Purple
Gray/Pink
Black
White
Green
Purple
Gray
100–277 VAC
Supply
1–10 V Dimmer
Note: External dimming is not applicable
to 277–480 VAC models.
/