GEONFINO A015 Keyless Entry Door Lock Smart Deadbolt Lock User manual

Brand
GEONFINO
Model
A015 Keyless Entry Door Lock Smart Deadbolt Lock
Type
User manual
Parts List
Measure to confirm that the backset is
either 2-3/8" or 2-3/4"(60 or 70mm).
Measure to confirm that the hole in the
door edge is 1"(25mm).
1.Prepare the door and check dimensions
1-1/2" to 2-1/8"
38 to54mm
1-2/5" to 2"
35mm to 50mm
Measure to confirm that the hole in the
door is 1-1/2"(38mm) to 2-1/8"(54mm).
Measure to confirm that the door is 1-
2/5" to 2"(35mm to 50mm) thick.
TOP
TOP
60mm
Spindle Hub is centered.
No adjustment is
required. Proceed
to next step.
TOP
Spindle Hub is not centered.
The door backset
maybe 70mm.
Rotate and pull the
latch as shown to
extend latch.
TOP
70mm
180°
2.Install the latch and strike
180°
TOP
TOP
TOP
(70mm)
Use a screwdirver to test if
deadbolt works smoothly. When
the screwdirver turns, the
deadbolt would be lock/unlock.
Install the latch
TOP
TOP
TOP
Install the latch
Install strike on the door frame
1"
25mm
IMPORTANT: Make sure the hole in door frame
is drilled a minimum of 1" (25mm) deep.
IMPORTANT: Before installation, make sure the latch is
fully retracted (in the unlocked position).
TOP
TOP
Please ensure the spindle is , and the Cable must be kept Horizontal
under the deadbolt during Installation.
3.Install the keypad
TOP
TOP
TOP
2-1/8"
(54mm)
If the hole is 2-1/8"(54mm)
A
If the hole is 1-1/2"(38mm)
B
TOP
1-1/2"
38 mm
Remove screw from adapter ring.
4.Install Mounting Plate
Put the mounting plate on
the waterproof rubber pad
The IC wired and tail bar go through
the hole of mounting plate
Look at the door from the OUTSIDE
Adjust the Toggle Switch ( in the bottom right
corner of the back panel ) and Turn Piece.
5.Confirm the direction of the door
Flip to L for Left-handle Flip to R for Right-handle
Horizontal for Left-handle Vertical for Right-handle
6.Install Interior Assembly
L
R
Connect the cable and ensure tight
cable connection. The tail bar should
be inserted into the turnpiece hole.
7.Install Battery Cover
A
B
C
D
E
F
G
H
J
K
K
L
I
TOP
What is inside
Strike/Strike Box
Waterproof Rubber Pad
A B C
D E F
G H J
I
K L
“TOP”is upward
TOP
TOP
TOP
Remove the adapter ring. Please ensure the spindle is , Horizontal
and the Cable must be kept under the
deadbolt during Installation.
Install the battery according to
the positive and negative poles
Download APP “TTLock”
TTLCOK APP add lock Android Mobile Phone--Please earch "TTLock" from Google Play.
Apple Mobile Phone--Please search "TTLock" from App Store.
Register a new account
Note: Please keep your phone near the door lock within meters.10
After adding the lock, the initial password: 123456 will
become invalid.
Note: Please keep your phone near the door lock
within 10 meters.
Light up the screen and add the lock
Click “ ” to unlock the door from outside or inside.
Note: Please keep your phone near the door lock within
32.8ft(10m).
Unlock with app
How to use
LOCK the door from outside
LOCK the door from inside
RFID Card needs to be added first
Fingerprint
(OPTIONAL)
Protect your User Codes and Master Code.
Protect your key. It is suggested to keep it outside the door,
such as your car.
Restrict access to your lock’s interior assembly and
routinely check your settings to ensure they have not
been altered without your knowledge.
This lockset is designed to provide the highest standard
of product quality and performance. Care should be taken
to ensure a long-lasting finish. When cleaning is required
use a soft, damp cloth. Using lacquer thinner, caustic
soaps, abrasive cleaners or polishes could damage the
coating and result in tarnishing.
Automatically locks the deadbolt after unlocking. This
feature is off by default. You can set the auto lock time in
the app.
IMPORTANT: Do not load batteries until the lock is completely
installed.
Required for programming and feature settings. The master
code can be used to unlock the door in vacation mode.
The default master code needs to be changed before
programming. Property owner/manager should keep this
information confidential.
1. Master Code (6 to 8) digits: The default Master Code is
123456. It is required that you change it to a code of your
own before programming.
2. User Code (6 to 8) digits: A total of 200 User Codes may
be programmed.
User can prevent PIN code exposure from strangers by
entering random digits before or after PIN code.
Auto Re-lock Mode
sendeKey Generate
Passcode eKeys Passcodes
RF
Cards WirelessKey
Fob
Authorized
Admin
Records
Settings
AutoLock
AutoLock
Thelockwilllockautomaticallyafterthetime.please
unlockitforonetimefirsttomakethesettingavailable.
AutoLock
AutoLock
CurrentSetting
AutoLock
AutoLock
A
u
t
oL
o
c
k
CurrentSetting
Cancel Time OK
5s
10s
15s
Auto Re-lock Mode can be set up in APP.(5s,10s,15s,30s,
60s,Custom) When the lock is unlocked via APP, passcode or
RFID card, it will re-lock automatically in the reset time.
External battery pack
  • Page 1 1
  • Page 2 2

GEONFINO A015 Keyless Entry Door Lock Smart Deadbolt Lock User manual

Brand
GEONFINO
Model
A015 Keyless Entry Door Lock Smart Deadbolt Lock
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents