Honeywell 8712309 Installation guide

Brand: Honeywell

Model: 8712309

Type: Installation guide

Page 1

Model DDBKP

Read this manual carefully before installing and operating!

ENGLISH

Installation & Operation Guide

Digital Deadbolt

Page 2

Index

INSTALLATION INSTRUCTIONS

Package Contents / Tools Required..........................................................

Prepare Door and Jamb.............................................................................

Adjusting Deadbolt Latch Set..................................................................

Installing Deadbolt Latch Set.....................................................................

Installing Exterior Assembly........................................................................

Installing Interior Assembly........................................................................

OPERATION INSTRUCTIONS

Digital Keypad Overview.............................................................................

Locking and Unlocking / Changing Programming Code /

Adding User Codes......................................................................................

Deleting User Codes / Automatic Lock Function /

Sound On and Off........................................................................................

Secure Lock-out Period / Restore Factory Settings /

Low Battery Warning / Consumer Friendly Message Guide....................

Installation Trouble Shooting...............................................................

Customer Service........................................................................................

Template.......................................................................................................

Programming Record..................................................................................

Limited Warranty.................................................................................

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6-8

Page 9

Page 10

Page 11

Page 12

Page 13

Page 14

Page 15-16

Page 17

Back

Cover

Page 1

INSTALLATION INSTRUCTIONS

Package Contents

Tools Required

Tools Required for Installation

on Pre-drilled Doors:

•PhillipsScrewdriver

Tools Required for Installation

on Doors That Require Drilling:

•Drill

•TapeMeasure

•Pencil

•2-1/8”(54mm)DrillHoleSaw

•1”(25mm)Drill

•1/16”(2mm)Drill

•Chisel

•Hammer

•PhillipsScrewdriver

DO NOT RETURN TO STORE! If any parts are missing or damaged,

pleasecallCustomerServicetollfreeat1-877-354-5457(M-F7am–5pmPST)

Deadbolt Strike Plate

DeadboltLatchSet(Adjustable)

2-3/8”(60mm)to2-3/4”(70mm)

5/16”(8mm)Screws-2ea. 1”(25mm)Screws-2ea.

3/4”(19mm)Screws-5ea. 1-3/8”(35mm)Screws-1ea.

InteriorAssembly

Mounting Plate

ExteriorAssembly

Entrykeys(2ea.)

Page 2

ADJUSTABLEDEADBOLTLATCHSET

NOTE: Deadbolt Latch Set is shipped with the backset set at 2-3/8” (60mm)

Measurethebackset(backsetisdistancebetweenedgeofthedoorandthe

centerofLock).

1. TO CONVERT FROM 2-3/8” (60mm) BACKSET TO 2-3/4” (70mm) BACKSET

 a.Holdlatchwithnumbersfacingforwardandthumbpressingonthebolt(Figure1a).

 b.Rotatethecylindercoverclockwise(Figure1b).

 c.Pullandtwisttheextensionplateallthewayout(Figure1c).

 d.Rotatethecylindercovercounterclockwisesothatthemarkingalignswith

  the2-3/4”(70mm)positionindicator(Figure1d).

2. TO CONVERT FROM 2-3/4” (70mm) BACKSET TO 2-3/8” (60mm) BACKSET

a.Holdlatchwithnumbersfacingforwardandthumbpressingonthebolt(Figure2a).

 b.Rotatethecylindercoverclockwise(Figure2b).

 c.Pushandtwisttheextensionplateallthewayin(Figure2c).

 d.Rotatethecylindercovercounterclockwisesothatthemarkingalignswith

  the2-3/8”(60mm)positionindicator(Figure2d).

Figure1a

Figure2a

Figure1b

Figure2b

Figure1c

Figure2c

Figure1d

Figure2d

Extension plate

Cylindricalcover

Yourlatchisnowset

2-3/8”(60mm)backset

Yourlatchisnowset

2-3/4”(70mm)backset

2-3/8”

(60mm)

2-3/8”

(60mm)

2-3/4”

(70mm)

2-3/4”

(70mm)

2-3/8”

(60mm)

NOTE: Do not extend Cylindrical Cover past 2-3/4” (70mm)

Page3

NOTE: For installation on doors with pre-drilled holes skip to page 4.

1. TEMPLATE

 a.Cutouttemplateprintedonpage15ofthisManual

 (Figure1a).

b. Foldtemplateandplaceondoor36”(925mm)from

  thegroundasmarked(Figure1b).

2. MARK THE DOOR FOR DRILLING

b. Mark center hole on door edge through guide on

 templatefor1”(25mm)latchbolt(Figure2a).

a. Mark center hole on door face through guide on

  templatefor2-3/8”(60mm)or2-3/4”(70mm)

  backset(Figure2b).

3. DRILL AND CHISEL DOOR

 a.Drill2-1/8”(54mm)holethroughdoorfaceasmarked

  forlockset(Figure3a).

 b.Drill1”(25mm)holeincenterofdooredgefor

  DeadboltLatchAssembly(Figure3b).

 c.InsertDeadboltLatchAssemblyinholekeepingit

  paralleltofaceofdoor.Markoutlineandremovelatch

  (Figure3c).

 d.Chisel1/8”(3mm)deeporuntillatchfaceisush

  withdooredge(Figure3d).

4. MARK AND DRILL DOOR JAMB

a. MarkcenterholeonedgeofjambevenwiththecenteroftheLatchBoltondoor

 edge.(Figure4a).

 b.Drill1”(25mm)hole1-3/16”(30mm)deepindoorjamboncentermark 

 (Figure4b).

 c.OutlineoutsideedgesofStrikePlate(Figure4c).

 d.Chisel1/8”(3mm)deepforStrikePlateoruntilush(Figure4d).

 e.InstallStrikePlateusingtwo3/4”(19mm).screwsprovided(Figure4e).

PREPAREDOORANDJAMB

Figure4a Figure4b

Figure4c Figure4e

Figure4d

NOTE: For Drive in Latch, drill hole size indicated on template and press

until it is ﬂush with door edge.

Figure1a

Figure2a Figure2b

Figure3a

Figure3c

Figure1b

Figure3b

Figure3d

Page4

1. INSTALLING THE DEADBOLT LATCH SET (need phillips head screwdriver)

 a.InsertDeadboltLatchSetintodooredgeholewiththeword

 “UP”andthearrowontheextensionplatefacingUP.Cross

 shapedspindleconnectorwillbeatthebottomoftheDeadbolt

 LatchSet(Figure1a).

 b.Makesurethefaceplatesitsushwiththedoor.Donotforce

 thelatchintothemortiseush.Chiseloutexcessmaterialif

  necessaryforausht.

 c.Usingtwo3/4”(19mm).screwsprovided,screwthelatchintothe

  doorwithahandheldscrewdriver.DONOTOVERTIGHTEN.

2. IDENTIFYING YOUR DOOR HANDING

Stand outside the door

 a.IfthehingesareontheleftyourdoorisLeftHanded(Figure2a).

 b.IfthehingesareontherightyourdoorisRightHanded(Figure2b).

NOTE: Deadbolt Latch must be retracted when installing

NOTE: You are standing outside the door

INSTALLINGDEADBOLTLATCHSET

OUT SWING DOOR IN SWING DOOR

Figure2a

Left Handed Door

Hinges are on the left side

Left Handed Door

Hinges are on the left side

Right Handed Door

Hinges are on the right side

Right Handed Door

Hinges are on the right side

Figure2b

Figure1a

Deadbolt Latch Extended

Deadbolt Latch Retracted

Page5

2. SECURING THE EXTERIOR ASSEMBLY TO THE DOOR

 a.Fromthesidemarked“Thissideagainst

  door”,routetheControlWirethroughthe

rectangular slot in the Mounting Plate

  (Figure2a).

 b.PlaceMountingPlateagainstdoorwithtailpiecepassing

  throughthecenterholeinthethreeholeset(Figure2b).

 c.SecuretheMountingPlatetotheExteriorAssemblyusing

  two1”(25mm)Screws(Figure2c).

 d.HandtightenwithaPhillipsScrewdriverleavinglooselyconnected(Figure2d).

e. Check that the Rubber Gasket is properly aligned and correct as necessary

 (Figure2e).

 f.Checkverticalalignmentofthelock(Figure2f).

 g.TightensecurelywithahandheldPhillipsScrewdriver.DO NOT OVER TIGHTEN

3. OPTIONAL INSTALLATION

 a.Usinga1/16”(2mm)drillbit,drillapilotholeinyourdoorusingthe

 MountingPlateupperholeasaguide(Figure3a).

b. Insert one 3/4”(19mm)screwandtighten.

1. INSTALLING THE EXTERIOR ASSEMBLY

 WorkwiththeDoorOpenforeasyaccess.

 a.UnpacktheExteriorAssembly.Usecaretonotscratchthegreencircuitboard

during handling and installation.

 b.CheckthattheRubberGasketisproperlyseatedontheExteriorAssembly 

 (Figure1a).

 c.InserttheExteriorAssemblyontothedoorwiththetailpiecegoingthroughthe

Deadbolt Latch Set cross shaped spindle connector in the VERTICAL POSITION.

 RoutetheControlWirethroughthedoorovertheDeadboltLatchSet(Figure1b).

NOTE: Deadbolt Latch must be retracted when installing

NOTE: Tailpiece must be

positioned vertically

NOTE: You are standing outside the door

INSTALLINGEXTERIORASSEMBLY

Right handed door view

Rubber

Gasket

Control

Wire

Tailpiece

(Vertical)

Latch

Hole

Mounting Plate

3/4”(19mm)screw

(OptionalInstallation)

1”(25mm)screws

Control Wire

Figure1a Figure1b

Figure3a

Figure2a-2f

NOTE: Lock and unlock using the key to see if

the Deadbolt Latch is opening and closing easily.

Page6

INSTALLINGINTERIORASSEMBLY

1. SET THE ENTRY SWITCH FOR LEFT OR RIGHT HANDED DOOR

 a.Gentlymovetheswitchto“L”forLeftHandedDoor(Figure1a).

 b.GentlymovetheSwitchto“R”forRightHandedDoor(Figure1b).

2. SET THE INTERIOR KNOB POSITION FOR LEFT OR RIGHT HAND HINGED DOORS

 a.TheInteriorKnobgoesintheVerticalpositionforRightHandedDoors(Figure2a).

 b.TheInteriorKnobgoesintheHorizontalpositionforLeftHandedDoors(Figure2b).

3. ATTACH THE CONTROL WIRE TO THE INTERIOR ASSEMBLY

 a.UsecaretoattachtheControlWiremaleplugtotheInteriorAssemblyfemale

socket connector.

 b.DonotforcetheControlWiremaleplugintotheInteriorAssemblyfemale

socket connector.

 c.TheControlWiremaleplughastwoalignmenttabsonthesmoothsideofthe

  plugwhichisthetopoftheplug.

 d.TheControlWiremaleplugisinsertedwiththesmoothsideupintotheInterior

 Assemblyfemalesocketconnector.

NOTE: Make sure

deadbolt Latch

is retracted

Left Handed Door

(Horizontal)

Entry Switch

(Left or Right)

Right Handed Door

(Vertical)

UnpacktheInteriorAssembly.Removethebatterycoverbyslidingthecoverupward.Locatethe

screwsholdingtheMountingPlatetotheInteriorAssembly.Removethescrewstoreleasethe

MountingPlatefromtheInteriorAssembly.

Figure1a-1b

Figure2a-2b

Page7

INSTALLINGINTERIORASSEMBLY(CONT.)

4. ATTACH THE INTERIOR ASSEMBLY TO DOOR

 a.PositiontheInteriorAssemblyoverthetailpieceandpushtheInteriorAssembly

 againstthedoor(Figure4a).

 b.Usingtwo5/16”(8mm)screws and one 1-3/8”(35mm)screw, attach

 theInteriorAssemblytotheMountingPlate.DO NOT OVER TIGHTEN SCREWS

(Figure4b).

5/16”(8mm)screws

1-3/8”(35mm)screw

NOTE: Lock and unlock using Interior Knob to see if the

latch is opening and closing easily.

INSTALLATION OVERVIEW

Strike Plate

BatteryCover

InteriorAssembly

Key

ExteriorAssembly

Rubber Gasket

Mounting Plate

Latch

5/16”(8mm)

screws

Optional

3/4”(19mm)

screw

3/4”(19mm)

screws

1-3/8”(35mm)

screws

1”(25mm)

Screw

Figure4a-4b

Page8

INSTALLINGINTERIORASSEMBLY(CONT.)

5. Installing Batteries

 a.Insert4AAhighqualityAlkalinebatteriesintotheBatteryCompartmentinthe

 directionnoted+/-ontheCompartment.TheLockwillbeep2times,thekeypad

 willilluminateblue,andtheHoneywellbuttonwillashgreentwicetosignifythat

 ithasreceivedpower(Figure5a).

 b.SlidetheBatteryCoverdownintothetrackontheInteriorAssemblytocover

thebatteries(Figure5b).

6. Testing Lock

With the Door Open

 a.TesttheLockusingtheinteriorKnob.Theboltshouldmovesmoothly.

 b.TestthelockusingtheKeypad.Tolockpressandthenpress“1234”

to unlock.

Override

AccessKey

ExteriorAssembly

InteriorAssembly

Interior

Knob

Battery

Cover

Light Indicator

Keypad

NOTE: Do not touch the keypad until the blue light turns off.

Do not use rechargeable batteries or non-alkaline batteries.

Figure5a-5b

Page9

OPERATION INSTRUCTIONS

ExteriorAssemblyOverview

Indicator light

Green

•IndicatesSuccessfulProgrammingStep

•IndicatesUnlockingisSuccessful

Red

•IndicatesFailedProgrammingStep

•IndicatesLockingisSuccessful

Electronic lock requires (4) High Quality

AA Alkaline batteries. When all 4 batteries

are installed in the correct position, hear 2

beeps and the keypad will illuminate blue.

DO NOT TOUCH the keypad until the keypad

stops illuminating.

Lock-Usedtolockdoor

Clear -Usedtoclearwrongkeypadentries

Unlock-Usedtounlockdoor

Programming -Usedinprogrammingsteps

5 Seconds -Completealltheprogrammingstepsintheprogrammingmodewithin5seconds.

Clear -Usethekeytoclearentriesincaseawrongbuttonispushed.

Lock button

Unlock button

FactorySettings

The lock comes factory preset with a:

Please change the Programming

Code and the User Code

as soon as possible after installation

to insure security.

Programming code - 123456

User code - 1234

User ID - 01

Batteries(notincluded)

Programming Symbols

Lock/Clear

Unlock/Programming

Programming Code

User Code (4-8 digits)

User ID (01-50, 2 digits)

Programming Tips

Page10

TO UNLOCK THE LOCK

UsingKeypad:EnteravalidUserCode(defaultcodeis1234)andpressandhear

1 beep and lights green.

TO LOCK THE LOCK

Using Keypad: Press and then hear 2 beeps and lights red.

CHANGECURRENTORPRESETPROGRAMINGCODE

FactorydefaultProgrammingCode=123456,thisisthemasterpasswordfor

yourlock.Allprogrammingfunctionsrequirethiscode.Followthebelowsequenceto

changetheProgrammingCodetoyourcustom6digitcombination.

TOADDANEWUSERCODE(youcanaddupto50newusercodes)

TheUserCodemustbea4-8digitcombination.EachUserCodeisthenlinked

toaUserID(whichisanynumberbetween01-50)toidentifyanindividualUser

Code.(UserID1-9shouldbeenteredas01-09sotheyare2digits).

Hear 1 beep and Light Indicator illuminates green

RecordNewandChangedCodesonProgrammingRecordlocatedonPage17

Hear 1 beep and Light Indicator illuminates green

NOTE:WhenaNEWUSERCODEisset,thedefaultfactorycode(1234)isdeleted

for safety.

RecordNewandChangedCodesonProgrammingRecordlocatedonPage17

123456   08 56785678

Forexample:toaddtheUserID-08toUserCode-5678,enterthefollowing:

4newRe-enter

1Re-enter

Locking and Unlocking

Changing Programming Code

AddingUserCodes

UC UC

PC PC

Page 11

DELETE ONE EXISTING OR PRESET USER CODE

TheunitcomeswithafactoryUserID=01forUserCode=1234.

IMPORTANT:Todelete1UserCode,thelockmusthavemorethan1UserCode

in its database.

SET OR CANCEL AUTO LOCK

You can set the lock to automatically close after each time the lock is opened. Time

valuerange=20-900seconds,enterthefollowing:

Youcan“mute”orturnthe“soundon”onyourlockbyenteringthefollowing.

(Factorysettingissoundon).

DELETE ALL USER CODES

IMPORTANT:thiswilldeletetheusercodesbutnottheprogrammingcode,enter

thefollowing

Hear 1 beep and Light Indicator illuminates green

SetAutoLock:

Hear 1 beep and Light Indicator illuminates green

SoundOff(1)-LightIndicatorilluminatesgreen

SoundOn(2)-Hear1beepandLightIndicatorilluminatesgreen

To cancel Auto Lock set the time to 00, enter the following:

CancelTimeValueAutoLock:

Hear 1 beep and Light Indicator illuminates green

2Existing re-enter

5TimeValue

61or2

500

3re-enter

Deleting User Codes

AutomaticLockFunction

Sound On and Off

PC PC

ID ID

1=SoundOff

2=SoundOn

Page 12

WarningsoundsandLEDashesredafter4incorrectcodeattempts:Keypadshuts

downfor30seconds.

To reset the lock to the original factory settings including the Programming Code

andallUserCodesremoveonebatteryfor10seconds.Reinsertthebatteryand

waitforalongandshortbeep.Press3timeswithin3seconds.Thelockwillbeep

andthelightindicatorwillturngreen.

BeepsandLEDashesredfor5seconds.Pleasereplacewithgoodquality

alkaline batteries.

Note:RomovingbatteriesdoesnoteraseactiveProgrammingorUserCodes.

NOTE:Whenbatteryisunderlowvoltage,thelockwillgivethe(LowBatteryWarning:BeepsandLEDashesredfor5seconds).During

thistimeyourlockcanstillwork.Howeveroncethevoltageislowerthan4.3V(calledSuper-LowVoltage),theoperationofthelockingand

unlockingwillnotwork,usermustreplacebatteriesimmediately.

Secure Lock out Period

RestoreFactorySettings

LowBatteryWarning

ConsumerFriendlyMessageGuide

Unlock/Validprogramming: 1 long beep and LED illuminates green

Lock: 2 short beeps and LED illuminates red

InvalidProgramming: 2shortbeepsandLEDashesredtwice

LowVoltage: Beepsfor5seconds

(7/9timesdependsonoperationisunlock/lock)

SuperLowVoltage: 4shortbeepsandLEDashesredfourtimes

4Incorrectcodeentryattempts: 2 short beeps and LED illuminates red each attempt

Poweron: 1 long beep and 1 short beep and LED illuminates green

Chip Reset: 1 long beep and 1 short beep and LED illuminates green

(mayoccurseveraltimesoronceinawhile)

Lock Error: 3longbeepsLEDashesredthreetimes

Repeat operation after Lock Error: 2 short beeps three times LED ashes red six times

Page13

INSTALLATIONTROUBLESHOOTING

Issue Solution

LatchWorkingBackwards-

Lockunlockswhenlock

button is pushed or locks

whenunlockbuttonorcodeis

pushed.

Directionswitchissettoincorrectsetting.

RemovetheInteriorAssemblyandmovethe

switchtotheoppositedirection.

•Checkthatyourswitchissetinthecorrect

position Left or Right Handed door.

If Correct

•RotateTurnknobandreinstallInterior

Assembly.RetestagainwhileholdingInterior

Assemblyinplace.

InteriorAssemblyknobwill

not turn.

Knoborverticaltailpieceisinstalledin

incorrectposition.RemoveInteriorAssem-

bly and reposition the Interior Knob. With the

DeadboltLatchretractedverifythatthetailpiece

isvertical.

Lockwillnotfunction

electronically.

•Checkthatallbatteriesarefreshhighquality

AlkalineBatteries.

•Checkforproperpolarity(+-)ofallbatteries.

•CheckthattheControlWireisattachedtothe

InteriorAssembly.

Lockgiveserrorsignalwhen

opening or locking and Dead-

boltLatchwillnotextendor

retractcompletelywhendoor

is closed.

Unlock door using key or interior knob. While

door is open, check that the Deadbolt Latch

operates smoothly. Check for proper alignment

ofthestrikeplate,adjustasneededtoassure

there is no binding against the Deadbolt Latch.

Deadbolt Latch is sticking. Installationscrewsofthelockmaybetootight

andhavetobeloosened.

•RemoveInteriorAssembly.

•SlightlyloosentheMountingPlatescrews.

•LockandunlockusingtheKey.

•ReattachControlWireandInteriorAssembly.

Page14

EMAIL:[email protected]

WEBSITE:www.honeywellsafes.com

ADDRESS:ConsumerAssistanceDept.

LHLicensedProducts,Inc.860EastSandhillAvenueCarson,CA90746USA

TELEPHONE:US/Canada1-877-354-5457(TollFree)

Mexico01-800-288-2872AfterEnglishvoicerecordingstopsyoumustthenenter800-

860-1677

tocompleteyourcall.(TollFree)

Australia0011-800-5325-7000(TollFree)

Germany/NewZealand00-800-5325-7000(TollFree)

OtherCountriesXX*-310-323-5722(TollChargesApply)

XX*-DialU.S.CountryCoderst

CALLCENTERHOURS:US/Canada7am–5pm(PST**)Mon–Fri(Subjecttochange)

CALLBACKHOURS:OtherCountries7am–8pm(PST**)Mon–Fri(Subjecttochange)

PST**-LocaltimeinLosAngeles,CA,USA

INTERNATIONALCALLBACKHOURS:

IfyouneedtospeakwithaconsumerassistantandcannotcontactusduringtheCall

Centerhoursabove,pleasesendanemailorleaveatelephonemessage,includingyour

Name, Telephone Number and the best time for us to contact you during the Call Back

hoursaboveandwewillmakeoureveryefforttocontactyouandhelpansweranyof

your questions or concerns.

*InsertcorrectCountryCode

**LocalTimebasedonLosAngelesCaliforniaUSA

CONSUMERASSISTANCE

Page15

2-3/8” (60mm) BACKSET

2-3/4” (70mm) BACKSET

THENDRILL1”(25mm)HOLE

INCENTERDOOROFEDGE

2”(50mm)INDEPTH

MARK

FOR1-3/4”

(45mm)

DOOR

DRILL

2-1/8”(54mm)

HOLE

MARK

FOR1-3/8”

(35mm)

DOOR

IMPORTANT!

PLACETEMPLATE

ONHIGHEDGEOF

DOORBEVEL

Page16

BACK OF

TEMPLATE

Page17

My Codes: Date Created

ProgrammingCode    (6digits)//

UserCode01     (4-8digits)//

UserCode02 (4-8digits)//

UserCode03 (4-8digits)//

UserCode04 (4-8digits)//

UserCode05 (4-8digits)//

UserCode06 (4-8digits)//

UserCode07 (4-8digits)//

UserCode08 (4-8digits)//

UserCode09 (4-8digits)//

UserCode10 (4-8digits)//

UserCode11 (4-8digits)//

UserCode12 (4-8digits)//

UserCode13 (4-8digits)//

UserCode14 (4-8digits)//

UserCode15 (4-8digits)//

UserCode16 (4-8digits)//

UserCode17 (4-8digits)//

UserCode18 (4-8digits)//

UserCode19 (4-8digits)//

UserCode20 (4-8digits)//

UserCode21 (4-8digits)//

UserCode22 (4-8digits)//

UserCode23 (4-8digits)//

UserCode24 (4-8digits)//

UserCode25 (4-8digits)//

Programming Record

Page18

TheHoneywellTrademarkisusedunderlicensefromHoneywellInternationalInc.Honeywell

InternationalInc.makesnorepresentationsorwarrantieswithrespecttothisproduct.

MDDBKPE-20160115www.honeywellsafes.com

Manufactured by:

LH Licensed Products, Inc.

860EastSandhillAvenue

Carson,CA90746

Lifetime Mechanical and Finish Warranty / 1 Year Limited Electronics Warranty

Thisproductcomeswithalifetimemechanicalandnishwarrantyandaoneyearlimited

electronicswarrantytotheoriginalresidentialconsumeragainstdefectsinmaterialand

workmanshipundernormaluseaslongastheoriginalresidentialpurchaseroccupiesthe

residentialpremisesuponwhichtheproductwasoriginallyinstalled.

ORIGINALRESIDENTIALCONSUMER

Thiswarrantyisnottransferable,andappliestotheoriginalpurchaseronly,aslongastheoriginal

purchaseroccupiestheresidentialpremisesuponwhichtheproduct(s)wasoriginallyinstalled.

Proofofpurchase(originalsalesreceipt)andownershipmustaccompanyallwarrantyclaims.

Allnon-homeownerpurchasers(includingpurchasersforindustrial,commercialandbusinessuse)

arenotcoveredunderthetermsofthiswarranty.

WHATISNOTCOVERED

Thiswarrantyisnullandvoidiftheproductwasusedforpurposesforwhichitwasnotdesigned.

ThiswarrantyDOESNOTCOVERnormalwearandtearofpartsordamageresultingfromanyof

thefollowing:negligentuse,misuseorabuseoftheproduct,orusecontrarytoorinviolationof

writteninstructionsprovidedbyLHLicensedProducts,Inc.Further,thiswarrantydoesnotcover

ActsofGod,suchasre,ood,hurricanesandtornadoes.ThiswarrantyDOESNOTCOVER

scratches,abrasions,deteriorationduetotheuseofpaints,solventsoruseofcleaners

containingabrasives,alcoholorothersolvents,whetherperformedbyacontractor,service

company,oryourself.ThiswarrantyDOESNOTCOVERproduct(s)usedincommercial

applications, used in common area applications, disassembly, repair or alteration by anyone other

than LH Licensed Products, Inc., improper installation or exposure to extremes of heat or humidity.

ThiswarrantyDOESNOTCOVERanylosses,injuriestopersonsorlossofproperty,general

damagesorcosts,andshippingandfreightexpensesrequiredtoreturnproduct(s)to

LH Licensed Products, Inc. LH Licensed Products, Inc. shall not be liable for any indirect,

incidental or consequential damages of any nature relating to this lock. LH Licensed Products, Inc.

isalsonotresponsibleforcostsassociatedwithremovingorreinstallingtheproduct.

ADDITIONALTERMS

LH Licensed Products, Inc. does not authorize any person to create for it any obligation or

liabilityinconnectionwiththeProduct.LHLicensedProducts,Inc.’smaximumliabilityhere

under is limited to the original purchase price of the Product. No action arising out of any claimed

breachofthiswarrantybyLHLicensedProducts,Inc.maybebroughtbytheoriginalresidential

purchasermorethanone(1)yearafterthecauseofactionhasarisen.

Honeywell 8712309 Installation guide

Honeywell 8712309 Installation guide

Honeywell 8712309 Installation guide

Related papers

Other documents