Thermo Fisher Scientific CTS Cellmation Incubator Software User guide

For Research Use or Manufacturing of Cell, Gene, or Tissue- Based

Products.

CTS™ Cellmation™ Incubator Software for

DeltaV™ System Installation

USER GUIDE

for use with: Thermo Scientiﬁc™ HeraCell™ VIOS™ CR CO2

Incubator

Catalog Number A59197

Publication Number MAN0029996

Revision A.0

Life Technologies Holdings Pte Ltd | Block 33 | Marsiling Industrial Estate Road 3 | #07-06, Singapore 739256

Revision history: (English)

Revision Date Description

A.0 25 September

2023 Initial release.

The information in this guide is subject to change without notice.

DISCLAIMER: TO THE EXTENT ALLOWED BY LAW, THERMO FISHER SCIENTIFIC INC. AND/OR ITS AFFILIATE(S) WILL NOT BE

LIABLE FOR SPECIAL, INCIDENTAL, INDIRECT, PUNITIVE, MULTIPLE, OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH OR

ARISING FROM THIS DOCUMENT, INCLUDING YOUR USE OF IT.

NOTICE TO PURCHASER: DISCLAIMER OF LICENSE: Purchase of this software product alone does not imply any license under any

process, instrument or other apparatus, system, composition, reagent or kit rights under patent claims owned or otherwise controlled by

Thermo Fisher Scientiﬁc, either expressly, or by estoppel.

TRADEMARKS: All trademarks are the property of Thermo Fisher Scientiﬁc and its subsidiaries unless otherwise speciﬁed.

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 3

TABLE OF CONTENTS

1 PURPOSE AND SCOPE ............................................................................................................................ 4

2 REFERENCES ............................................................................................................................................ 4

3 DEFINITIONS AND ACRONYMS ............................................................................................................... 4

4 SAFETY REQUIREMENTS ........................................................................................................................ 4

5 SOFTWARE INSTALLATION PROCEDURE ............................................................................................ 5

5.1 SIGNATURE LOG ........................................................................................................................................ 5

5.2 PREREQUISITES ......................................................................................................................................... 5

5.3 SOFTWARE INSTALLATION .......................................................................................................................... 7

6 SOFTWARE INSTALLATION VERIFICATION CHECKS........................................................................ 30

7 SAFETY .................................................................................................................................................... 31

8 DOCUMENTATION AND SUPPORT ....................................................................................................... 31

4 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

1 PURPOSE AND SCOPE

The purpose of this document is to provide instructions for installing the Gibco™ CTS™ Cellmation™

Incubator OPC UA Interface DeltaV™ software and DeltaV Live functionality.

This document will also detail the tests required to verify that the installed configuration has been

imported correctly.

2 REFERENCES

Document Name

Cellmation™ Common Module Software Installation Instructions

CTS™ Cellmation™ Xenon™ Software Release Notes

CTS™ Cellmation™ Common Software Release Notes

3 DEFINITIONS AND ACRONYMS

Term & (Acronym) Definition

GT Gene Therapy

SN Sentinel Monitor

HM Hold Monitor

EM Equipment Module

USM Unit Support Module

LND Landing Module

PH Phase

OAR Operator Action Request

MON Monitor

PCC Process Cell Class

INC Incubator

OPC UA Open Platform Communications United Architecture

I/O Input / Output

N/A Not Applicable

4 SAFETY REQUIREMENTS

N/A

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 5

5 SOFTWARE INSTALLATION PROCEDURE

These installation instructions are designed to be undertaken by a Thermo Fisher Service Engineer or

an engineer fully trained in DeltaV.

5.1 Signature Log

The signature log in Table 5-1 needs to be completed by all personnel involved in installing this

software before any work is commence.

Table 5-1 – Signature Log

Name (print)

Title

Initials

Signature

Date

5.2 Prerequisites

The prerequisites in Table 5-2 should be completed and signed-off before the software installation can

commence.

Table 5-1 – Prerequisites

Item

Number

Prerequisites Initials / Date

1. User installing the software must have full Windows Administrator Privileges

and DeltaV Administrator Privileges.

2. User must have access to ProfessionalPLUS Station.

3. If applicable, confirm that it is safe to proceed with the installation by following

the change management process.

4.

Ensure that there are no pending downloads required. Before installing

software, conduct a risk assessment to evaluate the impact of any required

downloads.

5. Ensure that the gateway is updated to the latest version.

Software Backup - ProfessionalPLUS

6 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

Item

Number Prerequisites Initials / Date

6.

Export the DeltaV Database.

• In DeltaV Explorer, right-click on the topmost level (i.e., the database

name).

• Note the location of the exported database below (this will differ

between clients and systems)

Path: ____________________________________________________

____________________________________________________

7.

Export the DeltaV Live Database.

• In DeltaV Graphics Studio, select the topmost level (i.e., the

database name) from the Graphics Explorer tab.

• From the “File” menu item, select “Export” and check the following:

• Note the location of the exported database below

Path: ____________________________________________________

____________________________________________________

Check for other CTS Cellmation Software installations if applicable.

8.

If there are no Thermo Fisher Scientific instruments on-site, refer to the

installation guide of the CTS Cellmation Common Software Installer and

confirm that the CTS Cellmation Common Software Module installation is

complete in the system.

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 7

Item

Number Prerequisites Initials / Date

9.

If there are previous CTS Cellmation Software installations on the system,

then a decision must be made as to which files need updating.

To check for installs, open Windows Control Panel and select

• “Programs ->“Programs and Features”

Check for any “gibco_CTS_Cellmation_...............” installs and note them

below

1. ____________________________________________________

2. ____________________________________________________

3. ____________________________________________________

4. ____________________________________________________

5. ____________________________________________________

10.

If a previous CTS Cellmation Common Software installation is present, then

refer to the latest release of the Common Installer and release note for any

updated common items to be installed.

Common Software items can be installed by following the instructions in the

Installation Guide of the Common Installer. Only the common items should be

overwritten.

11.

If any other previous CTS Cellmation Software installations are present, then

refer to the latest release of the instrument specific installer and release note

for any updated items to be installed.

Instrument specific software items can be installed by following the

instructions in the Installation Guide of the instrument specific installers; only

those items should be overwritten.

CTS Cellmation Incubator software items can be installed by following this

guide; only those items should be overwritten.

IMPORTANT: If you already have DeltaV configured for communication with other instruments, only

select “NO” when prompted about an update unless installing an updated version of the

module to ensure Cellmation’s installation does not negatively impact existing DeltaV

connections! This is the safest way to install Cellmation without risking existing configurations.

5.3 Software Installation

The steps shown in Table 5-3 should be performed on the DeltaV ProfessionalPLUS (ProPlus) station

using DeltaV Explorer.

This revision of the installation instructions is applicable to release 2.0.0.

8 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

IMPORTANT: The order of component installation listed below must be followed because there

are interdependencies to the imported files! If your installation is unsuccessful, you can retry your

import, but the step sequence should be maintained. Additionally, DO NOT delete any files on the

DeltaV computer that you did not import from the Cellmation Installation Folder.

Table 5-2 – Software Installation Instructions

Step Instructions Initials / Date

1.

Copy the Cellmation Incubator Installer Package into the folder

“D:\DeltaV\DVData\Import-Export” on the DeltaV computer. The Installer package

will include the installer .exe file and other required files/folders. DO NOT delete or

rename any files/folders in the installer package.

Execute the “gibco_CTS_Cellmation_Incubator_2.0.0.exe” and perform the

following to complete the installation:

• Right-click on the “gibco_CTS_Cellmation_Incubator_2.0.0.exe” file and

select “Run as administrator”.

• The welcome screen will appear. Click “Next >” once displayed on the

popup screen.

• Accept the terms of the License Agreement to proceed with the installation.

Click “Next >.”

• The pop-up displays the destination location for the software installation.

Click “Next >”.

• Enter Username, Company Name, and serial number (Reg Code received

with the installer). Click “Next >”.

• After entering a valid Reg Code, the “Install” button will be available. Click to

proceed with the installation. Click “Finish” once complete.

• If an invalid Reg Code is entered, it will show the error message “Invalid

registration code.” Click “OK” and re-enter the correct Reg Code to proceed.

Note: If the same version of the installer is already present on the system, then a

prompt will appear to uninstall the previous version. Select “OK” to continue

uninstallation and “Cancel” to exit uninstallation. Choose the appropriate option.

Otherwise, uninstall the previous installer before proceeding with the new

installation. Select “Control Panel > Programs and Features” to uninstall the

previous installer.

2.

After successful installation, a folder will be created entitled

“gibco_CTS_Cellmation_Incubator_2.0.0” with two subfolders, “Displays” and

“FHX,” in the Import-Export folder.

Also, this will automatically copy all the chart files present in the

“Displays/Charts_Incubator” folder to “D:\DeltaV\DVData\Charts\lib”.

Note: Upon uninstallation of the installer, all the created folders during installation

will be automatically deleted (The entire Installer folder

“gibco_CTS_Cellmation_Incubator_2.0.0” with subfolders and chart files copied

under “D:\DeltaV\DVData\Charts\lib” will get deleted).

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 9

Step Instructions Initials / Date

3.

Steps 4 through 12 provide instructions to import various packages of code directly

into the DeltaV library. The standard import flow is as follows:

• Open DeltaV Explorer (from Start menu under DeltaV Engineering)

• Navigate to File  Import  Standard DeltaV Format

• FHX files to import are located in D:\DeltaV\DVData\Import-Export\

gibco_CTS_Cellmation_Incubator_2.0.0\FHX

• Make sure to uncheck ‘Include the license information’ tick box before

confirming to import a component. Click Open.

• This will typically take around one minute. When done, “Import complete”

will appear.

• Note: When importing .fhx files into the database, there may be some file

conflicts that open a pop-up prompt.

• If importing for the first time, select “No to All”.

• If re-importing a file for any reason without deleting its previously

imported copy, make sure to read the pop-up.

4.

From DeltaV Explorer, import the Setup .fhx file from the “FHX” subfolder:

Module Name

gibco_Named_Sets_Incubator

10 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

Step Instructions Initials / Date

Confirm the following are imported into “ThermoGT_Incubator” Named Sets folder in

the database:

Named Set Name

INC_Active_Inactive

INC_Commands

INC_Cylinder_Status

INC_Door_Status

INC_HEPA_Config

INC_Link_Status

INC_ON_OFF

INC_SteriRun_Status

INC_Water_Level

• Located at DeltaV_System  System Configuration  Setup  Named

Sets  ThermoGT_Incubator

5.

From DeltaV Explorer, import the composite templates .fhx file from “FHX”

subfolder:

Module Name

gibco_Composites_Incubator

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 11

Step Instructions Initials / Date

Confirm the following modules have been imported into the “ThermoGT_Incubator”

folder:

IMPORTANT: The internal revision, in the INTERNAL_REV parameter, for each

module should match the revision documented below:

Module Name Rev Installed Rev

GT_INC_ABORT 0.2

GT_ INC_FAIL_MON 0.2

GT_ INC_HOLD 0.2

GT_ INC_RESTART 0.2

GT_ INC_STOP 0.2

GT_ INC_ALM_MSG 0.3

• Located at DeltaV_System  Library  Composite Templates 

ThermoGT_Incubator

• To locate the internal revision values, select each module and find the

INTERNAL_REV parameter from the listed parameters.

6.

From DeltaV Explorer, import the Control Modules Classes .fhx file from the “FHX”

subfolder:

Module Name

gibco_Control_Module_Classes_Incubator

Confirm the following modules have been imported into the “ThermoGT” folder:

Note the internal revision in the INTERNAL_REV parameter for each module which

should match the revision documented below:

Module Name Rev Installed Rev

GT_INCUBTR_LAND 0.4

• Located at DeltaV_System  Library  Advanced Definitions  Control

Module Classes  ThermoGT

• To locate the internal revision values, select each module and find the

INTERNAL_REV parameter from the listed parameters.

12 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

Step Instructions Initials / Date

7.

From DeltaV Explorer, import the Equipment Modules Classes .fhx file from the

“FHX” subfolder:

Module Name

gibco_Equipment_Module_Class_Incubator

Confirm the following modules have been imported into the “ThermoGT” folder:

Note the internal revision in the INTERNAL_REV parameter for each module should

match the revision documented below:

Module Name Rev Installed Rev

GT_INCUBTR_EM 0.3

• Located at DeltaV_System  Library  Advanced Definitions 

Equipment Module Classes  ThermoGT

• To locate the internal revision values, select each module and find the

INTERNAL_REV parameter from the listed parameters.

8.

From DeltaV Explorer, import the Phase Classes .fhx file from the “FHX” sub folder:

Module Name

gibco_Phase_Classes_Incubator

Confirm the following phases have been imported into the “ThermoGT” folder:

Note the internal revision in the INTERNAL_REV parameter for each module should

match the revision documented below:

Module Name Rev Installed Rev

GT_INC_INIT 0.2

GT_INC_PROMPT 0.2

• Located at DeltaV_System  Library  Advanced Definitions  Phase

Classes  ThermoGT

• To locate the internal revision values, select each module and find the

INTERNAL_REV parameter from the listed parameters.

9.

From DeltaV Explorer, import the Unit Classes .fhx file from the “FHX” subfolder:

Module Name

gibco_Unit_Class_Incubator

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 13

Step Instructions Initials / Date

Confirm the following modules have been imported into the “ThermoGT” folder:

Note the internal revision in the INTERNAL_REV parameter for each module should

match the revision documented below:

Module Name Rev Installed Rev

INCUBATR_UC 0.2

• Located at DeltaV_System Library Advanced Definitions Unit

Classes ThermoGT

• To locate the internal revision values, select each module and find the

INTERNAL_REV parameter from the listed parameters.

10.

From DeltaV Explorer, import the Operations .fhx file from the “FHX” subfolder:

File Name

ThermoGT_Operations_Incubator

ThermoGT_UnitProcedures_Incubator

Confirm the following recipes have been imported into the “ThermoGT” folder:

Note the version for each recipe should match the version documented below:

Recipe Name

OP_INC_ACQ_REL

OP_INC_INIT_SETUP

OP_INC_STERI_RUN_STRT

OP_INC_STERI_RUN_END

• Located at DeltaV_System  System Configuration  Recipes 

Operations  ThermoGT

Recipe Name

UP_INC_RUN

• Located at DeltaV_System  System Configuration  Recipes  Unit

Procedures  ThermoGT

14 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

Step Instructions Initials / Date

Create Unit Instance

11.

Edit the file ‘gibco_INCXXXX-AREA.fhx’ in Notepad.

Note: XXXX is correct nomenclature at this point.

• Replace “INCXXXX” with the incubator tag specified for the instrument

within DeltaV and save the file with a new name identifying it with the new

tag.

• It is highly recommended to use Find and Replace to catch all instances to

update “INCXXXX” to “INC” plus the last 4 digits of the instrument serial

number.

• Repeat this step for additional incubator unit instances as required.

12.

Import the file with the new tag name into DeltaV.

• To confirm the import, verify that a new area and included modules are

located at DeltaV Explorer  DeltaV System  System Configuration 

Control Strategies

13.

Assign the following modules to the required controller. (Note INCXXXX below is

replaced with the new tag name)

• INCXXXX

• INCXXXX-INC-EM

• INCXXXX-INC-USM

• To assign modules:

• Drill-down to the unit module (DeltaV_System  System Configuration

 Control Strategies  INCXXXX-AREA [area]  INCXXXX-PC

[process cell]  INCXXXX [unit]

• Right-click on each module listed above and select Properties.

• Navigate to the Tools tab and select Assign Now.

Assign to the appropriate controller and answer Yes to confirm the

prompt.

14.

Assign the following module to the required EIOC/Application Station. (Note

INCXXXX below is replaced with the new tag name)

• INCXXXX-INC-LND

• To assign modules:

• Drill-down to the unit module (DeltaV_System  System Configuration

 Control Strategies  INCXXXX-AREA [area]  INCXXXX-PC

[process cell]  INCXXXX [unit]

• Right-click on the module listed above and select Properties.

• Navigate to the Tools tab and select Assign Now.

• Assign to the appropriate EIOC controller and answer Yes to confirm

the prompt.

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 15

Step Instructions Initials / Date

15.

Assign the following Area to the Alarms and Events of the ProPlus/required

Workstation/Sever, Continuous Historian and Batch Executive (Note INCXXXX

below is replaced with the new tag name.)

• INCXXXX-AREA

• Assign area to the Alarms and Events:

• Drill-down to the ProPlus/Workstation (Physical Network  Control

Network  ProPlus Station/Workstation/Server  Alarms and

Events

• Right-click and select Assign Area.

• Select INCXXXX-AREA and select Yes when prompted.

• Assign area to the Continuous Historian:

• Drill-down to the Continuous Historian (Physical Network  Control

Network  ProPlus Station/Workstation/Server  Continuous

Historian

• Right-click and select Assign Area

• Select INCXXXX-AREA and select Yes when prompted

• Assign area to Batch Executive:

• Drill-down to the Batch Executive (Physical Network  Control

Network  ProPlus Station/Workstation/Server  Batch Executive

 Assigned Areas

• Right-click and select Assign Area.

• Select INCXXXX-AREA and select Yes when prompted.

16.

Assign the following Recipes to the Batch Executive:

• Assign Recipe to the Batch Executive:

• Drill-down to the Batch Executive (Physical Network  Control

Network  ProPlus Station/Workstation  Batch Executive 

Assigned Recipes

• Right-click and select Recipe.

• Select OP_INC_ACQ_REL and select Yes when prompted.

• Similarly assign other operations OP_INC_ACQ_REL,

OP_INC_INIT_SETUP, OP_INC_STERI_RUN_STRT,

OP_INC_STERI_RUN_END and Unit Procedure “UP_INC_RUN”

16 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

Step Instructions Initials / Date

17.

Download as follows:

• Download the Setup data of the ProPlus/Workstation/Server for the area

added under Alarms and Events.

• Right-click on the ProPlus/Workstation/Server and select Download

 Setup Data

• Select Yes when prompted to confirm the download.

• Download the Continuous Historian for the area added:

• Right-click on the Continuous Historian and select Download 

Continuous Historian

• Select Yes when prompted to confirm the download.

• Download the Batch Executive for the area added and recipe assigned:

• Right-click on the Batch Executive and select Download  Batch

Executive

• Select Yes when prompted to confirm the download.

OPC UA IO installation

18.

The OPC UA PDT/LDT configuration is contained within the file

‘gibco_Incubator_PDT_INCXXXX.fhx’ in the “FHX” subfolder. This file and the area

file can be edited so that it imports the required tag information. Using the Find and

Replace search function is recommended to make all required changes within the

gibco_Incubator_PDT_INCXXXX.fhx file.

The OPC UA I/O has been assigned to an EIOC named “EIOC1” by default.

• If the I/O is to be assigned to another EIOC/App Station, then replace all

instances of “EIOC1” in the .fhx file with the desired name of the EIOC or

Application Station.

• Replace “INCXXXX” with the Incubator tag specified for the instrument

within DeltaV.

• Save the file with a new name identifying it with the new tag.

• Repeat this step for additional Incubator unit instances as required.

19.

Ensure the OPC UA Client has been set up for the OPC UA protocol.

If the OPC UA I/O is being assigned to an EIOC, ensure the ethernet port P01

protocol has been set to OPC UA.

• Navigate to DeltaV_System  System Configuration  Physical Network

 Control Network  I/O Network  EIOC Name  P01

• Right-click P01 and select Properties.

• Under the Advanced tab, select OPC UA from the Interface  Protocol

drop-down.

If the OPC UA I/O is being assigned to an Application Station:

• Navigate to DeltaV_System  System Configuration  Physical Network

 Control Network  Control Network  Application Station Name 

OPC UA Client

• Right-click OPC UA Client and select Properties.

• Under the General tab, set the checkbox to “enable OPC UA client”.

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 17

Step Instructions Initials / Date

20. Import the ‘gibco_OPCUA_Incubator_PDT_INCXXXX.fhx’ file with the assigned tag

name into DeltaV.

21.

Set the IP address of the Incubator OPC UA server.

If the OPC UA I/O is being assingned to an EIOC

• Navigate to DeltaV_System  System Configuration  Physical Network

 Control Network  I/O Network  EIOC Name  P01

If the OPC UA I/O is being assigned to an Application Station

• Navigate to DeltaV_System  System Configuration  Physical Network

 Control Network  Control Network  Application Station Name 

OPC UA Client

From here right click on the Rotea PDT that has been imported and select the

Primary tab.

• Change the default IP address to match the IP address set in the Incubator.

• Note the port number 4840 is the Incubator default port and should not be

changed.

22.

Download the unit module and contained modules. No errors should be reported.

(Note INCXXXX below is replaced with the new tag name)

• Navigate to the INCXXXX unit module (DeltaV Explorer  DeltaV_System

 System Configuration  Control Strategies  INCXXXX-AREA 

INCXXXX-PC  INCXXXX

• Right-click the INCXXXX unit module and select Download  Unit module

and contained modules

• Select Yes when prompted to confirm the download.

23.

If ProPlus/Workstation/Server Setup data has already been downloaded in step 17,

skip this step.

Download the Setup data of the ProPlus/Controllers/Workstation/Server for all the

named sets.

• Navigate to DeltaV Explorer  DeltaV System  System Configuration 

Physical Network  ProPlus/Controllers/Workstation/Server

• Right-click the ProPlus/Controllers/ Workstation/Server and select

Download  Setup Data

• Select Yes when prompted to confirm the download.

18 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

Step Instructions Initials / Date

24.

Download the OPC IO. There should not be errors except for with a secodary

connection and/or Application Certificate, which can be ignored.

EIOC assigned IO

• Navigate to DeltaV Explorer  DeltaV System  System Configuration 

Physical Network  Control Network  I/O Network  EIOC Name  P01

• Right-click the port P01 and select Download Ethernet I/O Port

Application Station assigned IO

• Navigate to DeltaV Explorer  DeltaV System  System Configuration 

Physical Network  Control Network  Application Station Name 

OPC UA Client

• Right-click OPC UA Client and select Download OPC UA Client.

Establishing OPC UA Communication

25.

On the DeltaV Computer, using DeltaV Explorer

EIOC assigned IO

Assign the predetermined IP address to the ethernet port P01 and generate a

certificate.

• Navigate to DeltaV_System  System Configuration  Physical Network

Control Network  I/O Network  EIOC Name  P01

• Right-click P01 and select Properties.

• In the Advanced tab, input the predetermined IP address of the DeltaV

System under Primary Connection IP Address.

• In the Certificate tab, select Generate to create a new certificate.

• Click OK to save the changes and close the pop-up dialog box.

Application Station assigned IO

• Open the Windows Control Panel and select Control Panel\Network and

Internet\Network Connections.

• Select the Network Interface Card (NIC) to be used as the OPC UA network

connection and set the TCP/IPv4 IP address to the predetermined IP

address of the DeltaV System.

• Navigate to DeltaV Explorer  DeltaV System  System Configuration 

Physical Network  Control Network  Application Station Name 

OPC UA Client

• Right-click OPC UA Client and select Properties.

• In the Certificate tab, select Generate to create a new certificate.

• Click OK to save the changes and close the pop-up dialog box.

Note: If the ethernet port P01 or Application Station OPC UA Client is already

assigned to the predetermined IP address and a certificate is generated, skip this

step.

CTSTM CellmationTM Incubator Software for DeltaVTM System Installation User Guide 19

Step Instructions Initials / Date

26.

Perform a factory reset of the incubator gateway device

a. Connect the USB Micro (slot C) on the incubator Gateway to the USB Type

A port of a Windows PC.

b. Press the reset button (S1) lightly (you should be able to feel a ‘click’ when

pressing it). Then, press and hold for > 20 seconds. Observe that the LED

light will blink in red, until it turns green. Release S1 button.

20 CellmationTM Incubator Software for DeltaVTM System Installation User Guide

Configure the static IP address of the incubator Gateway and download

gateway OPC UA certificate

a. From the PC, open a web browser (Microsoft Edge, Google Chrome,

Mozilla Firefox, etc.) and enter the address https://192.168.7.1 and press

Enter.

Note: You may need to refresh a few times until the page below is loaded.

b. Select “Proceed to 192.168.7.1 (unsafe)”

c. In the web interface, the OPC UA Server IP address, the user name and the

password can be configured. This is important so that the OPC UA Server

can be integrated in the customer network and an OPC UA Client, e.g.,

DeltaV system, can read out the data.

d. Enter the predetermined information for the following fields:

o IP-configuration (Select: Static)

o IPv4 Address

o SubNet Mask

o OPC-Username

o OPC-Password

o Update Server Password

o Repeat Update Server Password

Page is loading ...

Thermo Fisher Scientific CTS Cellmation Incubator Software User guide

Thermo Fisher Scientific CTS Cellmation Incubator Software User guide

Related papers

Other documents