2. Toro
  3. Beacon Kit, RT600 or RT1200 Trencher

Toro Beacon Kit, RT600 or RT1200 Trencher Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Toro Beacon Kit, RT600 or RT1200 Trencher Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
FormNo.3394-714RevA
BeaconLightKit
RT600orRT1200Trencher
ModelNo.25415
ModelNo.25415E
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachine
fromthenormaloperatingposition.
Safety
WARNING
CALIFORNIA
Proposition65Warning
Thisproductcontainsachemicalorchemicals
knowntotheStateofCaliforniatocausecancer,
birthdefects,orreproductiveharm.
SafetyandInstructional
Decals
Safetydecalsandinstructionsareeasily
visibletotheoperatorandarelocatednear
anyareaofpotentialdanger.Replaceany
decalthatisdamagedorlost.
120–0771
1.BeaconLight
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Preparingthemachine.
2
Decal1
Locatingmountingholesanddecal
placement.
BeaconLight1
BeaconLightMount(RT600only)
1
Bolt3/8x6inches(RT600only)
2
Washerhardened(RT600only)
2
3
Flangenut(RT600only)
2
Mountingthebeaconlight.
4
WiringHarness1
Connectingthewiringharnesstothe
machine.
Switch
1
5
SwitchBoot
1
ConnectingOn/Offswitchandrouting
thewiringharnesstobeaconlight.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3394-714*A
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Movethemachinetoalevelsurface.
2.Settheparkingbrake,shutofftheengine,andremove
thekeyfromthekeyswitch.
3.Removetherightsidepanel;refertotheOperator’s
Manual.
4.Disconnectthebattery;refertotheOperator’sManual.
2
LocatingMountingHolesand
DecalPlacement
Partsneededforthisprocedure:
1Decal
Procedure
1.Locateandmarktheswitchholelocationforyour
specicmodel(Figure1orFigure2).
2.Drilltheindicatedholesizeatthelocationyoumarked.
3.Locatethepositionandapplythebeaconlightdecal
foryourspecicmodel(Figure1orFigure2).
Note:Stopdrillingimmediatelyaftercompletely
penetratingthesurface.
Figure1
RT600
1.6mm(0.25inch)4.35mm(1.375inch)
2.66mm(2.5inch)5.6mm(0.25inch)
3.13mm(0.5inchDiameter)
2
Figure2
RT1200
1.9mm(0.35inch)4.16mm(0.625inch)
2.44mm(1.75inch)5.4mm(0.15inch)
3.13mm(0.5inch)
1.Locateandmarkthebeaconholelocation(Figure3).
2.Drilltheindicatedholesizeatthemarkedlocation.
Note:Stopdrillingimmediatelyaftercompletely
penetratingthesurface.
Figure3
RT1200
1.318mm(12.5inch)3.22mm(0.875inch
diameter)
2.127mm(5inch)
3
MountingtheBeaconLight
Partsneededforthisprocedure:
1BeaconLight
1
BeaconLightMount(RT600only)
2
Bolt3/8x6inches(RT600only)
2
Washerhardened(RT600only)
2
Flangenut(RT600only)
MountingthebeaconlighttotheRT600
1.Usetheincludedhardwaretomountthebeaconlight
mountingbrackettoptheROPS(Figure4).
2.Removethemountinghardwarefromthethreaded
shaftonthebeaconlightandinserttheshaftintothe
beaconlightmounthole(Figure4).
3
3.Installthemountinghardwarebackontothethreaded
shaftandtightenuntilsecure.Donotover-tightenthe
retaininghardware.
Figure4
RT600
1.Beaconlight4.Washerhardened
2.Beaconlightmounting
bracket
5.Bolt(3/8x6inches)
3.Flangenut(3/8inch)
Mountingthebeaconlighttothe
RT1200
1.Removethemountinghardwarefromthethreaded
shaftonthebeaconlight.
2.Placetheshaftofthebeaconlightthroughthe
mountingholeinthecanopy(Figure5).
3.Installthemountinghardwarebackontothethreaded
shaftandtightenuntilsecure.Donotover-tightenthe
retaininghardware.
Figure5
RT1200
1.Beaconlightthreaded
shaft
2.Beaconlightmounting
hole
4
ConnectingtheWiring
HarnesstotheMachine
Partsneededforthisprocedure:
1WiringHarness
Procedure
1.Behindthebattery-disconnectswitchontherightside
ofthemachine,removeoneinsulatorlug,nut,and
lock-washerfromtheterminalfurthestawayfromthe
engine(Figure6orFigure7).
2.Usingthehardwareremoved,attachoneringterminal
ofthewireharnesstotheterminalfurthestawayfrom
theengine(Figure6orFigure7).
4
Figure6
RT600
1.InsulatorLug4.Ring-terminal
2.Nut5.Positiveterminal
3.Lock-washer6.Batery-disconnectswitch
Figure7
RT1200
1.InsulatorLug4.Ring-terminal
2.Nut5.Positiveterminal
3.Lock-washer6.Batery-disconnectswitch
3.Removetheboltattachedtotheengineground.(Figure
8orFigure9).
4.Usingtheboltyouremoved,attachtheotherring
terminaltotheengineground(Figure8orFigure9).
5
Figure8
RT600
1.Bolt3.Engineground
2.Ringterminal
Figure9
RT1200
1.Battery-disconnectswitch3.Engineground
2.Bolt4.Ringterminal
5
ConnectingOn/OffSwitchand
RoutingtheWiringHarnessto
BeaconLight
Partsneededforthisprocedure:
1
Switch
1
SwitchBoot
Procedure
1.Ifequipped,removethepanelbeneaththedashboard
(Figure10).
Figure10
1.Bolt2.Kickerpanel
2.Routethewiringharnesstotheoperatorareaand
underneaththedashboard(Figure12orFigure13).
3.Removethemountinghardwarefromthethreaded
shaftoftheswitch,androutetheswitchtothe
undersideofthemountinghole.
4.Installthemountinghardwarebackontothethreaded
shaftandtightenuntilsecure.Donotover-tighten
retainingthehardware.
5.Installtheswitchbootoverthetoggle.
6
Figure11
RT1200Shown
1.SwitchBoot2.BeaconLightSwitch
6.Routetheremainderofthewiringharnessunderneath
theoperatorareaandconnectittothebeaconlight
(Figure12orFigure13).Ifnecessary,removethefoot
plate;refertotheOperator’sManual.
7.Usetheprovidedmagneticcabletiemountsand
additionalcabletieswhererequiretoproperlysecure
thewiringharness.
Figure12
RT600
1.RecommendedwiringharnessroutefortheRT600.
Figure13
RT1200
1.RecommendedwiringharnessroutefortheRT1200.
8.Installanypartsyouremoved,reconnectthebattery,
androtatethebattery-disconnectswitchtotheOn
position,ifequipped.
7
Operation
UsingtheBeaconLight
1.ToggletheswitchfromtheOffpositiontoturnthe
beaconlighton.
2.ReturntheswitchtotheOffpositiontoturnthe
beaconlightoff.
Note:Rotatethebeaconlightswitch180degreestoachieve
thedesireOnorOffposition.
8
/