Toro Beacon Kit, RT600 or RT1200 Trencher Installation guide

Toro
Brand
Toro
Model
Beacon Kit, RT600 or RT1200 Trencher
Type
Installation guide

Toro Beacon Kit, RT600 or RT1200 Trencher, is designed to enhance safety and visibility while operating your trencher. This beacon light kit provides a bright and attention-grabbing signal, making it easier for others to see your machine, especially in low-light conditions or on busy jobsites. It can be conveniently mounted on the ROPS of your trencher, ensuring 360-degree visibility. Installation is simple and straightforward, with all necessary hardware included. The beacon light is activated by an on/off switch, allowing you to control its operation easily.

Toro Beacon Kit, RT600 or RT1200 Trencher, is designed to enhance safety and visibility while operating your trencher. This beacon light kit provides a bright and attention-grabbing signal, making it easier for others to see your machine, especially in low-light conditions or on busy jobsites. It can be conveniently mounted on the ROPS of your trencher, ensuring 360-degree visibility. Installation is simple and straightforward, with all necessary hardware included. The beacon light is activated by an on/off switch, allowing you to control its operation easily.

FormNo.3394-714RevA
BeaconLightKit
RT600orRT1200Trencher
ModelNo.25415
ModelNo.25415E
InstallationInstructions
Note:Determinetheleftandrightsidesofthemachine
fromthenormaloperatingposition.
Safety
WARNING
CALIFORNIA
Proposition65Warning
Thisproductcontainsachemicalorchemicals
knowntotheStateofCaliforniatocausecancer,
birthdefects,orreproductiveharm.
SafetyandInstructional
Decals
Safetydecalsandinstructionsareeasily
visibletotheoperatorandarelocatednear
anyareaofpotentialdanger.Replaceany
decalthatisdamagedorlost.
120–0771
1.BeaconLight
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescription
Qty.
Use
1
Nopartsrequired
–
Preparingthemachine.
2
Decal1
Locatingmountingholesanddecal
placement.
BeaconLight1
BeaconLightMount(RT600only)
1
Bolt3/8x6inches(RT600only)
2
Washerhardened(RT600only)
2
3
Flangenut(RT600only)
2
Mountingthebeaconlight.
4
WiringHarness1
Connectingthewiringharnesstothe
machine.
Switch
1
5
SwitchBoot
1
ConnectingOn/Offswitchandrouting
thewiringharnesstobeaconlight.
©2015—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.
OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved
*3394-714*A
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Movethemachinetoalevelsurface.
2.Settheparkingbrake,shutofftheengine,andremove
thekeyfromthekeyswitch.
3.Removetherightsidepanel;refertotheOperator’s
Manual.
4.Disconnectthebattery;refertotheOperator’sManual.
2
LocatingMountingHolesand
DecalPlacement
Partsneededforthisprocedure:
1Decal
Procedure
1.Locateandmarktheswitchholelocationforyour
specicmodel(Figure1orFigure2).
2.Drilltheindicatedholesizeatthelocationyoumarked.
3.Locatethepositionandapplythebeaconlightdecal
foryourspecicmodel(Figure1orFigure2).
Note:Stopdrillingimmediatelyaftercompletely
penetratingthesurface.
Figure1
RT600
1.6mm(0.25inch)4.35mm(1.375inch)
2.66mm(2.5inch)5.6mm(0.25inch)
3.13mm(0.5inchDiameter)
2
Figure2
RT1200
1.9mm(0.35inch)4.16mm(0.625inch)
2.44mm(1.75inch)5.4mm(0.15inch)
3.13mm(0.5inch)
1.Locateandmarkthebeaconholelocation(Figure3).
2.Drilltheindicatedholesizeatthemarkedlocation.
Note:Stopdrillingimmediatelyaftercompletely
penetratingthesurface.
Figure3
RT1200
1.318mm(12.5inch)3.22mm(0.875inch
diameter)
2.127mm(5inch)
3
MountingtheBeaconLight
Partsneededforthisprocedure:
1BeaconLight
1
BeaconLightMount(RT600only)
2
Bolt3/8x6inches(RT600only)
2
Washerhardened(RT600only)
2
Flangenut(RT600only)
MountingthebeaconlighttotheRT600
1.Usetheincludedhardwaretomountthebeaconlight
mountingbrackettoptheROPS(Figure4).
2.Removethemountinghardwarefromthethreaded
shaftonthebeaconlightandinserttheshaftintothe
beaconlightmounthole(Figure4).
3
3.Installthemountinghardwarebackontothethreaded
shaftandtightenuntilsecure.Donotover-tightenthe
retaininghardware.
Figure4
RT600
1.Beaconlight4.Washerhardened
2.Beaconlightmounting
bracket
5.Bolt(3/8x6inches)
3.Flangenut(3/8inch)
Mountingthebeaconlighttothe
RT1200
1.Removethemountinghardwarefromthethreaded
shaftonthebeaconlight.
2.Placetheshaftofthebeaconlightthroughthe
mountingholeinthecanopy(Figure5).
3.Installthemountinghardwarebackontothethreaded
shaftandtightenuntilsecure.Donotover-tightenthe
retaininghardware.
Figure5
RT1200
1.Beaconlightthreaded
shaft
2.Beaconlightmounting
hole
4
ConnectingtheWiring
HarnesstotheMachine
Partsneededforthisprocedure:
1WiringHarness
Procedure
1.Behindthebattery-disconnectswitchontherightside
ofthemachine,removeoneinsulatorlug,nut,and
lock-washerfromtheterminalfurthestawayfromthe
engine(Figure6orFigure7).
2.Usingthehardwareremoved,attachoneringterminal
ofthewireharnesstotheterminalfurthestawayfrom
theengine(Figure6orFigure7).
4
Figure6
RT600
1.InsulatorLug4.Ring-terminal
2.Nut5.Positiveterminal
3.Lock-washer6.Batery-disconnectswitch
Figure7
RT1200
1.InsulatorLug4.Ring-terminal
2.Nut5.Positiveterminal
3.Lock-washer6.Batery-disconnectswitch
3.Removetheboltattachedtotheengineground.(Figure
8orFigure9).
4.Usingtheboltyouremoved,attachtheotherring
terminaltotheengineground(Figure8orFigure9).
5
Figure8
RT600
1.Bolt3.Engineground
2.Ringterminal
Figure9
RT1200
1.Battery-disconnectswitch3.Engineground
2.Bolt4.Ringterminal
5
ConnectingOn/OffSwitchand
RoutingtheWiringHarnessto
BeaconLight
Partsneededforthisprocedure:
1
Switch
1
SwitchBoot
Procedure
1.Ifequipped,removethepanelbeneaththedashboard
(Figure10).
Figure10
1.Bolt2.Kickerpanel
2.Routethewiringharnesstotheoperatorareaand
underneaththedashboard(Figure12orFigure13).
3.Removethemountinghardwarefromthethreaded
shaftoftheswitch,androutetheswitchtothe
undersideofthemountinghole.
4.Installthemountinghardwarebackontothethreaded
shaftandtightenuntilsecure.Donotover-tighten
retainingthehardware.
5.Installtheswitchbootoverthetoggle.
6
Figure11
RT1200Shown
1.SwitchBoot2.BeaconLightSwitch
6.Routetheremainderofthewiringharnessunderneath
theoperatorareaandconnectittothebeaconlight
(Figure12orFigure13).Ifnecessary,removethefoot
plate;refertotheOperator’sManual.
7.Usetheprovidedmagneticcabletiemountsand
additionalcabletieswhererequiretoproperlysecure
thewiringharness.
Figure12
RT600
1.RecommendedwiringharnessroutefortheRT600.
Figure13
RT1200
1.RecommendedwiringharnessroutefortheRT1200.
8.Installanypartsyouremoved,reconnectthebattery,
androtatethebattery-disconnectswitchtotheOn
position,ifequipped.
7
Operation
UsingtheBeaconLight
1.ToggletheswitchfromtheOffpositiontoturnthe
beaconlighton.
2.ReturntheswitchtotheOffpositiontoturnthe
beaconlightoff.
Note:Rotatethebeaconlightswitch180degreestoachieve
thedesireOnorOffposition.
8
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Toro Beacon Kit, RT600 or RT1200 Trencher Installation guide

Toro
Brand
Toro
Model
Beacon Kit, RT600 or RT1200 Trencher
Type
Installation guide

Toro Beacon Kit, RT600 or RT1200 Trencher, is designed to enhance safety and visibility while operating your trencher. This beacon light kit provides a bright and attention-grabbing signal, making it easier for others to see your machine, especially in low-light conditions or on busy jobsites. It can be conveniently mounted on the ROPS of your trencher, ensuring 360-degree visibility. Installation is simple and straightforward, with all necessary hardware included. The beacon light is activated by an on/off switch, allowing you to control its operation easily.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents