TANDBERG D1320202 User manual

Brand: TANDBERG

Model: D1320202

Type: User manual

This manual is also suitable for

Network Router D1320202

TANDBERG Network Router D1320202

The TANDBERG Network Router D1320202 is a powerful and versatile networking device that offers a wide range of features and capabilities. With its advanced routing capabilities such as VLAN support, QoS, and firewall protection. The router is ideal for use in small and medium-sized businesses, and can be used to connect multiple devices such as computers, printers, and servers to the internet and to each other.

The D1320202 is also equipped with a number of security features, including stateful packet inspection, denial-of-service protection, and intrusion detection, which help to protect your network from malicious attacks. Additionally, the router supports Quality of Service (QoS) features, which allow you to prioritize traffic and ensure that critical applications such as VoIP and video conferencing receive the bandwidth they need.

TANDBERG Network Router D1320202

TANDBERG GW Data port Command Interface User Guide

TANDBERG 3G GW

Data port Command Interface User Guide

Software version R2

D1320202

TANDBERG

TANDBERG GW Data port Command Interface User Guide

Table of Contents

1. INTRODUCTION...........................................................................................................................3

2. CONNECTING TO THE DATA PORT COMMAND INTERFACE THROUGH THE RS-

232 PORT..................................................................................................................................................

2.1. HARDWARE AND CABLING............................................................................................................4

2.2. TROUBLESHOOTING ......................................................................................................................5

3. CONNECTING TO THE DATA PORT COMMAND INTERFACE USING TELNET.........6

4. THE TANDBERG 3G GATEWAY COMMANDS .....................................................................7

4.1. INTRODUCTION .............................................................................................................................7

4.1.1. Command format.....................................................................................................................7

4.1.2. Command types .......................................................................................................................7

4.2. THE COMMANDS ...........................................................................................................................8

4.2.1. System Configuration Commands ...........................................................................................9

4.2.2. General GW Commands........................................................................................................14

4.2.3. System Status Commands ......................................................................................................21

4.2.4. Debug Commands .................................................................................................................27

4.2.5. Special Commands ................................................................................................................27

4.3. INDEX COMMANDS .....................................................................................................................32

TANDBERG GW Data port Command Interface User Guide

1. Introduction

The TANDBERG GW Data port Command Interface User Guide contains guidelines on how

to use the textual command interface supported by the GW. The Data port Command

Interface can be accessed through Telnet via the LAN interface or through RS-232 by

connecting a serial cable to the serial interface connector, referred to as the Data port (ref.

chapter

2). Three Telnet sessions can be connected to the GW at the same time in addition to

the RS-232 connection.

If, after reading this manual, you require additional information concerning the use of the

TANDBERG GW Data port Command Interface, please contact your local TANDBERG

dealer who will be able to supply you with relevant information for special applications.

TANDBERG GW Data port Command Interface User Guide

2. Connecting to the Data port Command Interface through the

RS-232 port.

The RS-232 port is a 9-pin, female, D-sub connector located on the front of the GW. The port

is configured as a DCE (Data Communications Equipment). The RS-232 port is default set to

115200 baud, 8 data bits, none parity and 1 stop bit from factory. The RS-232 port is also

referred to as the Data port.

2.1. Hardware and Cabling

The pin outs for the RS-232 are defined in the following table (the DTE, Data Terminal

Equipment, could be a PC or other device capable of serial communication).

Pin no Signal Description Direction

1 CD Carrier detect To DTE

2 RD Receive data To DTE

3 TD Transmit data From DTE

4 DTR Data terminal ready From DTE

5 Ground

6 DSR Data set ready To DTE

7 RTS Ready to send From DTE

8 CTS Clear to send To DTE

9 RI Ring indicator To DTE

NOTE! A straight through cable should be used between the TANDBERG GW’s RS-232 port

and the DTE.

The figure below illustrates the recommended cable-wiring scheme for connecting the GW to

a PC through RS-232.

DTR and RTS are ignored. DSR, CD, and CTS are always asserted, while RI is not used.

TANDBERG GW PC

DCE, 9 pin DTE, 9 pin

1 CD 1 CD

2 RD 2 RD

3 TD 3 TD

4 DTR 4 DTR

5 GND 5 GND

6 DSR 6 DSR

7 RTS 7 RTS

8 CTS 8 CTS

9 RI 9 RI

TANDBERG GW Data port Command Interface User Guide

2.2. Troubleshooting

If communication cannot be established between the PC/terminal and the TANDBERG GW’s

Data port the following should be checked:

• Verify that the serial cable is a straight through 9-pin to 9-pin cable

• Confirm that the configuration of the PC/terminal’s serial RS-232 port is identical to

the configuration of the TANDBERG GW RS-232 port.

• Verify that the PC/terminal’s serial RS-232 port is working properly by connecting it

back-to-back to another PC/terminal and send characters in both directions

It requires a null-modem cable to perform this test

TANDBERG GW Data port Command Interface User Guide

3. Connecting to the Data port Command Interface using Telnet

The TANDBERG 3GW has one LAN port.

The GW’s Telnet server provides access to the Data port Command Interface through a

10/100 base T network interface supporting the TCP/IP protocol.

When connected to the 3G Gateway, type tsh to start a t-shell from the command line. The

Telnet client will receive a welcome message similar to the following:

Welcome to TANDBERG

TANDBERG 3G Gateway Release R2.0 customer

SW Release Date: 2006-03-28

NOTE! If the TANDBERG 3GW is protected by an IP password you will be prompted to enter

this password before you can access the Data port Command Interface via Telnet.

TANDBERG GW Data port Command Interface User Guide

4. The TANDBERG 3G Gateway Commands

4.1. Introduction

Typing ‘?’ or ‘help’ when connected to the Data Port Command Interface will return a list of

valid commands. The commands are used to control the functions of the 3G Gateway. A

command may be followed by a set of parameters and sub-commands. This chapter gives a

description of all valid commands for the 3G Gateway.

4.1.1. Command format

Typing ‘?’ or ‘help’ after a command will result in a usage text (*h of help response) being

displayed. Usage text gives information about the command format, i.e. valid parameters,

sub-commands etc. An example is shown below (the user input is shown in bold).

Xconf Gateway Service 1 ServiceType ?

*h xConfiguration Gateway Service [1..100] ServiceType:

Numbers 1-100 and None/DiD/IVR/Phonebook are parameters of the configuration (Xconf)

command. Parameters

are arguments upon which the command will operate. Required

parameters are denoted by: < >, while optional parameters are denoted by: [ ]. All possible

values for given parameters are separated with slashes ( / ). For some parameters, only their

names are supplied within the brackets. In these cases specific parameter values need to be

substituted for the parameter names. Allowed parameter values, unless obvious, are provided

when the commands are discussed.

Sub-commands

are commands grouped together within a command. Different sub-commands

within a command may have different parameter sets. In the example below: Address and

Authentication are sub-commands to the command H323Gatekeeper. In the same sense

Mode, ID and Password are sub commands of H323Gatekeeper Authentication.

xconf H323Gatekeeper ?

*h xConfiguration H323Gatekeeper Address: <IPAddr>

*h xConfiguration H323Gatekeeper Authentication Mode: <Auto/Off>

*h xConfiguration H323Gatekeeper Authentication ID: <S: 0, 50>

*h xConfiguration H323Gatekeeper Authentication Password: <S: 0, 50>

NOTE! The Data port Command Interface is not case sensitive.

4.1.2. Command types

The commands can be divided into two major classes:

• Parameter Configuration Commands, Xconf.

• Status Commands, Xstat.

TANDBERG GW Data port Command Interface User Guide

• User Commands, Xcom.

Parameter Configuration Commands

are commands that set a system parameter to a specific

value. E.g.: The command Xconf telnet mode: "on" enables telnet access on the gateway. If

the command is syntactically correct the GW returns OK, otherwise the GW returns

ERROR. When the parameter is successfully changed, the GW will return the command with

the new value. An example is shown below (the user input is shown in bold).

Xconf telnet mode: "on"

*c xConfiguration Telnet Mode: On

When issuing a Parameter Setting Command without a parameter, the GW will return the

command with the current setting. E.g.:

Xconf telnet mode

*c xConfiguration Telnet Mode: On

Status Commands

are commands that list different sets of system parameters. Status

commands are automatically called when corresponding parameters are being changed.

4.2. The commands

The commands are divided into five groups: System Configuration Commands, General GW

Commands, System Status Commands, Debug Commands and Special Commands.

TANDBERG GW Data port Command Interface User Guide

4.2.1. System Configuration Commands

Command: Description:

H323Gatekeeper

Sets gatekeeper parameters.

NOTE! H.323 services must be set before the GW can be registered to a

gatekeeper.

H323Gatekeeper Address <IPAddr>

H323Gatekeeper Authentication Mode <Auto/off>

H323Gatekeeper Authentication ID: <S: 0, 50>

H323Gatekeeper Authentication Password: <S: 0, 50>

---

sub-commands:

• Authentication Mode configures the use of authentication

against a gatekeeper.

• Authentication ID Configures the user name used within an

authentication challenge

• Authentication Password sets the password used within the

authentication process.

NOTE! Authentication Password is write only.

Example of H323Gatekeeper feedback:

Xconf H323Gatekeeper Authentication

*c xConfiguration H323Gatekeeper Authentication Mode: Off

*c xConfiguration H323Gatekeeper Authentication ID: ""

H323CallSetup

Configures for direct or via gatekeeper calling

H323CallSetup Mode: <Direct/Gatekeeper>

Example of H323CallSetup feedback:

*c xConfiguration H323CallSetup Mode: Direct

Configures the LAN interfaces when static IP address allocation is used.

NOTE! The GW needs to reboot before the changes will take effect.

IP Assignment: <DHCP/Static>

IP Address <IPAddr>

IP Address Subnetmask <Subnetmask>

IP Address Gateway <IPAddr>

IP Address DNS Server [1..5] Address <IPAddr>

IP Address DNS Domain Name <S: 0, 64>

---

parameters:

TANDBERG GW Data port Command Interface User Guide

• DNS Server: Number identifying one of 5 DNS servers which

can be configured. If this parameter is omitted the command

applies to the first configuration (1).

sub-commands:

• Assignment: Selects between DHCP (Dynamic Host

Configuration Protocol) or static IP address allocation. When

DHCP is selected the GW will automatically receive all the

necessary information from the DHCP server. This function

should be used when the GW is connected to a LAN using

DHCP. When using this mode, IP-address and IP-subnet mask

are not used because the DHCP server supplies these parameters.

• Address: Sets the static IP address for the given LAN interface.

• Subnetmask: Sets the subnet mask variable. Subnet mask

defines the network class. If the setting is 255.255.255.0 the local

network will support up to 256 nodes, denoting a class C

network. If the setting is 255.255.0.0 the local network is a class

B network with 65536 addressable nodes.

• Gateway: Sets the gateway IP address. If a gateway is located on

the LAN and the GW needs to reach nodes through this gateway,

the gateway address can be set using the gateway variable (the IP

address of the gateway will be set automatically if the GW is in

DHCP mode)

• Domain Name: Sets the domain name string of which the

gateway is part of. Minimum 0, maximum 64 characters.

Example of IP Address feedback:

*c xConfiguration IP Address: "127.0.0.1"

Ethernet

Sets LAN port speed.

NOTE! The GW needs to reboot before the changes will apply.

Ethernet <speed>

---

parameters:

• speed: auto/10half/10full/100half/100full. The speed is either

set to auto or manually from 10mb half duplex to 100mb full

duplex. When set to auto the GW will automatically negotiate

with the network and use the best available setting.

Example of Ethernet feedback:

*c xConfiguration Ethernet Speed: Auto

ISDN

Defines various ISDN protocol settings.

ISDN IncomingBearerCapability: <UDI/All>

ISDN OutgoingBearerCapability: <H324m/UDI>

ISDN BRI SwitchType: <NI/ATT/Euro/Japan>

ISDN PRI SwitchType: <NI/ATT/Euro/Japan>

ISDN PRI Interface LowChannel: <1..31>

---

Parameters:

sub-commands:

TANDBERG GW Data port Command Interface User Guide

Within ISDN different bearer capabilities are used to signal the type of date

(Voice, Data, H320, H324M), which is used by switches and other

equipment to determine what to do with the data or the call (compand

neglect etc).

• IncomingBearerCapability: sets the ISDN bearer capability of

the incoming 3G calls. In some situations the non correct UDI

bearer is used in stead of the right H324M capability. This setting

makes it possible to accept incoming 3G calls both situations..

• OutgoingBearerCapability: sets the ISDN bearer capability for

the outgoing 3G calls. In some situations the switch does not

accept calls which use the correct H324M capability. This setting

makes it possible to use the gateway in these situations (UDI).

• BRI SwitchType: Sets the switch type of the gateway in case of a

BRI version.

• PRI SwitchType: Sets the switch type of the gateway in case of a

PRI version.

• PRI Interface LowChannel: This parameter sets the lowest

channel to start with when making outgoing call (to 3G handsets)

Example of ISDN feedback:

*c xConfiguration ISDN IncomingBearerCapability: All

*c xConfiguration ISDN OutgoingBearerCapability: UDI

*c xConfiguration ISDN BRI SwitchType: Euro

*c xConfiguration ISDN PRI SwitchType: Euro

*c xConfiguration ISDN PRI Interface LowChannel: 1

E1 is the configuration of CRC4 for the ISDN PRI lines.

E1 Interface CRC4: <On/Off>

Example of E1 feedback:

*c xConfiguration E1 Interface CRC4: Off

HTTPS

Enables or disables access to HTTPS services.

NOTE! Changes become effective after reboot

HTTPS Mode <On/Off>

Example of HTTPS feedback:

*c xConfiguration HTTPS Mode: Off

HTTP

Enables or disables access to HTTP services.

NOTE! Changes become effective after reboot.

HTTP Mode <On/Off>

Example of HTTP feedback:

*c xConfiguration HTTP Mode: On

SNMP

Configures the SNMPmib.

Note! For more information about SNMP please read the TANDBERG

SNMP application note.

SNMP Mode < On/Off/ReadOnly/TrapsOnly >

SNMP CommunityName: <S: 0, 16>

SNMP SystemContact: <S: 0, 70>

TANDBERG GW Data port Command Interface User Guide

SNMP SystemLocation: <S: 0, 70>

SNMP HostIPAddr [1..3]: <IPAddr>

---

parameters:

• Mode: < On/Off/ReadOnly/TrapsOnly >

• Community Name: Text string of maximum 16 characters.

• System Contact: Text string of maximum 70 characters

• System Location: Text string of maximum 70 characters

• Host IP Addr: The IP addresses of max 3 SNMP trap hosts

sub-commands:

• Mode enables or sets the mode of SNMP support

• Community Name is used to authenticate SNMP requests.

SNMP requests must have this ‘password’ in order to receive a

response from the SNMP agent in the gateway.

• System Contact, Used to identify the system contact via SNMP

tools such as HPOpenView or TANDBERG Management Suite

• System Location Used to identify system location via SNMP

tools such as HPOpenView or TANDBERG Management Suite

• Host IP Addr identifies the IP-address of the SNMP manager.

Up to three different SNMP Trap Hosts can be defined. Your

LAN administrator should provide the correct values for these

fields

Example of SNMP feedback:

*c xConfiguration SNMP Mode: On

*c xConfiguration SNMP CommunityName: "public"

*c xConfiguration SNMP SystemContact: ""

*c xConfiguration SNMP SystemLocation: ""

*c xConfiguration SNMP HostIPAddr 1: "127.0.0.1"

*c xConfiguration SNMP HostIPAddr 2: "127.0.0.1"

*c xConfiguration SNMP HostIPAddr 3: "127.0.0.1"

SSH

Enables or disables SSH interface on the 3G GW

SSH Mode: <On/Off>

---

Example of SSH feedback:

*c xConfiguration SSH Mode: On

TELNET

Enables or disables telnet interface on the 3G GW

Telnet Mode: <On/Off>

---

Example of TELNET feedback:

*c xConfiguration Telnet Mode: On

SystemUnit

Sets the 3G GW name and password

SystemUnit Name: <S: 0, 50>

SystemUnit Password: <S: 0, 16>

---

Parameters:

• Name: Text string of maximum 50 characters

• Password: Text string of maximum 16 characters

TANDBERG GW Data port Command Interface User Guide

sub-commands

• Name, sets the name of the 3G Gateway

• Password, sets the password of the 3G gateway

Example of SystemUnit feedback:

*c xConfiguration SystemUnit Name: ""

TANDBERG GW Data port Command Interface User Guide

4.2.2. General GW Commands

Command: Description:

Gateway

This command is used to configure the 3G gateway dialling rules, like for

example direct inward dialling, H323 call prefixes and dial in numbers. It is

possible to define 100 services, each with the parameters:

• Description indicates the user applied name of the service

• InNetType indicates the dial in for this particular service

configuration.

• OutNetType indicates the dial out for this particular service

configuration

• InPrefix will be used for matching the incoming called

number/address and is used to register with the gatekeeper in case

call type is H323

• InPostfix is the part of the dialed number that will be

removed/replaced.

• ServiceType indicates whether this service is a direct inward dialing,

a phonebook or an IVR service is.

• OutPrefix and OutPostfix will be used to construct the

number/address that will be called (if applicable) using this service.

Service [1..100] Description: <S: 0, 30>

Service [1..100] InNetType: <H324m/3G/H323 >

Service [1..100] OutNetType: <H324m/3G/H323 >

Service [1.. 100] InPrefix: <S: 0, 30>

Service [1.. 100] InPostfix: <S: 0, 30>

Service [1.. 100] ServiceType: < None/DiD/IVR/Phonebook >

Service [1.. 100] OutPrefix: <S: 0, 30>

Service [1.. 100] OutPostfix: <S: 0, 30>

LoadLimit: <0..100>

---

Parameters:

sub-commands:

• Description: This is a friendly name for the service configured like

for example 3G to H323 and 3G hotline to H323

• InNetType.

• OutNetType

• InPrefix.

• InPostfix

• ServiceType

• OutPrefix

• OutPostfix

• LoadLimit The GW will signal busy to the gatekeeper when the

current load on the GW reaches this limit. The current system load

can be monitored by the status command SystemLoad

TANDBERG GW Data port Command Interface User Guide

Example of Gateway feedback:

*c xConfiguration Gateway Service 1 Description: ""

*c xConfiguration Gateway Service 1 ServiceType: DiD

*c xConfiguration Gateway Service 1 InNetType: H324m/3G

*c xConfiguration Gateway Service 1 InPrefix: 6789""

*c xConfiguration Gateway Service 1 InPostfix: ""

*c xConfiguration Gateway Service 1 OutNetType: H324m/3G

*c xConfiguration Gateway Service 1 OutPrefix: "5"

*c xConfiguration Gateway Service 1 OutPostfix: ""

*c xConfiguration Gateway LoadLimit: 100

When dialling the number 67890000 there will be a match with “0000” as the

significant number. The H.323 number to call is: 50000 (construction: prefix +

significant numbers + postfix). When dialling number 67894321 this will

match with “4321” as the significant number. The H.323 number to call is:

54321 (construction: prefix + significant numbers + postfix)

ExternalManager

This command sets the path and address of TMS server.

ExternalManager Path: <S: 0, 255>

ExternalManager Address: <IPAddr>

sub-commands:

• Path

• Address, the IP address of the manager

Example of ExternalManager feedback

*c xConfiguration ExternalManager Path:

"tms/public/external/management/SystemManagementService.asmx"

*c xConfiguration ExternalManager Address: ""

CorporateDirectory

This command sets the path and address of the Corporate Directory

(phonebook) server.

CorporateDirectory Address: <IP Addr>

CorporateDirectory Path: <S: 0, 255>

sub-commands:

• Path, the path of the HTTP request

• Address, the IP address of the manager

Example of Corporate Directory feedback

*c xConfiguration CorporateDirectory Path:

"tms/public/external/phonebook/PhoneBookService.asmx"

*c xConfiguration CorporateDirectory Address: ""

NTP

This command sets the address of the NTP server.

NTP Address: <IP Addr>

sub-commands:

• Address, the IP address of the server

Example of NTP feedback

*c xConfiguration NTP Address: "131.188.3.220"

Options

View and adapt option keys

TANDBERG GW Data port Command Interface User Guide

NOTE! The GW needs to reboot before the changes will take effect.

Options [1 .. 64] Key: <S: 0, 90>

---

sub-commands:

• Key: Option key for e.g. BRI, PRI or SS7 trunks.

Example of Options feedback:

*c xConfiguration Options 1 Key: "115201SS7-1-55C3EBB7"

*c xConfiguration Options 2 Key: "115201P1-1-6A96DAA4"

*c xConfiguration Options 3 Key: "115201P1-2-1811D4FA"

*c xConfiguration Options 4 Key: "115201P1-3-79828C53"

*c xConfiguration Options 5 Key: "115201P1-4-B5E5BD4A"

SIP

Configures the SIP Proxy Mode and Address settings.

Mode <On/Off>

Proxy Address <IPAddr>

Proxy Port: <1 .. 65534>

---

sub-commands:

• Mode: If Mode = On the 3G Gateway is registered with the Proxy

server

• Address: IP address of the Proxy server the 3G Gateway is to be

registered to.

• Port: Port number of the Proxy server.

Example of SIP feedback:

*c xConfiguration SIP Proxy Mode: Off

*c xConfiguration SIP Proxy Address: "127.0.0.1"

*c xConfiguration SIP Proxy Port: 5060

SS7

Configures the SS7 Signalling for all 3G Gateway trunks

NOTE! The GW needs to reboot before the changes will take effect.

OPC: <0 .. 16383>

NetworkIndicator: <International0/International1/National0/National1>

Law: <ALaw/ULaw>

LinkSet [1 .. 2] Mode: <On/Off>

LinkSet [1 .. 2] DPC: <0 .. 16383>

LinkSet [1 .. 2] Link [1 .. 2] Mode: <On/Off>

LinkSet [1 .. 2] Link [1 .. 2] Trunk: <1 .. 4>

TANDBERG GW Data port Command Interface User Guide

LinkSet [1 .. 2] Link [1 .. 2] Timeslot: <1 .. 31>

LinkSet [1 .. 2] Link [1 .. 2] SLC: <0 .. 15>

Trunk [1 .. 4] Mode: <On/Off>

Trunk [1 .. 4] DPC: <0 .. 16383>

Trunk [1 .. 4] CircuitIdentificationCode: <0 .. 16383>

Route [1 .. 8] DPC: <0 .. 16383>

Route [1 .. 8] Priority: <1 .. 4>

Route [1 .. 8] LinkSet: <Off/1/2>

---

sub-commands:

• OPC: A number between 0-2

, which uniquely identifies a signaling

point, in this case the 3G Gateway, within a telephone network. This

number consists of three parts, i.e. a network, cluster and member

number, and will be provided by the network operator.

• NetworkIndicator:,A two bit data field within the Service

Information Octet of the Message Signal Unit that permits

discrimination between national and international messages.

• Law: audio standard: Either ALAW or ULAW. An a-law algorithm

is a standard companding, i.e. compressing and expanding, algorithm,

used in European digital communication systems to optimize, i.e.

modify, the dynamic range of an analog signal for digitizing. The µ-

law algorithm is similar to a-law and used in North American and

Japanese systems.

• LinkSet Mode: Enable or disable linksets.

• LinkSet DPC: Uniquely identifies the destination signaling point of

the link. This can differ from the DPC of the trunk, e.g. the DPC of a

Signaling Transfer Point (STP), see example 2 below.

• LinkSet Link Mode: Enable a link in a link set.

• LinkSet Link Trunk: Number of the trunk (1 - 4) in which a time

slot is reserved for signaling.

• LinkSet Link Timeslot: Number of the time slot, within

aforementioned trunk, reserved for signaling.

• LinkSet Link SLC: A Signaling Link Code is a unique link number

provided by the network operator to identify a link.

• Trunk Mode: Enable or disable a trunk.

• Trunk DPC: Uniquely identifies the destination signaling point of

the trunk. It will be provided by the network operator.

• Trunk CircuitIdentificationCode: The Circuit Identification Code

is a unique identifier for a data time slot in a cable (trunk). In this

case the CIC acts as base address and can be defined for each SS7

trunk and sets the first time-slot number of the respective SS7 trunk.

• Route DPC: Unique identifier indicating the destination signaling

point of a trunk.

• Route Priority: Priority level of the route to the destination signaling

point. Fail-over signaling paths will be followed according to this

priority.

• Route LinkSet: Indicates the link to the destination signaling point

according to the above mentioned priority setting.

For more details on the sub-commands please read the chapter about SS7

TANDBERG GW Data port Command Interface User Guide

in the 3G Gateway User Manual.

Example of SS7 feedback:

*c xConfiguration SS7 OPC: 0

*c xConfiguration SS7 NetworkIndicator: National0

*c xConfiguration SS7 Law: ALaw

*c xConfiguration SS7 LinkSet 1 Mode: Off

*c xConfiguration SS7 LinkSet 1 DPC: 0

*c xConfiguration SS7 LinkSet 1 Link 1 Mode: Off

*c xConfiguration SS7 LinkSet 1 Link 1 Trunk: 0

*c xConfiguration SS7 LinkSet 1 Link 1 Timeslot: 0

*c xConfiguration SS7 LinkSet 1 Link 1 SLC: 0

*c xConfiguration SS7 LinkSet 1 Link 2 Mode: Off

*c xConfiguration SS7 LinkSet 1 Link 2 Trunk: 0

*c xConfiguration SS7 LinkSet 1 Link 2 Timeslot: 0

*c xConfiguration SS7 LinkSet 1 Link 2 SLC: 0

*c xConfiguration SS7 LinkSet 2 Mode: Off

*c xConfiguration SS7 LinkSet 2 DPC: 0

*c xConfiguration SS7 LinkSet 2 Link 1 Mode: Off

*c xConfiguration SS7 LinkSet 2 Link 1 Trunk: 0

*c xConfiguration SS7 LinkSet 2 Link 1 Timeslot: 0

*c xConfiguration SS7 LinkSet 2 Link 1 SLC: 0

*c xConfiguration SS7 LinkSet 2 Link 2 Mode: Off

*c xConfiguration SS7 LinkSet 2 Link 2 Trunk: 0

*c xConfiguration SS7 LinkSet 2 Link 2 Timeslot: 0

*c xConfiguration SS7 LinkSet 2 Link 2 SLC: 0

*c xConfiguration SS7 Trunk 1 Mode: Off

*c xConfiguration SS7 Trunk 1 DPC: 0

*c xConfiguration SS7 Trunk 1 CircuitIdentificationCode: 0

*c xConfiguration SS7 Trunk 2 Mode: Off

*c xConfiguration SS7 Trunk 2 DPC: 0

*c xConfiguration SS7 Trunk 2 CircuitIdentificationCode: 0

TANDBERG GW Data port Command Interface User Guide

*c xConfiguration SS7 Trunk 3 Mode: Off

*c xConfiguration SS7 Trunk 3 DPC: 0

*c xConfiguration SS7 Trunk 3 CircuitIdentificationCode: 0

*c xConfiguration SS7 Trunk 4 Mode: Off

*c xConfiguration SS7 Trunk 4 DPC: 0

*c xConfiguration SS7 Trunk 4 CircuitIdentificationCode: 0

*c xConfiguration SS7 Route 1 DPC: 0

*c xConfiguration SS7 Route 1 Priority: 0

*c xConfiguration SS7 Route 1 LinkSet: Off

*c xConfiguration SS7 Route 2 DPC: 0

*c xConfiguration SS7 Route 2 Priority: 0

*c xConfiguration SS7 Route 2 LinkSet: Off

*c xConfiguration SS7 Route 3 DPC: 0

*c xConfiguration SS7 Route 3 Priority: 0

*c xConfiguration SS7 Route 3 LinkSet: Off

*c xConfiguration SS7 Route 4 DPC: 0

*c xConfiguration SS7 Route 4 Priority: 0

*c xConfiguration SS7 Route 4 LinkSet: Off

*c xConfiguration SS7 Route 5 DPC: 0

*c xConfiguration SS7 Route 5 Priority: 0

*c xConfiguration SS7 Route 5 LinkSet: Off

*c xConfiguration SS7 Route 6 DPC: 0

*c xConfiguration SS7 Route 6 Priority: 0

*c xConfiguration SS7 Route 6 LinkSet: Off

*c xConfiguration SS7 Route 7 DPC: 0

*c xConfiguration SS7 Route 7 Priority: 0

*c xConfiguration SS7 Route 7 LinkSet: Off

*c xConfiguration SS7 Route 8 DPC: 0

*c xConfiguration SS7 Route 8 Priority: 0

*c xConfiguration SS7 Route 8 LinkSet: Off

TANDBERG GW Data port Command Interface User Guide

VideoPortal

Registers the 3G Gateway with the VideoPortal

NOTE! The GW needs to reboot before the changes will take effect.

Mode <On/Off>

System [1 .. 2] IP Address <IPAddr>

---

sub-commands:

• Mode: If Mode = On the 3G Gateway is registered with 1 or 2 video

portals

• Address: IP address of the Video Portal the 3G Gateway is to be

registered to.

Example of VideoPortal feedback:

*c xConfiguration VideoPortal Mode: On

*c xConfiguration VideoPortal System 1 Address: "10.31.1.8"

*c xConfiguration VideoPortal System 2 Address: "127.0.0.1"

Page is loading ...

TANDBERG D1320202 User manual

Brand: TANDBERG

Model: D1320202

Type: User manual

This manual is also suitable for

Network Router D1320202

TANDBERG Network Router D1320202

Download PDF

report

TANDBERG D1320202 User manual

This manual is also suitable for

TANDBERG D1320202 User manual

Related papers

Other documents