Dormakaba 10-3-FPD Installation guide

Brand: Dormakaba

Model: 10-3-FPD

Category: Fire protection

Type: Installation guide

This manual is also suitable for

PDD-FT-3

Fire Panel Interface

With EOL Trigger

Installation and Specifications Manual

PDD-FT-3

InstallatIon

ISPSFPD-3

PCN16045

R12/17GR

www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: [email protected]

Details

The PDD-FT-3 board is a fire panel control interface. This board can be used to control DC

output based on a fire alarm control panel. Two outputs switch state on alarm.

Features

• NonLatchingorLatchingmode

• Universal12VDCor24VDCOperation

• Reversepolarityprotected

• NormallyON&NormallyOFFOutput

• OutputLED’sindicatecondition

• OutputscanbeTriggeredwith:

  1)N/OorN/CSwitchwithSupervisedEndofLineResistor(EOL)

  2)N/CSwitchwith(OVR)override

  3)N/CSwitchwith(AUX-IN)auxiliary

  4)Groundonanytriggerinputwhen(GRN)Jumperisenabled

• FormCDPDTRelayIndicatesTriggerStatus

• 3AmpTransferRelayContacts

• Autoormanualresetbyjumperselection

Installation Instructions

1. MountthePDD-FT-3boardinasuitablelocationincloseproximitytothepowersupply.

Note:

a) Groundfaultdetectionwillonlyworkifconductivestandoffsareusedandpower

  supplyenclosureisproperlygrounded.

b) Asthisdevicecanbeusedtopowermultipledevicesensurethatallwiringisofan

  appropriategaugeforthedevicesbeinginstalled.

 c) ThisRCIboardisforuseinacontrolledindoorenvironment.ThePDD-FT-3and

  alldevicesconnectedtoorpoweredthroughthePDD-FT-3shallbeinstalledwithin

  thesamecontinuousbuildingstructure.Installationmustbeinaccordancewith

  localbuildingandfirecodes.CheckwithAuthorityHavingJurisdiction(AHJ)for

  detailspriortoinstalling.

 d) Allpowerlimitedwiringmustbeaminimumof.25”fromnon-powerlimitedwiring.

 e) Maximumtorqueof7in*lbforblackinputandoutputterminals.

2.Connect“INPUT”terminalstooutputofDCsupply,payingcloseattentiontopolarityof

 DCoutputfrompowersupply.

3.ConnectdevicestobepoweredtooutputterminalsofPDD-FT-3controlboard,paying

 closeattentiontopolarityrequirements.Minimum22AWGandmaximumdistanceof 

 6170ft.forfieldwiring.

4.Setjumpers(RST,OVR,AUX,andGRN)asrequiredforproperinstallation.

5. ConnectfirealarmcontrolpaneltoEOLinputterminals,ensurethe2.2Kresistoris

installed at the terminals in the fire alarm panel.

 a) Seefirealarmcontrolpanelinstallationandoperationmanualfordetailsabout

  signalingrequirements.

 b) Fig’s2-6inthisinstallationguidewillprovidedetailsonwiringtothefirealarm

control panel.

6. Connectanyrequiredmonitoringequipmenttothetriggerrelaysusing

 appropriatecabling.

7. Thisunitistobepoweredfroma10SeriesRCIPowerSupplyoraULlisted 

 powersupply.

8. Applypowertopowersupplytoactivatecontrolboardandtestallconnecteddevices.

Specifications

• ForULlistedpowersupply

• UL2946eandULCS319Class1AccessControlSystemUnit

 AccessControlLevels:

Endurance:Level4LineSecurity:Level1

 PowerStandby:Level1DestructiveAttack:Level1

Input

• InputVoltage:12or24VDC±10%

• TypicalCurrentDrawwithnoOutputLoad:10mA@12VDC

  15mA @24VDC

Output

• OutputRelayRating:3A

Monitor Inputs

• EOL(EndofLine)Trigger:Triggerat+or–50%of2.2K

• OVRTrigger

• AUXTrigger

• ResetInput

• GroundFaultTrigger(seenote1a)

Monitor Outputs

• TriggerRelayRating:1ADPDT

Environmental

• Useinacontrolledindoorenvironment

Warning:Improperwiringconnectionsmayresultindamagetothisproduct.

Miseengarde:Unmauvaisraccordementdescâblesrisqued’endommagerceproduit.

Description of PDD-FT-3 Connections SeeFig.1

Input Power

“-INPUT+”:2positionterminalblockwithselfclampingscrewswillacceptmultiple12AWG

wiresUniversalinput.

Output Power

Two,2positionterminalblocks.Selfclampingscrewswillacceptmultiple12AWGwires.

“-N/ON+”arenormallyONoutputpower.ThisoutputisONwhenthePDD-FT-3isnottrig-

gered.“-N/OFF+”isnormallyOFF.ThisoutputisONwhenthisunitistriggered.Thetrans-

ferrelayisratedat3Amps.

Power LED’s

Aredledaboveeachoutputindicateswhichoutputisactive.

Input Trigger EOL*

2positionterminalblock–Willaccept12AWGwire.Thisinputmustseethe2.2Kohmend

oflineresistortobeinthenormalsetcondition.Achangeinresistanceof±50%willcause

thetriggerrelaystodropoutintheTriggeredmode.Thischangeinresistanceiscausedby

thesupervisedwirebetweentheEOLatthefirepanelandthePDD-FT-3beingshortedor

opened.TheEOLsupervisesthepairofwires.

Input Trigger OVR*

2positionterminalblock-Willaccept12AWGwire.Thispairisnormallyclosedandcanbe

connectedtoanoverrideswitch.WhenOVRisopen,unitwilltrigger.

Input Trigger AUX-IN*

2positionterminalblock-Willaccept12AWGwire.Thispairisnormallyclosedandcanbe

connectedtoanauxiliarydevice.WhenAUX-INisopen,unitwilltrigger.

Reset 2 Position Terminal Block*

2positionterminalblock-Willaccept12AWGwire.Whenthispairisshorted,inputtrig-

gersdonotlatch.Ifpairisopen,theinputtriggerswilllatchuntilalarmiscorrectedand

RESETismomentaryclosedtoresettrigger.

*Minimum22AWGandmaximumdistanceof6170ftforfieldwiring.

Jumpers RST - OVR - AUX

Jumpersareusedtoactivate(remote)featuresasrequired.

Jumpers GRN

Thisjumperisusedtoenablegroundsupervisionortheinputs.Ifthejumperisconnected

tobothheaders,andthemountingholeadjacenttojumperisconnectedtoearthground,a

groundonanyoftheinputtriggerswillcauseatrigger.

Trigger Status Terminal block

Two,3positionterminalblocks-Willaccept12AWGwire.FormCDPDTrelaywitha1

Ampratingwillindicatetheconditionoftrigger.CandNOarenormallyopeninthenormal

energizenottriggeredstate.CandNCarenormallyclosedinthenormalenergizednottrig-

geredstate.ThesecontactsmaybeusedtoprovidefeedbacktotheFACPorotherauxilary

devices.

Fig.2-FirePanelConnectionsforNon-Latching

AutomaticResetOperation

ThisapplicationillustrateshowtoconnectthePDD-FT-3toapowersupplyformaininput

aswellasafirealarmcontrolpanel.Ifwiredinthismanner,outputswillchangestateonly

aslongasthefirealarmrelayisactive.WhenthefirealarmresetsthePDD-FT-3outputs

will also reset.

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

2.2 K

PDD-FT

CNO NC

TRIGGERED

DC Input

Trigger Output

Ground Fault Jumper

Reset Input

End Of Line

Override Input

Auxilary Input

Normally "On" Output

Normally "Off" Output

Output Led's

-BAT+

- Output +24V 12V

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

PDD-FT

CNO NC

TRIGGERED

OUTPUT

FIRE PANEL

BY OTHERS

CNC NO

2.2 K

OUTPUT

2.2 K

C NO

Fig.1-PDD-FT-3Connections

Application Diagrams

Fig.3-FirePanelConnectionsforLatchingReleasewithN/OManual

Reset

ThisapplicationillustrateshowtoconnectthePDD-FT-3toapowersupplyformaininput

aswellasafirealarmcontrolpanel.Ifwiredinthismanner,outputswillchangestate

wheneverthefirealarmrelayactivatesandremainlatchedinthetriggeredstateuntilreset

byactivatingtheN/Oswitch.

Note:RemoveRSTjumperformanualresetoperation.

Remarque:RetirezlabretelleRSTpoureffectueruneréinitialisation manuelle.

Fig.4-ConnectionsforNon-Latchingreleaseresetusingmultiple

PDD-FT-3 boards

ThisapplicationillustrateshowtoconnectthePDD-FT-3toapowersupplyformaininput

aswellasafirealarmcontrolpanel.Ifwiredinthismanner,outputswillchangestateonly

aslongasthefirealarmrelayisactive.WhenthefirealarmresetsthePDD-FT-3outputs

willalsoreset.ConnectingtheEOLinputofoneboardtothetriggerrelayofthenextboard

asshownwillallowforoverrideandresetofmultipleboards.

Note:TheRSTjumpermustbeleftinplaceonallboardsforautomaticresetoperation.

Remarque:LabretelleRSTdoitêtre laisséeenplacesurtouslespanneauxpoureffectuer

une réinitialisationautomatique.

-BAT+

- Output +24V 12V

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

PDD-FT

CNO NC

TRIGGERED

OUTPUT

FIRE PANEL

BY OTHERS

CNC NO

2.2 K

OUTPUT

2.2 K

C NO

-BAT+

- Output +24V 12V

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

PDD-FT

CNO NC

TRIGGERED

OUTPUT

FIRE PANEL

BY OTHERS

CNC NO

2.2 K

OUTPUT

2.2 K

C NO

-BAT+

- Output +24V 12V

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

PDD-FT

CNO NC

TRIGGERED

2.2 K

Fig.5-ConnectionsforlatchingreleasewithN/Omanualresetusing

multiplePDD-FT-3boards(Master&Slave)

ThisapplicationillustrateshowtoconnectthePDD-FT-3toapowersupplyformaininput

aswellasafirealarmcontrolpanel.Ifwiredinthismanner,outputswillchangestate

wheneverthefirealarmrelayactivatesandremainlatchedinthetriggeredstateuntil

MasterisresetbyactivatingtheN/Oswitch.ConnectingtheEOLinputofoneboardtothe

triggerrelayofthenextboardasshownwillallowforresetofmultipleboards.

Note:TheRSTjumpermustbeleftinplaceonallslaveboardsexcepttheonethatis

directlyconnectedtothefirealarm(Master),reset,andswitches.

Remarque: LabretelleRSTdoitêtre laisséeenplacesurtouslespanneauxasservis,sauf

celuiquisetdirectementconnecté àl’alarmedefeu(d’exploitation),situé près des boutons

de réinitialisationetd’annulation.

Fig.6-Fire Panel

Connectionsfor

Latching Trigger

withN/OManual

ResetandN/Cover-

ridewithBattery

Backup

This application illus-

trates how to connect

thePDD-FT-3toanRCI

PowerSupplyformain

input,ACfailureaswell

as a fire alarm control

panel.Ifwiredinthis

manner,triggeroutputs

willchangestatewhen-

everthefirealarm,or

ACfailurerelaysactivate.ThePDD-FT-3outputswillremaininthetriggeredstateuntilboth

relayshavebeenresetandtheN/Omanualresetistriggered.

Note: EnsurejumpersforRST,OVR,andAUXINareremovedtoallowterminalstooperate

correctly.

Remarque:Assurez-vousquelesbretellesRST,OVRetAUXINsontretirées afin de per-

mettreauxterminauxdefonctionnercorrectement.

-BAT+

- Output +24V 12V

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

PDD-FT

CNO NC

TRIGGERED

OUTPUT

FIRE PANEL

BY OTHERS

CNC NO

2.2 K

OUTPUT

2.2 K

C NO

-BAT+

- Output +24V 12V

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

PDD-FT

CNO NC

TRIGGERED

2.2 K

-BAT+

- Output +

GRN

24V 12V

NO C NC

AC Fail

- N/OFF +- N/ON +

- INPUT +

GRN

EOL

RESET

AUX

OVR

RST

AUX - IN

OVR

CNO NC

TRIGGERED

PDD-FT

CNO NC

TRIGGERED

OUTPUT

FIRE PANEL

BY OTHERS

CNC NO

2.2 K

OUTPUT

2.2 K

C NO

2.2 K

POWER SUPPLY

INTER-CONNECT.

N/O MANUAL RESET

SEE NOTE 4.

EOL

RESET

RST

BATTERY

-BAT+

N/C MANUAL OVER-RIDE

SEE NOTE 3.

AC FAIL CIRCUIT

ONLY REQUIRED WITH

BATTERY BACKUP.

SEE NOTE 5.

Non-power limited

Power limited

3) FOR MANUAL OVER-RIDE REMOVE JUMPER "OVR"

4) FOR MANUAL RESET REMOVE JUMPER "RST"

5) FOR AUX-IN REMOVE JUMPER "AUX"

6) JUMPER GRN IS FOR GROUND FAULT DETECTION

ON ENABLES GROUND FAULT, REMOVED DISABLES

GROUND FAULT.

AND INSTALL N/C SWITCH.

AND INSTALL A N/O SWITCH.

AND INSTALL A N/C CIRCUIT.

1) DISCONNECT AC INPUT PRIOR TO SERVICING.

SPACING OF .25" FROM NON-POWER LIMITED CIRCUITS.

2) ALL POWER LIMITED CIRCUITS TO HAVE A MINIMUM

NOTES 3-6 REFER TO PDD-FT ONLY

NOTE:

GROUND FAULT JUMPER

SEE NOTE 6.

Notes

For Technical Support:

1.800.265.6630|WWW.RUTHERFORDCONTROLS.COM

PDD-FT-3TroubleshootingGuide

Problem  Solution

-CheckACPower.

-CheckPowerSupplyforvoltageoutput.

-Checkdevicesconnectedtooutputsfor

 ashortcircuit.(PTC’smayrequireshort

 toberemovedforseveralminutes 

 beforeautomaticallyresetting).

-Checktriggerjumpers.OutputLED 

 shouldbelitifoutputisactive.

-Checkforproperwiringconnectionson

 triggerconnections.

-Ensurethat2.2Kresistorisinstalledat

 EndofLinepositioninthewiring.

-Checkdevicesconnectedtooutputsfor

 ashortcircuit.(PTC’smayrequire 

 shorttoberemovedforseveralminutes

 beforeautomaticallyresetting.)

NoDCoutputfromterminals.

Triggerisactiveandwillnotreset.

Troubleoutputrelayisde-energized.

(Relayterminalsarelabeledshownin

theNormal,energized,“notrouble”

condition.Relaysareenergizedwhen

notroubleisdetected.)

Dormakaba 10-3-FPD Installation guide

Brand: Dormakaba

Model: 10-3-FPD

Category: Fire protection

Type: Installation guide

This manual is also suitable for

Download PDF

report

Dormakaba 10-3-FPD Installation guide

This manual is also suitable for

Dormakaba 10-3-FPD Installation guide

Related papers

Other documents