Lightolier IS:E610 User manual

Brand: Lightolier

Model: IS:E610

Type: User manual

Lightolier IS:E610 is a pre-wired calculite frame-in-kits fixture intended to provide illumination in various indoor settings. The fixture is designed for easy installation and can be either frame-in, close-in, snap-in, or push-in mounted, depending on the desired application. It features an adjustable mounting bracket that allows for precise placement within the ceiling, ensuring a flush or slightly recessed fit. The fixture accommodates a variety of reflector trims, allowing users to customize the lighting to suit their specific needs and preferences.

Lightolier IS:E610 is a pre-wired calculite frame-in-kits fixture intended to provide illumination in various indoor settings. The fixture is designed for easy installation and can be either frame-in, close-in, snap-in, or push-in mounted, depending on the desired application. It features an adjustable mounting bracket that allows for precise placement within the ceiling, ensuring a flush or slightly recessed fit. The fixture accommodates a variety of reflector trims, allowing users to customize the lighting to suit their specific needs and preferences.

INSTRUCTION SHEET NO.

INSTALLATION OF PRE-WIRED CALCULITE FRAME-IN-KllS

INSTRUCTION SHE~ FOR ITEMS

G41O, E61O, F71O

IS:E610

R0291

Page 1 of

2

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE.

This fixture is intended for installation in accordance with the National Electrical Code and local regulations.

To assure full compliance with local codes and regulations, check with your local electrical inspector before installation. To prevent

electrical shock, turn off electricity at fuse box before proceeding.

Retain these Instructions for maintenance referencw

R

..

‘a-.”-:

RETAINING

SPRING

SECTION

,l#G T ti:EmoR

HOUSING

A. FRAME-IN

B. CLOSE.IN C. SNAP-IN

b. PUSH-IN

FIG. 1 FIG. 2 FIG. 3

FIG. 4

WARNING+RISK OF FIRE)DO NOTINSTALLinSUlatiOn WITHIN3 INCHESOF FIXTURESIDESOR

WIRING COMPARTMENT, NOR ABOVE FIXTURE IN SUCH A MANNER SO AS TO ENTRAP HEAT.

A. FRAME-IN AND WIRE-IN (FIG. 1)

1,Install FRAME-IN SECTION using ADJUSTABLE MOUNTING BRACKET (see below). Wire to supply leads. White fixture lead

to neutral supply lead. Black fixture lead to hot (120V.) supply lead. Bare fixture wire to supply ground. Use wirenuts (local

hardware items). Place all electrical connections in the J-BOX. Attach J-BOX COVER onto J-BOX.

s

2. Adjust MOUNTING FRAME,

o

- MOUNTING

@

– MOUNTING

a. For Flangeless Trim FRAME b. For Overlapping Trim

FRAME

Plaster Ceiling.

[-3

FIG. 9 :? ;

Plaster or Dry Ceiling.

FIG. 8

.J

31,” Max

T

Set MOUNTING FRAME so the

Set MOUNTING FRAME so the bottom edge

bottom edge is flush with finished ceiling, as shown.

is flush with, no higher than %“ above finished ceiling, as shown.

1-1<31-170 1-11= I?” ;V:::::L,N::EV::, E:A:Y:;

“—-—

NOTE 1. To insure proper Installation, the MOUNTING FRAME must always be secure to structural

ceiling members.

...

2. To insure propar Installation, the MOUNTING FRAME must always be secure to structural

ceiling members

B. CLOSE-IN (FIG. 2). C. SNAP-IN (FIG. 3)

}

SEE SEPARATE

Close in ceiling required.

REFLECTOR TRIM

D. PUSH-IN (FIG. 4)

INSTRUCTION

SHEETS

U.S. Pat. No. 4,039,822

-.

1
2

Lightolier IS:E610 User manual

Brand: Lightolier

Model: IS:E610

Type: User manual

Lightolier IS:E610 is a pre-wired calculite frame-in-kits fixture intended to provide illumination in various indoor settings. The fixture is designed for easy installation and can be either frame-in, close-in, snap-in, or push-in mounted, depending on the desired application. It features an adjustable mounting bracket that allows for precise placement within the ceiling, ensuring a flush or slightly recessed fit. The fixture accommodates a variety of reflector trims, allowing users to customize the lighting to suit their specific needs and preferences.

Download PDF

Related papers

Other documents