Home Styles 5099-95 Assembly Instructions

Brand: Home Styles

Model: 5099-95

Type: Assembly Instructions

88509995 C

Kitchen Center

PART LIST

Casual Attire For Today's Home

Dear Our Valuable Customers,

Please follow our assembly instructions in every step,

we guarantee that you will get the perfect merchandise.

Thank you so much for purchasing our quality products.

Thai Patent Pending Numbers 086878

Tools Required For Assembly : Philips screwdriver

Top

1 pc.

Shelf

2 pcs.

Middle Frame

1 pc.

Side Panel

1 pc.

Back Panel

3 pcs.

Side Panel

1 pc.

Front Rail

1 pc.

Door

1 pc.

Door

1 pc.

Drawer

2 pcs.

Side Rack

1 pc.

Side Rack

1 pc.

Brush Chrome Pipes

3 pcs.

Handle Arm

2 pcs.

Base Rack

1 pc.

(Knock-Down Construction, please refer

to the last page of these instructions for

steps to complete assembling drawers)

Base

1 pc.

Middle Frame

1 pc.

Lower Back Stretcher

1 pc.

Upper Back Stretcher

1 pc.

Back Support

2 pcs.

Divider

1 pc.

Round Arm

1 pc.

Shelf

2 pcs.

Drawer

2 pcs.

Caster

with and

without lock

4 pcs.

Head Cap Bolt

30 pcs. (+1Extra)

Hex Wrench

1 pc.

Machine Screw

for Pull Handle

6 pcs.

Adjustable Pin

16 pcs. (+1 Extra)

Wood Plug

7 pcs. (+2 Extra)

Pull Handle

2 pcs.

Pull Handle

2 pcs.

Wood Screw

for Bottom Drawer Part

(Short 6 x ½”)

12 pcs.(+1 Extra)

Wood Screw

for Side Drawer Part

(Long 6 x 1” )

16 pcs.(+1 Extra)

Wood Screw

16 pcs. (+ 1 Extra)

HARDWARE LIST

J1.

Back Post

1 pc.

J2.

Back Post

1 pc.

Assembly Instructions 2/5

STEP 1

IMPORTANT NOTE

Do not tighten up all the screws until each part is properly assembled.

You should keep Hex Wrench in the safe place as you may need to

tighten up the Head Cap Bolts in the future.

STEP 2

Turn the unit in Step1 upside down.

Attach the Middle Frame (D) and (E)

to the unit.

Head Cap Bolt

Attach the Lower

Back Stretcher (H)

to the Side Frame (B),

using Head Cap Bolts.

Attach The Back Post (J1),(J2)

to the Lower Back Stretcher (H)

and slide the Back Panels (F) to place.

Attach the Upper Back Stretcher (G) to the assembled unit, using Head Cap Bolts.

Attach the Front Rail (I) to the Side Frame (B) with Head Cap Bolts.

Attach the Side Frame (C) to the assembled unit, tighten up all Head Cap Bolts.

Head Cap Bolt

Assembly Instructions 3/5

STEP 3

STEP 4

STEP 5

Turn the assembled unit to back its

normal position.

Attach the Divider (Q) in the middle.

Attach the Back Support (R) to the

Upper Back Stretcher (G), using Head

Cap Bolts.

Attach the Handle Arm (W) to the

Side Panel (C) with Head Cap Bolts.

Slide the Round Arm (X) into place.

Place the Base (K) on the unit.

Tighten up all Head Cap Bolts.

Attach 4 Casters to the underside of

the Base (K), put the 2 Casters with

lock in front as you first need to keep

the cart firmly in place. (See sticker in

the bottom indicating front side)

Wood Screw

Locking Caster

Head Cap Bolt

Assembly

Instructions

4/5

STEP 6

STEP 7

Place the Top (A) on the unit.

Tighten up the Head Cap Bolts.

STEP 8

STEP 9

Insert the Adjustable Pins into the Side Panels

and into the Middle Frame at the desired level,

then put the Shelf (N) into the place.

Attach the Pull Handles to the Door (L)

and (M) with Machine Screws.

Attach the Door (L) and (M) to the

Side Panel by sliding the door lift hinges

into the side panel lift hinges.

See assembly instructions for Drawers in

the last page.

Slide the Drawers (P) into place.

Cover all holes with Wood Plugs.

Lift hinge

Assembly

Pull Handle

Assembly

Adjustable Pin

Attach the Side Rack (S) to the Side

Panel (B) with Head Cap Bolts.

Attach the Brush Chrome Pipes(V) and

the Base Rack (U) to the pre-drilled holes

of the Side Rack (S).

Attach the Side Rack (T) to the Side Panel (B).

Head Cap Bolt

(Fig)1

MAKE SURE ROLLER

IS ON THE BACK

Assembly Instructions 5/5

Drawer

Unit Part List

P1.

Front Part

2 pcs.

P3.

Side Part

2 pcs.

P4.

Side Part

2 pcs.

P2.

Back Part

2 pcs.

(Fig) 4

(Fig)2

(Fig) 2

Turn the assembled drawer over and slide the

Plywood Bottom Part (O5) into the grooves

on Side Parts (O3) and (O4). Be sure to push

the plywood all the way forward so it meets the

Front Part (O1).

(Fig) 3

Insert the remaining (6) 1/2” screws

into the pre-drilled holes in Bottom Part

(O5), then tighten all screws

* If you are missing any of these

parts, please contact our DMI

Customer Service Department

at 1-877-831-0319 or fax us at

1-800-755-2878.

(Fig) 1

Line up Side Parts (O3) and (O4) to the Front

Part (O1) and Back Part (O2). Be sure to

follow the Arrow sign sticker on the parts.

Using a Philips screw driver, insert 1” screws

into each of the 4 pre-drilled holes in sides

(O3) and (O4), then tighten half way.

P5.

Bottom Part

2 pcs.

(Fig)3

(Fig)4

Assemble the Pull Handles

with Machine Screws on

the Front Part (O1).

Home Styles 5099-95 Assembly Instructions

Home Styles 5099-95 Assembly Instructions

Home Styles 5099-95 Assembly Instructions

Related papers

Other documents