88 5089 95C
Solid Wood Top Kitchen Cart
with Wood Breakfast Bar
PART LIST
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
HARDWARE LIST
Hex Wrench
1 pc.
Pull Handle
2 pcs.
Machine Screw
for Pull Handle
4 pcs.
Wood Screw
for Caster and
Gate Leg
22 pcs. (+2 extra)
Wood Plug
10 pcs.
(+2 extra)
B.
Side Panel
1 pc.
A.
Top
1 pc.
C.
Side Panel
1 pc.
F.
Back Panel
3 pcs.
G.
Back Piece
2 pcs.
H2.
Front Piece
1 pc.
H1.
Front Piece
1 pc.
I.
Back Stretcher
1 pc.
J.
Front Stretcher
1 pc.
K.
Front Rail
3 pcs.
L.
Base
1 pc.
P.
Shelf
2 pcs.
Q.
Side Rack
1 pc.
M.
Gate Leg
1 pc.
R.
Side Rack
1 pc.
T.
Brush Chrome Pipes
3 pcs.
E.
Middle
Panel
1 pc.
D.
Middle
Panel
1 pc.
S.
Base Rack
1 pc.
(For Drawer N&O packed in separate
carton with hardware and assembly
instructions.)
Caster
two lock
two non-lock
4 pcs.
X.
Door
1 pc.
W.
Door
1 pc.
O.
KD. Drawer
1 pc.
N.
KD. Drawer
3 pcs.
Head Cap Bolt
14 pcs. (+1 extra)
Adjustable Pin
8 pcs. (+2 extra)
U.
Handle Arm
2 pcs.
V.
Round Arm
1 pc.
Cam Lock
4 pcs.(+1 extra)
Cam Lock Screw
4 pcs.(+1 extra)
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
Small
Hex Wrench
1 pc.
Assembly Instructions 2/4
STEP 1
STEP 2
STEP 3
L
L
K
K
K
D
E
B
Attach four Casters
underneath Base (L)
with Wood Screws.
(See ‘Arrow’ sticker
indicating front side)
Assemble Front Piece (H1),
(H2) and Front Rail (K).
(See figure 1)
Attach
the
side of unit with Head Cap Bolts.
the assembled unit
to Middle Panel (D) and (E).
Attach Side Panel (B) to
Attach the Back Piece (G), Middle Panel (D)
and Back Piece (G), Middle Panel (E) onto the
Base (L).
G
G
D
E
H1
H2
Wood Screw
Wood Screw
Head Cap Bolt
Locking Caster
(On Front)
(Figure 1)
IMPORTANT
* Do not tighten up all the bolts until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
M
STEP 4
STEP 7
Slide Back Panel (F) into place.
Attach Back and Front
Stretcher (I), (J) to the unit
with Head Cap Bolts.
Attach Side Panel (C) to the other
side of unit with Head Cap Bolts.
J
C
I
Attach Gate Leg (M) at the rear
and connect it to the unit with
Wood Screws.
(See figure 2)
F
F
F
B
R
S
T
Q
STEP 5
Attach Side Rack (Q) to Side Panel (B) with
Head Cap Bolts.
Attach Brush Chrome Pipes (T) and Base Rack (S)
to the Side Rack (Q).
Attach Side Rack (R) to the Side Panel (B),
using Head Cap Bolts.
Head Cap Bolt
Head Cap Bolt
Wood Screw
Wood Screw
Head Cap Bolt
C
V
U
U
STEP 6
Attach Handle Arm (U) to Side Panel (C)
with Head Cap Bolts.
Slide the Round Arm (V) into place.
(Figure 2)
Assembly Instructions 3/4
STEP 8
STEP 9
STEP 10
Place Top (A) onto the unit.
and tighten
all Cam Locks as to secure the top with
the body.
Put Cam Locks into the holes of
the Side Panel (B) and (C)
Insert Adjustable Pins into the side
panels at the desired level.
Place Shelf (P).
A
P
W
X
N
N
N
O
P
A
B
B
D
E
C
C
Turn over Top (A) and put
Cam Lock Screws into the
pre-drilled holes. Tighten up
Cam Lock Screws.
STEP 11
Cover up all holes
with Wood Plugs.
Figure 1
Figure 2
Attach Pull Handles to the
Door (W) and (X) using Machine
Screws. (See figure 1)
Attach the Door (W) and (X) to
Side Panel (B) and (C), slide the
door lift hinges into the side panel
lift hinges. (See figure 2)
Slide the Drawers (N) and (O)
into place.
Cam Lock Screw
Cam Lock
Assembly Instructions 4/4
88508995 C
Drawer (N)
Assembly
Instructions
N3.
Side Part
1 pc. for each
drawer.
N4.
Side Part
1 pc. for each
drawer.
N5.
Base Part
1 pc. for each
drawer.
N2.
Back Part
1 pc. for each
drawer.
N2
N2
N5
N5
N3
N4
N4
N4
N3
N3
N1
N1
N1
Assemble the Pull Handle
with Machine Screw on
the Front Part (N1).
(Figure 1)
(Figure 2)
(Figure 3)
HARDWARE LIST
Pull Handle
3 pcs.
Machine Screw
for Pull Handle
6 pcs.
Wood Screw (short)
for base part
18 pcs.(+1 extra)
Wood Screw (long)
for side part
24 pcs.(+1 extra)
Insert the remaining (6) 1/2 screws
into the pre-drilled holes on Base Part
(N5), then tighten all screws.
”
make sure roller
is on the back
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.
N1.
Front Part
1 pc. for each
drawer.
N1
Slide the Plywood Base Part (N5) into
the grooves on Side Parts (N3) and (N4).
Be sure to push the plywood all the way
forward so it meets the Front Part (N1).
(See the figure 2)
Unfinished Side
UNIT PART LIST
Using a ,
insert 1” screws into the pre-drilled
holes as shown, tighten half way.
(See the figure 1)
philips screwdriver
88508995 C
Drawer (O)
Assembly
Instructions
O3.
Side Part
1 pc. .
O5.
Base Part
1 pc.
O2.
Back Part
1 pc. .
O2
O2
O5
O5
O3
O4
O4
O4
O3
O3
O1
O1
O1
Assemble the Pull Handle
with Machine Screw on
the Front Part (O1).
(See the figure 4)
(Figure 1)
(Figure 2)
(Figure 3)
(Figure 4)
HARDWARE LIST
Pull Handle
1 pcs.
Machine Screw
for Pull Handle
2 pcs.
Wood Screw (short)
for base part
6 pcs.(+1 extra)
Wood Screw (long)
for side part
8 pcs.(+1 extra)
Insert the remaining (6) 1/2 screws
into the pre-drilled holes on Base Part
(O5), then tighten all screws
(See the figure 3)
”
make sure roller
is on the back
* If you are missing any of these parts,
please contact our DMI Customer
Service Department at 1-877-831-0319
or fax us at 1-800-755-2878.
O1.
Front Part
1 pc.
Slide the Plywood Base Part (O5) into
the grooves on Side Parts (O3) and (O4).
Be sure to push the plywood all the way
forward so it meets the Front Part (O1).
(See the figure 2)
Unfinished Side
O4.
Side Part
1 pc.
O1
UNIT PART LIST
Using a , insert 1”
screws into the pre-drilled holes as shown,
tighten half way. (See the figure 1)
phillips screwdriver
/
