Johnson Controls CK721-A Operating instructions

April, 2012

24-10349-8 Revision B

CK721-A

Network Controller

Installation and Operation

Manual

CK721-A

Network Controller

Installation and Operation

Manual

April, 2012

24-10349-8 Revision B

Security Solutions

(805) 522-5555

www.johnsoncontrols.com

Johnson Controls, Inc.

No part of this document may be reproduced without the prior permission of Johnson Controls, Inc.

Acknowledgement

Cardkey P2000, BadgeMaster, and Metasys are trademarks of

Johnson Controls, Inc. All other company and product

names are trademarks or registered trademarks of their respective owners.

If this document is translated from the original English v

ersion by Johnson Controls, Inc., all reasonable endeavors

will be used to ensure the accuracy of translation. Johnson Controls, Inc. shall not be liable for any translation errors

contained herein or for incidental or consequential damages in connection with the furnishing or use of this

translated material.

Due to continuous development of our products, the informatio

n in this document is subject to change without

notice. Johnson Controls, Inc. shall not be liable for errors contained herein, or for incidental or consequential

damages in connection with the furnishing or use of this material. Contents of this publication may be preliminary

and/or may be changed at any time without any obligation to notify anyone of such revision or change, and shall not

be regarded as a warranty.

Federal Communications Comm

issions Notice

This equipment, CK721-A, has been tested and found to comply with the limits for a Class B digital device, pursuant

t

o Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

 Reo

rient or relocate the receiving antenna.

 In

crease the separation between the equipment and receiver.

 Connec

t the equipment into an outlet on a circuit different from that to which the receiver is connected.

 Consult the dealer or a

n experienced radio/TV technician for help.

The user is cautioned that changes and modifications made to t

he equipment without approval of the manufacturer

could void the user’s authority to operate this equipment.

Canadian Notice

This Class B digital apparatus, CK721-A, complies with Canadian ICES-003.

Cet appareil numerique de la classe B, CK721-A

, est conforme à la norme NMB-003 du Canada.

Declaration of Conformity

This product complies with the requirements of the EMC Directive 2004/108/EC and the Low Voltage

Directiv

e 2006/95/EEC.

This equipment must not be modified for any reason and i

t must be installed as stated in the Manufacturer’s

instruction.

If this shipment (or any part thereof) is supplied as second-hand equipment, equipment for sale outside the European

Econ

omic Area or as spare parts for either a single unit or system, it is not covered by the Directives.

UNDERWRITERS LABORATORIES® COMPLIANCE VERIFICATION SHEET

CK721-A SERIES INSTALLATION MANUAL

This product is listed under Underwriters Laboratories UL™ 1076 for Proprietary Burglar Alarm Units and Systems

and UL 294 for Access Control Systems Units. When installed at the site the following requirements must be met to

comply with these standards.

1. Transient protection devices that are installed must not be removed or defeated.

2. The CK721-A shall be mounted in subassembly S300-DIN-L or S300-DIN-S.

3. The CK721-A in combination with the S300-DIN-L or S300-DIN-S must be connected to a UL Listed

Uninterruptible Power Supply that provides a minimum of 24 hours of AC emergency power.

4. The tamper switch must be enabled at all times.

5. Systems requiring the use of network hubs, routers, bridges, network switches or the like shall guarantee

these devices are UL Listed for fire and shock in the category control number (CCN) NWGQ and/or EMRT.

These devices shall be installed in a temperature-controlled environment. The temperature-controlled envi

-

ronment must be maintained between 13 - 35°C (55 - 95°F) and relative humidity of 85 ± 5% by the HVAC

system. Twenty-four hour standby power shall be provided for the HVAC system.

6. The installer shall incorporate a supply line transient suppression device complying with the Standard for

Transient Voltage Surge Suppressors, UL 1449, with a maximum rating of 330 V. Supply line transient sup

-

pression device is to be used with the power supply to the network hub(s) routers, bridges and/or network

switches.

7. External network hubs, routers, bridges or network switches must use signal line transient suppression

devices complying with the Standard for Protectors for Data Communications and Fire Alarm Circuits, UL

497B, with a maximum marked rating of 50V.

8. In the CK721-A user-interface, the “Network Polling [LAN]” parameter must not exceed 90 seconds.

9. Modems shall not be used for primary connection to the host computer. Modems have only been investi-

gated by UL for supplementary use.

10. The use of the MTI-STI-MUX-KIT and MTI-STI-MUX has not been investigated by Underwriters Labora-

tories.

11. The Otis elevator interface has not been investigated by Underwriters Laboratories.

12. Do not connect equipment to an AC power source that is controlled by a switch.

13. The Kone IP elevator interface has not been investigated by Underwriters Laboratories.

14. Do not connect equipment to an AC power source that is controlled by a switch.

15. For CK721-A, provided as part of an SPA, SPB, and SPC security control panel assembly, items 1 and 4

through 13 apply.

16. The CK721-A, provided as part of an SPA, SPB, and SPC security control panel assembly, must be con-

nected to a UL Listed Uninterruptible Power Supply that provides a minimum of 24 hours of AC emergency

power.

TABLE OF CONTENTS

24-10349-8 Rev. B v

This document contains confidential and proprietary information of Johnson Controls, Inc.

1: Introduction

Manual Conventions ............................................................................................................................... 1-1

Key Terms............................................................................................................................................... 1-2

Unpacking the Equipment....................................................................................................................... 1-3

General Description ................................................................................................................................ 1-4

CK721-A Module ............................................................................................................................. 1-4

Enclosures ...................................................................................................................................... 1-5

Modules .......................................................................................................................................... 1-6

Additional Equipment ...................................................................................................................... 1-7

Specifications (All Panels) ...................................................................................................................... 1-8

CK721-A Panel Configuration................................................................................................................. 1-9

Expanded Address S300 Bus Configuration ................................................................................... 1-9

Legacy Address S300 Bus Configuration ....................................................................................... 1-9

System Configuration Example ..................................................................................................... 1-10

Maximum Enclosure Distance ....................................................................................................... 1-10

10/100Base-T Networking Guidelines (specific to the CK721-A).......................................... 1-10

Network Communication....................................................................................................................... 1-11

TCP/IP .......................................................................................................................................... 1-12

Addressing ............................................................................................................................ 1-12

10/100Base-T Ethernet ................................................................................................................. 1-12

Communication Modes ................................................................................................................. 1-13

CK721-A/P2000 Server Encrypted Communications .................................................................... 1-13

2: CK721-A and S300-DIN Enclosures

CK721-A ................................................................................................................................................. 2-1

LEDs on the CK721-A ..................................................................................................................... 2-2

Binary Output .................................................................................................................................. 2-3

Setting the End-of-Line Switch ........................................................................................................ 2-3

Lithium Battery ................................................................................................................................ 2-4

Input Power ..................................................................................................................................... 2-5

RS485 ............................................................................................................................................. 2-5

Binary Input ..................................................................................................................................... 2-6

Connecting the Network .................................................................................................................. 2-7

Hub to CK721-A Wiring........................................................................................................... 2-7

RS232 ............................................................................................................................................. 2-7

RS232 Serial Null Modem Cable Wiring ................................................................................. 2-8

Large Enclosure (S300-DIN-L) ............................................................................................................... 2-9

Wiring CK721-A and Modules ....................................................................................................... 2-11

CK721-A Cable Requirements.............................................................................................. 2-11

Chain Module Wiring............................................................................................................. 2-12

Cable Routing ....................................................................................................................... 2-12

Chassis Grounding................................................................................................................ 2-13

Table of Contents CK721-A Installation and Operation

vi 24-10349-8 Rev. B

This document contains confidential and proprietary information of Johnson Controls, Inc.

Small Enclosure (S300-DIN-S) ............................................................................................................. 2-13

Verifying DC and Chassis Ground ................................................................................................2-14

Installing CK721-A Module ............................................................................................................ 2-14

Cable Routing ....................................................................................................................... 2-15

Chassis Grounding................................................................................................................ 2-15

No Enclosure ........................................................................................................................................ 2-15

DIN Rail Mounting ......................................................................................................................... 2-15

+24 VDC Connector.............................................................................................................................. 2-16

Power Wiring ................................................................................................................................. 2-16

Ground Wiring ............................................................................................................................... 2-17

3: S300 Expansion Enclosures

S300 Expansion Enclosures ................................................................................................................... 3-1

Installing the Expansion Enclosures ............................................................................................... 3-1

Tools Required........................................................................................................................ 3-2

Sequence of Steps.................................................................................................................. 3-2

Planning the Installation.......................................................................................................... 3-2

S300-XL (S300 Expansion Enclosure, Large) ........................................................................ 3-3

S300-XS (S300 Expansion Enclosure, Small) ........................................................................ 3-4

S300-XXS (S300 Expansion Enclosure, Extra Small) ............................................................ 3-4

Removing the Knockouts ........................................................................................................ 3-5

Mounting the Enclosures ................................................................................................................. 3-6

Removing Boards from the Panels ......................................................................................... 3-6

Panel Location Suggestions.................................................................................................... 3-6

Installing the Power Supplies.................................................................................................. 3-7

Installing the First Level Modules .................................................................................................... 3-7

Installing the Second Level (Stacked) Modules ............................................................................ 3-10

Cabling .......................................................................................................................................... 3-12

Cabling Between Enclosures ................................................................................................ 3-13

Equipment Grounding ................................................................................................................... 3-16

Power.................................................................................................................................................... 3-16

S300-XFMR Transformer .............................................................................................................. 3-16

S300-PS Power Supply ................................................................................................................. 3-17

S300 Enclosure Power Consumption ........................................................................................... 3-19

Applying Power to the S300 Expansion Enclosure ....................................................................... 3-22

Legacy Reader Module......................................................................................................................... 3-23

Firmware Versions for Reader Modules ........................................................................................ 3-23

RS-485 Wiring ............................................................................................................................... 3-23

S300-RDR2 Module ...................................................................................................................... 3-25

Wiring Readers ............................................................................................................................. 3-28

Warm-up Resistor Removal.................................................................................................. 3-29

Wiring for Door Controls........................................................................................................ 3-35

Door Strike Wiring ................................................................................................................. 3-36

Door Open Detector Wiring................................................................................................... 3-37

Auxiliary Access Switch Wiring ............................................................................................. 3-37

Shunt Relay Driver Wiring..................................................................................................... 3-37

Legacy I/O Modules .............................................................................................................................. 3-38

Firmware Versions for Legacy I/O Modules .................................................................................. 3-38

RS-485 Wiring ............................................................................................................................... 3-38

S300-I16 Unsupervised Input Module ........................................................................................... 3-41

S300-IO8 Unsupervised Input/Output Module .............................................................................. 3-43

S300-SIO8 Supervised Input/Output Module ................................................................................ 3-45

CK721-A Installation and Operation Table of Contents

24-10349-8 Rev. B vii

This document contains confidential and proprietary information of Johnson Controls, Inc.

S300-SI8 Supervised Alarm Input Module .................................................................................... 3-47

Wiring Input/Output Devices ......................................................................................................... 3-48

Expansion Enclosure Tamper Switch Wiring ........................................................................ 3-48

Unsupervised Alarm Inputs ........................................................................................................... 3-48

Supervised Alarm Inputs ............................................................................................................... 3-50

Calibrating Four-State Alarm Inputs...................................................................................... 3-51

Output Relay Wiring ...................................................................................................................... 3-52

Output Wiring ................................................................................................................................ 3-53

Backup Battery...................................................................................................................................... 3-54

S300-BAT Battery ......................................................................................................................... 3-54

S300-BRK2 Battery Bracket Kit .................................................................................................... 3-55

Installing the Backup Battery ......................................................................................................... 3-55

4: CK721-A User Interface

Important Notes ...................................................................................................................................... 4-1

Notes on Encryption................................................................................................................ 4-2

Principle of Operation ............................................................................................................................. 4-2

Communicating with the User Interface ..........................................................................................4-3

Using your Terminal Emulation ....................................................................................................... 4-3

Navigating Through the User Interface ........................................................................................... 4-4

Write Flash ...................................................................................................................................... 4-6

Clearing Database .......................................................................................................................... 4-6

Clearing the Flash Memory ............................................................................................................. 4-7

Router Configuration ....................................................................................................................... 4-7

Notes on Adding IP Addresses in Route Configuration Screen:............................................. 4-8

Troubleshooting ...................................................................................................................... 4-8

CK721-A Static Route Examples ............................................................................................ 4-9

Log Out ........................................................................................................................................... 4-9

Rebooting the Panel ....................................................................................................................... 4-9

Basic Panel Configuration..................................................................................................................... 4-10

Panel Menu ................................................................................................................................... 4-10

Legacy Panel Menu ...................................................................................................................... 4-10

Panel ............................................................................................................................................. 4-11

Direct Programming of the CK721-A .................................................................................................... 4-12

Panel Screen Description .............................................................................................................. 4-13

Terminal ........................................................................................................................................ 4-19

Offline Access Card Type Requirements.............................................................................. 4-33

RDR8S Input Point and Output Point Disassociation .................................................................... 4-33

RDR2S-A Input Point and Output Point Disassociation ................................................................ 4-35

Configuring PIN Codes ................................................................................................................. 4-36

PIN Only................................................................................................................................ 4-36

PIN + Card ID........................................................................................................................ 4-36

PIN ........................................................................................................................................ 4-37

Four-Digit PINs...................................................................................................................... 4-37

PIN Duress............................................................................................................................ 4-37

PIN Plus 1 Duress................................................................................................................. 4-38

PIN Retry Alarm .................................................................................................................... 4-38

Assisted Access ............................................................................................................................ 4-38

ADA Relay............................................................................................................................. 4-39

Panel Entry/Exit ............................................................................................................................. 4-39

Badge Entry/Exit Options ...................................................................................................... 4-39

Table of Contents CK721-A Installation and Operation

viii 24-10349-8 Rev. B

This document contains confidential and proprietary information of Johnson Controls, Inc.

Elevator Access Control ................................................................................................................ 4-41

General Overview ................................................................................................................. 4-41

Standard Low Level Interface ............................................................................................... 4-41

D620-ECG Low Level Interface ............................................................................................ 4-42

KONE HLI/KONE ELINK High Level Interface...................................................................... 4-43

KONE IP High Level Interface............................................................................................... 4-44

KONE IP Elevator Support.................................................................................................... 4-44

OTIS E.M.S. - Security / B.M.S. Protocol High Level Interface............................................. 4-47

OTIS Compass High Level Interface..................................................................................... 4-50

Basic Definitions.................................................................................................................... 4-52

Performance Considerations................................................................................................. 4-53

Cabinet Access Control ................................................................................................................. 4-53

Elevator or Cabinet Terminal ........................................................................................................ 4-54

Output ........................................................................................................................................... 4-58

Holiday .......................................................................................................................................... 4-60

Access Group ................................................................................................................................ 4-61

Elevator Access Group ................................................................................................................. 4-62

Control Door .................................................................................................................................. 4-63

Panel Soft Alarm ........................................................................................................................... 4-64

Password Change ......................................................................................................................... 4-66

Reboot .......................................................................................................................................... 4-66

Badge ............................................................................................................................................ 4-67

Input .............................................................................................................................................. 4-71

Time Zone ..................................................................................................................................... 4-75

Card Events .................................................................................................................................. 4-76

System Information ....................................................................................................................... 4-81

Control Output ............................................................................................................................... 4-84

Change Date ................................................................................................................................. 4-85

5: Maintenance

Routine Maintenance.............................................................................................................................. 5-1

Impaired Performance Conditions .......................................................................................................... 5-1

Testing Procedure................................................................................................................................... 5-2

Check Backup Battery Operation .................................................................................................... 5-2

Lithium Battery Replacement .......................................................................................................... 5-2

Field Servicing ........................................................................................................................................ 5-3

Troubleshooting ...................................................................................................................................... 5-3

Appendix A: Expanded Address S300 Bus

Appendix B: Performance Analysis

Appendix C: Grounding and Connectors

Cable Grounding..................................................................................................................................... C-1

“D-Type” Connectors .......................................................................................................................C-2

Non “D-Type” Grounding Connections ............................................................................................C-3

Installations in the USA ...................................................................................................................C-3

Installations in Europe .....................................................................................................................C-4

Card Reader Unit Grounding .................................................................................................................. C-4

CK721-A Installation and Operation Table of Contents

24-10349-8 Rev. B ix

This document contains confidential and proprietary information of Johnson Controls, Inc.

Appendix D: Door Open/Aux Access Supervision

Purpose of Supervised Inputs................................................................................................................. D-1

Configuring the S300-SIO8..................................................................................................................... D-2

Wiring to the Reader Module .................................................................................................................. D-2

Appendix E: Database Flash Backup from the Host

Appendix F: Using a Keypad Reader on a Panel

Invoking Access Requests from a Keypad ............................................................................................. F-1

Invoking Air Crew Access Requests from a Keypad............................................................................... F-2

Invoking Timed Overrides from a Keypad............................................................................................... F-2

Invoking Panel Card Events from a Keypad ........................................................................................... F-5

Quick Guide to Using Keypad Readers .................................................................................................. F-8

Appendix G: Configuring SSH and SFTP Clients

PuTTY Client.......................................................................................................................................... G-1

WinSCP Client ....................................................................................................................................... G-5

Table of Contents CK721-A Installation and Operation

x 24-10349-8 Rev. B

This document contains confidential and proprietary information of Johnson Controls, Inc.

LIST OF FIGURES

24-10349-8 Rev. B xi

This document contains confidential and proprietary information of Johnson Controls, Inc.

Sample CK721-A System Configuration .......................................................................................................... 1-10

10/100Base-T 4x5 Rule ................................................................................................................................... 1-11

CK721-A/P2000 Server Encrypted Communications ...................................................................................... 1-14

Wiring Between RS485B and RDR2S Module .................................................................................................. 2-6

Wiring Between RS485B and S300 I/O Module ................................................................................................ 2-6

Wiring Between Binary Input 1 and Trouble Pin ................................................................................................ 2-6

Hub to CK721-A Wiring ...................................................................................................................................... 2-7

Large Enclosure With Installed Components ................................................................................................... 2-10

One CK721-A Module Mounted in a Large Enclosure ..................................................................................... 2-10

One CK721-A Module and Two RDR2S Modules Mounted in a Large Enclosure .......................................... 2-10

Daisy Chain Module Wiring for S300-DIN-L .................................................................................................... 2-12

Small Enclosure With Installed Components ................................................................................................... 2-13

One CK721-A Module Mounted in a Small Enclosure ..................................................................................... 2-14

CK721-A Module Mounted on a DIN Rail. ....................................................................................................... 2-16

+24 VDC Connector (Part of the DC Power Harness) ..................................................................................... 2-16

Wiring Multiple Modules - Overview ................................................................................................................. 2-17

S300-L ............................................................................................................................................................... 3-3

S300-XS ............................................................................................................................................................. 3-4

S300-XXS .......................................................................................................................................................... 3-4

S300 Expansion Enclosure Knockouts .............................................................................................................. 3-5

Mounting the Panels: S300-XL .......................................................................................................................... 3-6

Mounting the Panels: S300-XS .......................................................................................................................... 3-7

Mounting the Panels: S300-XXS ....................................................................................................................... 3-7

First Level Module Locations in S300-XL .......................................................................................................... 3-8

First Level Module Locations in S300-XS .......................................................................................................... 3-9

First Level Module Location in S300-XXS ......................................................................................................... 3-9

Stacked Module Locations in S300-XL ............................................................................................................ 3-10

Stacked module Locations in S300-XS ............................................................................................................ 3-11

Stacked Module Locations in S300-XXS ......................................................................................................... 3-11

Cable Assembly for Enclosure to Enclosure Connection ................................................................................. 3-14

Cable Assembly for Enclosure to Enclosure Connection - Details ................................................................... 3-15

Power Supply ................................................................................................................................................... 3-17

Wiring Diagram for Cable Connectors ............................................................................................................. 3-19

S300-RDR2 Module ......................................................................................................................................... 3-25

Maximum Distance Between Readers and S300 Expansion Enclosures ........................................................ 3-28

Wiring Diagram, Cardkey Keypad Reader ....................................................................................................... 3-30

Wiring Diagram, Single Data Wire Cardkey Readers ...................................................................................... 3-31

Wiring Diagram, Sensor Two Data Wire Wiegand Readers ............................................................................ 3-32

Wiring Diagram, Two Data Wire Proximity Readers ........................................................................................ 3-33

Wiring Diagram, Data Wire High Current or +24 Volt Proximity Readers ........................................................ 3-34

Example of a Typical CK721-A System ........................................................................................................... 3-35

List of Figures CK721-A Installation and Operation

xii 24-10349-8 Rev. B

This document contains confidential and proprietary information of Johnson Controls, Inc.

Field Installed Metal Oxide Varistor ................................................................................................................. 3-36

S300-I16 Module .............................................................................................................................................. 3-41

S300-IO8 Module ............................................................................................................................................. 3-43

S300-SIO8 Module .......................................................................................................................................... 3-45

S300-SI8 Module ............................................................................................................................................. 3-47

Wiring Input Points (two and four-state alarms) ............................................................................................... 3-49

Circuit for two-state Inputs (normally closed) ................................................................................................... 3-49

Four-state Alarm Inputs ................................................................................................................................... 3-50

Four-State Alarm Conditions ............................................................................................................................ 3-51

Configuration of Outputs .................................................................................................................................. 3-52

Field Installed Metal Oxide Varistor ................................................................................................................. 3-53

Battery Backup for Expansion Enclosures ....................................................................................................... 3-54

S300-BAT and S300-BRK2 Assembly ............................................................................................................. 3-55

Battery Mounting for S300-XL and S300-XXS ................................................................................................. 3-56

Battery Mounting for S300-XS ......................................................................................................................... 3-56

Battery Installation Location in S300-XL .......................................................................................................... 3-57

Battery Installation Location in S300-XS .......................................................................................................... 3-57

Battery Installation Location in S300-XXS ....................................................................................................... 3-58

CK721-A Controller/P2000 Host Connection Methods ...................................................................................... 4-3

Static Route Examples ....................................................................................................................................... 4-9

Assisted Access Timing Diagram .................................................................................................................... 4-39

KONE KIC Controller with Multiple Elevator Groups ....................................................................................... 4-45

KONE KIC Controller with Multiple Elevator Groups

and Multiple CK721-A Controllers .................................................................................................................... 4-46

Primary and Backup KONE IP Controllers ....................................................................................................... 4-46

Master-Slave Elevator Configuration Layout ................................................................................................... 4-47

Using Multiple Time Blocks .............................................................................................................................. 4-75

CK721-A Access Time Performance Graph ......................................................................................................B-2

Example of D-Type Connector Grounding .........................................................................................................C-2

Example of Grounding Shielded Cable at Both Ends ........................................................................................C-3

Example of Grounding Shielded Cable at Only One End ..................................................................................C-4

Input/Output Contact Wiring ...............................................................................................................................D-3

CK705/CK720 Write DB to Flash Dialog Box ....................................................................................................E-1

24-10349-8 Rev. B xiii

LIST OF TABLES

This document contains confidential and proprietary information of Johnson Controls, Inc.

CK721-A ............................................................................................................................................................ 1-4

S300 and S300-DIN Enclosures ........................................................................................................................ 1-5

Hardware Modules ............................................................................................................................................. 1-6

Additional Equipment ......................................................................................................................................... 1-7

CK721-A System Specifications ........................................................................................................................ 1-8

CK721-A LED Functions .................................................................................................................................... 2-2

Input Power ........................................................................................................................................................ 2-5

RS232 Connectors ............................................................................................................................................. 2-7

RS232 Ports Pinout ........................................................................................................................................... 2-8

Connectors Pinout ............................................................................................................................................. 2-9

RS232A to DB9 Connection .............................................................................................................................. 2-9

Cable Requirements ........................................................................................................................................ 2-11

Cable Types ..................................................................................................................................................... 3-12

S300 Expansion Enclosure AC Power Specifications ..................................................................................... 3-16

Power Supply Components ............................................................................................................................. 3-18

LEDs On Power Supply ................................................................................................................................... 3-18

Fuse Functions and Ratings ............................................................................................................................ 3-19

S300-RDR2 Power Consumption .................................................................................................................... 3-20

S300-I16 Power Consumption ......................................................................................................................... 3-20

S300-IO8 Power Consumption ........................................................................................................................ 3-21

S300-SIO8 Power Consumption ...................................................................................................................... 3-21

Legacy Reader Module Firmware Versions ..................................................................................................... 3-23

RS-485 Connector Positions ............................................................................................................................ 3-24

S300-RDR2 Components ................................................................................................................................ 3-26

Reader Module Address Settings .................................................................................................................... 3-27

Reader Module Connector Callouts ................................................................................................................. 3-28

S300-RDR2 Locations of Warm-up Resistors ................................................................................................. 3-29

Legacy I/O Module Firmware Versions ............................................................................................................ 3-38

RS-485 Connector Positions ............................................................................................................................ 3-39

Input/Output Module Terminal Address Settings ............................................................................................. 3-40

S300-I16 Components ..................................................................................................................................... 3-42

S300-IO8 Components .................................................................................................................................... 3-44

S300-SIO8 Components .................................................................................................................................. 3-46

S300-SI8 Components ..................................................................................................................................... 3-47

Cabling Requirements ..................................................................................................................................... 3-48

Factory Default IP Addresses and Network Mask ............................................................................................. 4-2

Required Settings - Panel Menu ...................................................................................................................... 4-10

Panel Screen, Page 1 ...................................................................................................................................... 4-13

Panel Screen, Page 2 ...................................................................................................................................... 4-15

Panel Screen, Page 3 ...................................................................................................................................... 4-18

List of Tables CK721-A Installation and Operation

xiv 24-10349-8 Rev. B

This document contains confidential and proprietary information of Johnson Controls, Inc.

Terminal Screen, Page 1 ................................................................................................................................. 4-20

Terminal Screen, Page 2 ................................................................................................................................. 4-23

Terminal Screen, Page 3 ................................................................................................................................. 4-25

Terminal Screen, Page 4 ................................................................................................................................. 4-31

Terminal Screen, Page 5 ................................................................................................................................. 4-32

Offline Access Card Type Requirements ......................................................................................................... 4-33

Elevator or Cabinet Terminal Screen, Page 5 ................................................................................................. 4-54

Setting Flags for Generating Floor Tracking Messages ................................................................................... 4-56

Elevator or Cabinet Terminal Screen, Pages 6 and 7 ...................................................................................... 4-57

Output Screen, 1 Page Only ............................................................................................................................ 4-59

Holiday Screen, 1 Page Only ........................................................................................................................... 4-61

Access Group Screen, 1 Page Only ................................................................................................................ 4-62

Elevator Access Group Screen, 1 Page Only .................................................................................................. 4-62

Control Door Screen, 1 Page Only .................................................................................................................. 4-64

Panel Soft Alarm, 1 Page Only ........................................................................................................................ 4-65

Password Change, 1 Page Only ...................................................................................................................... 4-66

Badge Screen, Page 1 ..................................................................................................................................... 4-69

Badge Screen, Page 2 ..................................................................................................................................... 4-70

Badge Screen, Page 3 ..................................................................................................................................... 4-71

Input Screen, 1 Page Only ............................................................................................................................... 4-73

Time Zone Screen, 1 Page Only ...................................................................................................................... 4-76

Card Event Overview ....................................................................................................................................... 4-77

Card Event Screen, Page 1 ............................................................................................................................. 4-78

Card Event Screen, Page 2 ............................................................................................................................. 4-79

System Information Screen, Page 1 ................................................................................................................ 4-81

System Information Screen, Page 2 ................................................................................................................ 4-83

System Information Screen, Page 3 ................................................................................................................ 4-83

Control Output Screen, 1 Page Only ............................................................................................................... 4-84

Results of Command Override on a Selection ................................................................................................. 4-85

Impaired Performance Conditions ..................................................................................................................... 5-1

Troubleshooting Guidelines ............................................................................................................................... 5-3

CK721-A Using Legacy Addressing Mode .........................................................................................................B-1

CK721-A Using Physical Addressing Mode .......................................................................................................B-1

Input/Output Linking, S300-SIO8, SW1 position 4 set ON .................................................................................D-2

24-10349-8 Rev. B 1-1

Chapter

1

This document contains confidential and proprietary information of Johnson Controls, Inc.

INTRODUCTION

This chapter provides a general description of the CK721-A panel and related equipment.

The conventions used throughout this manual are also described.

The manual is divided into the following chapters:

 Chapter 1: Introduction, defines the key terms and conventions used throughout the

manual. In addition, it describes the standard and optional equipment available for

the CK721-A and the equipment’s specifications. This chapter also includes

information on planning a CK721-A installation.

 Chapter 2: CK721-A and S300-DIN Enclosures, describes S300-DIN enclosures

and the components located on the CK721-A.

 Chapter 3: S300 Expansion Enclosures, provides information on the expansion

enclosures, principles to consider when installing the panels, and also contains a

section on preparing the panels for operation.

 Chapter 4: CK721-A User Interface, explains how to configure the panel for

operation and how to use the interface to commission or troubleshoot the system.

 Chapter 5: Maintenance, provides information on CK721-A routine maintenance

and the basic troubleshooting steps that will assist you in keeping the CK721-A

system running at peak performance.

 Appendices provide reference information regarding cabling and grounding and a

guide to using a keypad reader. They also contain information on the expanded

address S300 bus configuration with related performance analysis. The SSH and

SFTP client configuration is explained as well.

NOTE

Some features described in this manual are available depending on the

firmware version of your controller. For details, refer to the CK721-A

Software Release Notes.

MANUAL CONVENTIONS

The following items are used throughout this installation manual to indicate special

circumstances, exceptions, important points regarding the equipment or personal safety, or to

emphasize a particular point.

Introduction CK721-A Installation and Operation

1-2 24-10349-8 Rev. B

This document contains confidential and proprietary information of Johnson Controls, Inc.

NOTE

Notes indicate important points or exceptions to the information provided in

the main text.

IMPORTANT

Important messages remind you that certain actions, if not performed

exactly as stated, may cause damage to equipment or make your system

non-operational.

CAUTION

Caution messages indicate a potentially hazardous situation which, if

not avoided, may result in minor or moderate personal injury and/or

damage to equipment or property other than only the device itself.

KEY TERMS

NOTE

Throughout this manual, the S300-DIN modules and the S300 modules

are also referred to by their short name version. Refer to Table 1-3 for

details.

The following terms are used throughout this manual:

Advanced Encryption Standard (AES) – Encry

ption standard adopted by the U.S. government

in 2002; it supersedes DES. AES uses a symmetrical key algorithm.

CK721-A System – This is a general term that refers to a

combination of CK721-A terminals

and expansion enclosures that communicate with the P2000 system.

CK721-A – The CK721-A contains:

 A 10/100Base-T Network Interface

 A Hitachi SH-4 processor

 System memory for storing cardholder records, system parameters, and history

 A serial connection for communication with the user interface

 An RS-485 connector for communication to the modules

Encryption – The process of changing data into a form

that can be read only by the intended

receiver. To decrypt the message, the receiver of the encrypted data must have the proper

decryption key (generally protected by a strong password).

CK721-A Installation and Operation Introduction

24-10349-8 Rev. B 1-3

This document contains confidential and proprietary information of Johnson Controls, Inc.

Expansion Enclosure – An expansion enclosure contains only a power supply, a tamper

switch and a power indicator. The indicator can be seen when the cabinet door is closed.

External Device – This general term applies to any device that is wired to the CK721-A

system, such as a reader or input device. A motion sensor is one type of input device.

File Transfer Protocol (FTP) – A standard network protocol used to transfer files from one

host to another over a TCP-based network.

Modules – The modules provide additional reader interfaces, input points, or output relays to

the CK721-A system. Modules can be installed in the S300 expansion enclosures; RDR2S,

RDR2S-A, I8O4, RDR8S, and I32O16 modules can be installed in the S300-DIN

enclosures.

Panel – This generic term refers to an enclosure with the CK721-A and power supply

installed. The panel contains a tamper switch, a power indicator light, and an optional battery

backup.

Secure FTP (SFTP) – A program that uses SSH to transfer files. Unlike standard FTP, it

encrypts both commands and data, preventing passwords and sensitive information from

being transmitted in the clear over the network. It is functionally similar to FTP, but because

it uses a different protocol, you can't use a standard FTP client to talk to an SFTP server, nor

can you connect to an FTP server with a client that supports only SFTP.

Secure Shell (SSH) – A network protocol that allows data to be exchanged using a secure

channel between two networked devices.

Telnet – A network protocol used on the Internet or local area networks to provide a

bidirectional interactive text-oriented communications facility using a virtual terminal

connection

User Interface – The CK721-A User Interface provides access to the CK721-A panel

configuration graphical user interface (GUI) via a serial connection to a laptop (or other

computer) running common terminal emulation software or via Telnet/SSH/SFTP network

connection.

UNPACKING THE EQUIPMENT

Carefully inspect the shipping containers as soon as you receive them (with the delivery

agent present). Some shipping companies want to have an agent present when a damaged

container is opened. If a container is damaged, open it immediately, inspect the contents, and

have the agent make note on the shipping document. Check the purchase order against the

packing slips to ensure the order is complete. If the contents of a container are damaged in

any way, notify the carrier and your Johnson Controls

®

representative immediately. Report

any discrepancies to your Johnson Controls representative. Save the packing materials for

possible return shipments.

Introduction CK721-A Installation and Operation

1-4 24-10349-8 Rev. B

This document contains confidential and proprietary information of Johnson Controls, Inc.

GENERAL DESCRIPTION

All CK721-A panels are connected via a 10/100Base-T Ethernet network to the P2000

system. The CK721-A is intended to be mounted in an S300-DIN enclosure (large or small).

Each model has a total capacity 200,000 cards and a 8000 off-line transaction base memory.

NOTE

When the number of badges exceeds 120,000, the number of access

groups should be limited to 50,000.

CK721-A panels are connected via standard 10/100Base-T cabling and 10/100Base-T hubs.

The CK721-A is programmed and monitored via the P2000. The CK721-A provides its own

user interface through the serial connection located on the CK721-A. This interface

facilitates the initial setup, as well as commissioning and troubleshooting.

The CK721-A is an advanced, intel

ligent controller. You can add modules to connect

readers, monitor 2 or 4-state input points, and add output relays to perform manual or

automatic control functions. In addition, input points can be linked to output relays.

Communication between the CK721-A and the modules is accomplished via RS-485 per

Cardkey implementation. The CK721-A uses the following modules:

 Legacy S300 modules (RDR2S, S300-RDR2, S300-I16, S300-IO8, S300-SIO8,

S300-SI8)

 RDR2SA

 I8O4

 RDR8S

 I32O16

CK721-A does not support the Dial-Up feature.

NOTE

CK721-A version 3.0 and higher does not support MTI-STI-MUX with STI

and STI-E.

CK721-A Module

Table 1-1: CK721-A

Model Number Description

CK721-A A CK721-A module. Total storage capacity: 200,000 cards

an

d 8000 off-line transactions.

Note: Whe

n the number of badges exceeds 120,000,

the number of access groups should be limited to 50,000.

Page is loading ...

Johnson Controls CK721-A Operating instructions

Johnson Controls CK721-A Operating instructions

Related papers

Other documents