Cayman
Installation Guide
TYPICALS 1-10
PRIVATE OFFICE
CM1001
2CM1001 - Cayman Installation Instructions
1 — TOOLS AND SUPPLIES REQUIRED
Marker
3CM1001 - Cayman Installation Instructions
2 — INCLUDED PARTS AND FASTENERS
4CM1001 - Cayman Installation Instructions
2 — INCLUDED PARTS AND FASTENERS
5CM1001 - Cayman Installation Instructions
3.1 (Single Plinth)
3.3 (Multiple Plinths)
3.2 (Multiple Plinths)
3 — ASSEMBLY
3.4
6CM1001 - Cayman Installation Instructions
Note: Remove doors and drawers for easier assembly.
Tower options to be located in a later step.
Note: Be sure to use the 4 additional screws on the front
edge of the cantilever bottom plate (If present).
Note: If a Tower option is to be present, be sure to account for
that measurement.
3.5
3.7 3.8
3.6
3 — ASSEMBLY
7CM1001 - Cayman Installation Instructions
Cabinet Seam
Cabinet
Note: The Wall Support Anchor MUST be anchored in to a stud
in the wall using either (B)3/8 X 2” Hex Lag Bolt (wood stud) or
(M)1/4 X 2” Hex Lag Bolt (metal stud)
3.9
3.11
3.10
3 — ASSEMBLY
Attach the connection plate to the wall mounting bracket
using (K) 3/8-16 x.625” Serrated Hex Head bolts.
Note: Do not fully tighten. Location of the connection plate may
require adjustment prior to complete installation.
3.12
(L)
(L)
(L)
(L)
8CM1001 - Cayman Installation Instructions
Note: At this time it is advised to feed any power unit cords and
light cords to the cases.
Note: The wall panel will rest on the top of the lower case.
At this time it is advised to feed any light cords to their drivers
as there will be minimal room to route cords behind the walls.
Note: Use Cover caps if needed.
3.13
3.15
3.14
3 — ASSEMBLY
Note: Wall anchor hardware not provided for this step.
Does not require connection to stud.
3.16
(P)
(A)
(C)
9CM1001 - Cayman Installation Instructions
Note: Install these 2 screws towards the back edge of the
grommet.
3.17 (Otional Cantilever Column)
3.19 (Optional Height-Adjustable Table Column)
3.18
3 — ASSEMBLY
Note: Fixed top will have an additional (2x) M8 x 25mm on the
backside of the column.
3.20 (Optional Table Column)
(D)
(L) (L)
10CM1001 - Cayman Installation Instructions
Note: (Optional Utility Tray) Make sure that the power cords are
not pinched between the work surface and the metal frame.
3.21 (Otional Utility Column)
3.23
3.22
3 — ASSEMBLY
3.24 (Optional Table Column)
(A)
(A)
11CM1001 - Cayman Installation Instructions
Note: For HA Tables, be sure the modesty panel
will not collide with the lower case.
Note: End trim pieces are symmetrical. RH or LH determine by
which end the button x clip is installed on.
Install the Vertical Filler Panel by engage the button x clips and
magnets.
Note: For HA Tables, be sure the modesty panel
will not collide with the lower case.
3.25 (Otional Laminate Modesty Panel)
3.25
3.26 (Otional Acrylic Modesty Panel)
3 — ASSEMBLY
3.26
(P)
(N)
(L)
(L)
1.800.815.7251
enwork.com
12900 Christopher Dr. Lowell, MI 49331
Specications subject to change without notice.
Rev 03.2023
/
