Schwaiger HA102 User manual

Category
Networking
Type
User manual
USER MANUAL
Home Automation Gateway
HA102
TABLE OF CONTENTS
1. IMPORTANT SAFETY INFORMATION ....................................... 4
2. DEVICE DESCRIPTION ................................................... 5
3. INSTALLATION OF THE SCHWAIGER GATEWAY ............................. 6
3.1 WIFI CONFIGURATION OF THE GATEWAY .................................................................................................... 7
4. CONFIGURING SCHWAIGER HOME AUTOMATION SYSTEM .................. 8
4.1 INSTALL SCHWAIGER CLIENT APPLICATION ............................................................................................ 9
4.2 CREATE USER ACCOUNT ............................................................................................................................................9
4.2.1 Create user account by using client application ..............................9
4.2.2 Create user account by using web application ..............................10
4.3 ADD THE GATEWAY TO THE USER ACCOUNT .......................................................................................10
4.3.1 Add the gateway by using client application ................................11
4.3.2 Add the gateway by using web application .................................11
4.4 HOME SETUP ....................................................................................................................................................................... 12
5. DEVICE MANAGEMENT ..................................................13
5.1 MANAGE DEVICES BY USING CLIENT APPLICATION ....................................................................... 13
5.1.1 Add a device to the gateway ...............................................13
5.1.1.1 Z-Wave-specific information related to device inclusion .............15
5.1.2 Remove a device .........................................................15
5.1.3 Update device name and location ..........................................16
5.2 MANAGE DEVICES BY USING GATEWAY’S MAIN BUTTON .......................................................... 16
5.2.1 Add a device to the gateway ...............................................16
5.2.2 Remove a Z-Wave device ..................................................16
6. HA102 AS A PART OF OTHER Z-WAVE CONTROLLER’S NETWORK ............17
7. CONTROLLING AND MONITORING DEVICES ...............................17
7.1 DEVICES BY LOCATION ................................................................................................................................................ 17
7.2 DEVICES BY TYPE ..............................................................................................................................................................17
7.3 ADVANCED DEVICE CONFIGURATION .......................................................................................................... 18
8. SCENE MANAGEMENT ...................................................18
8.1 CREATE NEW SCENE .....................................................................................................................................................18
8.2 RUN THE SCENE ................................................................................................................................................................21
8.3 EDIT THE SCENE ............................................................................................................................................................... 21
8.4 DELETE THE SCENE ....................................................................................................................................................... 21
8.5 DISABLE THE SCENE ....................................................................................................................................................22
9. RESET CONFIGURATION ................................................22
9.1 RESET NETWORK CONFIGURATION .............................................................................................................. 22
9.2 RESET USER PREFERENCES ................................................................................................................................22
9.3 FACTORY RESET ............................................................................................................................................................. 22
10. BUTTONS/FUNCTIONS .................................................23
11. TECHNICAL DATA ......................................................23
12. DECLARATIONS OF CONFORMITY .......................................23
4
Congratulations and thank you for purchasing Schwaiger Home Automation
Gateway device. Below you will find useful operating guidelines.
WARNING!
The 5V port of this unit is to be connected only to the devices whose power feeding
meets the requirements for SELV (Safety Extra Low Voltage) and complies with Limited
Power Source according to IEC 60950-1.
1. IMPORTANT SAFETY INFORMATION
Before using Schwaiger Home Automation Gateway, please read the following information to avoid
any potential dangers:
1. Read the instructions carefully and follow the precautions in this manual. All mains connec-
tions must be carried out by a trained and qualified person
2. Only use the original mains adaptor supplied with the device
3. Disconnect the device from mains (mains chargers) before cleaning. Clean device with a
damp cloth, do not use detergents
4. Do not use device in gas-filled environments
5. Do not place the device near heat sources
6. Do not expose the device to direct sunlight
7. Do not place cables and/or power supplies under heavy objects. Also, avoid routes near sharp
or abrasive objects and walkways
8. Keep out of reach of children
9. Do not carry out any maintenance on the device, instead contact your supplier
10. Make sure that ventilation slots and the cooling unit are not covered
11. As the device generates heat, this can lead to discoloration on the surface of furniture. Make
sure there is at least 10cm of clearance around the device
12. The device must not be located in the rooms with a high level of humidity e.g. kitchen, bath-
rooms, etc.
13. Under no circumstances should you open the device or the mains adaptor. This must only be
carried out by a qualified engineer
14. Do not touch any contacts on the device with your fingers or metal objects. This could cause
a short circuit
15. Do not handle the device when your hands are wet due to risk of electric shock
5
2. DEVICE DESCRIPTION
Schwaiger home automation gateway takes central place in home automation system.
Combined with Schwaiger client (Android/iOS/HTML) applications and Schwaiger cloud service
it provides a turnkey platform that covers lighting, security, safety, energy management and other
aspects of the fast-growing home automation markets.
By supporting the most popular wireless communication protocols today (Zigbee, Z-Wave, IP),
Schwaiger gateway communicates with connected devices and enables users to monitor and con-
trol their home.
Illustration 1: Schwaiger home automation gateway
Schwaiger home automation gateway consists of:
MAIN button, which is used to manage home automation devices
BACK button, which is used to reset user data, reset the gateway network, reboot the gateway
and reset the gateway to factory default settings
LED indicator informs user about gateway status
Power supply socket
Ethernet
Use of these buttons is described in more detail in the corresponding section of this manual (page 23).
Main button
FRONT
BACK
Power supply socket Back button Ethernet
LED indicator
6
3. INSTALLATION OF THE SCHWAIGER GATEWAY
In order to install your Schwaiger gateway, please follow next steps:
1. Plug in the Home Automation Gateway to the AC power supply
2. Connect the Gateway to the home network router by using Ethernet ( Illustration 2) or WiFi
Connection (Illustration 3)
Illustration 2: Ethernet connection
Illustration 3: WiFi connection
In case you have connected your gateway device to the home network router by using Ether-
net cable, the installation process is done and you can proceed to the Section 4 (Configuring the
Schwaiger home automation system).
7
3.1 WIFI CONFIGURATION OF THE GATEWAY
In case you would like to connect the gateway device to the home network router by using WiFi
connection, please follow next steps:
1. After powering up, the gateway enters AP (Access Point) mode if Ethernet cable is not con-
nected. In AP mode LED will blink blue. In this mode gateway creates its own WiFi network
that allows the end user to configure it for connection to home network router over WiFi
(gateway’s SSID or network name is printed on the label on the back side of the device)
2. Connect your client device (PC, tablet or smart phone) to the WiFi network created by gateway
3. In web browser of your client device launch default IP address printed on the label on the
back side of the gateway (typically 192.168.1.1). Device information page should be displayed
as shown in Illustration 4
Illustration 4
4. In main menu select “WiFi configuration” page as shown in Illustration 5, after which gateway
should list all available WiFi networks in your home
Illustration 5
5. After selecting your home network router’s WiFi network, type in the password and press
Apply” button to finish WiFi configuration of your gateway
6. Upon successful operation LED should go green indicating that your gateway is connected to
your home network router’s WiFi network. Otherwise, repeat the procedure starting from step 1
8
4. CONFIGURING SCHWAIGER HOME AUTOMATION
SYSTEM
Schwaiger Home Automation system consists of:
Schwaiger client application
Schwaiger home automation gateway
Schwaiger cloud
Illustration 6: Our System
Schwaiger client application is intuitive and easy to use. Its comfortable graphical user interface will
smoothly guide users through the process of configuration of their space. The app can be used both
in-home or remotely – it is smart enough to connect to the gateway directly if possible, to ensure
the best user experience.
Schwaiger home automation gateway takes central place in home automation system.
Combined with Schwaiger client (Android/iOS/HTML) applications and Schwaiger cloud service
it provides a turnkey platform that covers lighting, security, safety, energy management and other
aspects of the fast-growing home automation markets.
Schwaiger cloud plays an important role in Schwaiger home automation system, since it enables
home control outside local network. Built around modern web technologies, it ensures the highest
security and robustness with the lowest latency in home automation communication chain. It also
allows monitoring and controlling of the home from any browser-based device.
Please follow next steps for configuring Schwaiger Home Automation system:
1. Install Schwaiger client application
2. Create user account
3. Add the gateway to the user account
4. Home setup
9
4.1 INSTALL SCHWAIGER CLIENT APPLICATION
In order to start configuring Schwaiger home automation system, the user needs to install
Schwaiger client application. By using client application, users can control their household devices
and manage their accounts as well as the list of their gateways and configuration options.
Schwaiger client app is available for download at the Apple and Google application stores.
4.2 CREATE USER ACCOUNT
Account registration may be done in two ways:
1. By using client application
2. By using web application at https://home4you.schwaiger.de
4.2.1 Create user account by using client application
Please follow next steps in order to create new account:
1. To create a new user account by using client application make sure that your smart phone or
tablet is connected to the Internet and start the application.
2. Tap the “Create new account” button on the login dialog (see Illustration 7)
Illustration 7 Illustration 8
3. Enter a valid email address and the password on the login dialog (Illustration 8)
4. Agree with Terms of service and Privacy Policy and tap the button . The complete text of
Terms of service and Privacy Policy can be reviewed by tapping the “Terms of service” and
“Privacy Policy” buttons
5. Enter the account details and tap the button . Entries indicated by an asterisk (*) are man-
datory entries. All other entries can also be filled in later (see Illustration 9)
6. Enter your personal information and tap the button to close the wizard (see Illustration 10)
7. Once the account has been successfully registered, a verification link will be sent to the email
address specified in the account name (make sure to check Spam folder). Otherwise, a failure
notice will be displayed
8. Confirm the activation link sent in the email message
10
Illustration 9 Illustration 10
4.2.2 Create user account by using web application
Please follow next steps in order to create new account:
1. Visit https://home4you.schwaiger.de
2. Tap the “Don’t have an account” button on the login dialog (see Illustration 11).
3. Enter your personal and login information on the login dialog (see Illustration 12).
Illustration 11 Illustration 12
4. Agree with Terms of service and Privacy Policy and tap the button REGISTER. The complete
text of Terms of service and Privacy Policy can be reviewed by tapping the “Terms of service”
and “Privacy Policy” buttons
5. Once the account has been successfully registered, a message with an activation link will be
sent to the email address specified in the account name (make sure to check Spam folder).
Otherwise, a failure notice will be displayed.
6. Confirm the activation link sent in the email message
4.3 ADD THE GATEWAY TO THE USER ACCOUNT
The gateway can be added to the user account in two ways:
1. By using client application
2. By using web application
NOTE: More than one gateway can be added to the user account.
11
4.3.1 Add the gateway by using client application
Please follow next steps in order to add the gateway to the user account:
1. Make sure that your smart phone/tablet and the gateway are active within the same network
2. Open the Schwaiger application and log into the user account
3. Select Home Setup option from the main menu (Illustration 13)
4. On the Home Setup screen tap the “Add gateway” button in the upper right corner (Illustration 14)
Illustration 13 Illustration 14
5. Enter required gateway information:
a. Security ID – is a unique, secret identifier for a gateway. It consists of 16 characters (com-
bination of letters and numbers) and can be found on the back side of the Safety Infor-
mation card that comes in a box together with your gateway device.
b. Serial number – a unique identifier for every gateway device. It consist of 12 characters
(e.g. CDD9078CC00) and can be found on bottom of the device
c. Name – choose a name for your gateway
6. Tap the button to add the gateway and continue the home configuration process
7. If the gateway has been added, a success message will be displayed
4.3.2 Add the gateway by using web application
Please follow next steps in order to add the gateway to the user account:
1. Visit https://home4you.schwaiger.de and log into the user account
2. Select My equipment option from the main menu
3. On the My equipment screen tap the button in order to add the gateway to the user
account (Illustration 15)
Illustration 15
12
4. Enter required gateway information:
a. Security ID – is a unique, secret identifier for a gateway. It consists of 16 characters (com-
bination of letters and numbers) and can be found on the back side of the Safety Infor-
mation card that comes in a box together with your gateway device.
b. Serial number – a unique identifier for every gateway device. It consist of 12 characters
(e.g. 7CDD9078CC00) and can be found on bottom of the device
c. Name – choose a name for your gateway
5. Tap the SAVE button to add the gateway and continue the home configuration process. If the
gateway has been added, a success message will be displayed
4.4 HOME SETUP
The user can setup its smart home by using Schwaiger client application. To setup the home, please
follow next steps:
1. Make sure that your smart phone/tablet and the gateway are active within the same network
2. Log in to the account to which the gateway was added
3. Select Home Setup option from the main menu to open a list of the gateway devices asso-
ciated with the account
4. Find the gateway in the list and press gear button to open the options menu
5. Select the Edit option
6. In the first step, the user is able to change the name of the gateway. Tap the button to
continue managing the associated floors and rooms
7. In the second step, the user can manage associated floors:
a. To add a new floor, tap the button + in the upper right corner and enter a floor name
b. To delete the floor, tap the floor button and hold it until the delete option appears.
NOTE: All of the rooms associated with the floor will be deleted once the floor is deleted.
Devices associated with those rooms will be unsorted.
c. To change the floor name, briefly tap on the existing floor name (Illustration 16)
8. To continue managing rooms, tap the button :
a. To add a new room, choose the floor at which you want to add the room and tap the
button + in the upper right corner to enter a room name
b. To delete the room, select the floor at which the room is located, tap and hold the room
name until the delete option appears
NOTE: Devices associated with the deleted room will be unsorted.
c. To change the room name, briefly tap on the existing room name (Illustration 17)
Illustration 16 Illustration 17
13
9. Once you are satisfied with the home configuration, tap the button to continue to Device
Man agement section.
5. DEVICE MANAGEMENT
HA102gateway is compliant with Z-Wave Plus specification. It can be included and operated in
any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other
applications. All non-battery operated nodes within the network will act as repeaters regardless of
vendor to increase reliability of the network.
HA102 gateway is also compliant with ZigBee Home Automation (ZHA) 1.2 and is guaranteed to
function with any ZHA 1.2-compliant devices
To manage devices, the user should choose one of the following ways:
1. By using client application (recommended way to manage devices)
2. By using gateway’s main button
5.1 MANAGE DEVICES BY USING CLIENT APPLICATION
In order to open Device management section select Home setup option from the applications main
menu, for desired gateway press gear button to open the options menu and select option Add
device.
In the Device Management section the user is able to:
1. Add a device to the gateway
2. Remove a device
3. Update device name and location
5.1.1 Add a device to the gateway
Please follow next steps in order to add a new device to the gateway:
1. Tap the “Help” button in the upper right corner
2. Select the device which you want to add to the gateway and read instructions for adding the
device (Illustration 18)
Illustration 18
3. After having read the instructions, make sure that the device is removed from the previous
14
network first. If this is the case, please proceed to step 4.
In case of Z-Wave devices, device removal from previous network can be done by following
next steps:
a. Tap the button in the upper right corner and select “Exclude Device” option (see
Illustration 19). This action will open a new window for removing the device from previous
Z-Wave network. The remaining time for device removal will be displayed (see Illustration
20)
b. Follow manufacturer’s instructions for device removal since the process may vary from
device to device
Illustration 19 Illustration 20
In case of ZigBee devices, device removal from previous network should be done according
to manufacturer’s instructions.
4. In order to add new device tap the “Find devices” button in the upper left corner. This action
will open a new window for adding the device. The remaining time for device integration will
be displayed (see Illustration 21).
5. Add the device based on manufacturer’s instructions, since the process may vary from device
to device.
6. Once the device is added to network, it will be displayed among the list of devices (Illustration 22).
NOTE: During inclusion procedure the end user is able to abort it by pressing “Cancel” button. This
will close ZigBee, Z-Wave and IP networks.
Illustration 21 Illustration 22
15
5.1.1.1 Z-Wave-specific information related to device inclusion
If another Z-Wave controller is added to HA102 gateway, it will initiate network information replica-
tion from the HA102 gateway to the included controller.
HA102 gateway ignores any basic command class commands from devices.
HA102 Gateway supports Association Command Class. It implements one association
group, which is Lifeline group with grouping identifier equal to 1. This group returns Device Reset
Locally notification when the device is reset. Maximum number of devices that can be added to
the group is 5.
HA102 gateway allows the end user to control device associations in following way:
1. Go to device advanced configuration as described in Section 7.3
2. In selected association group fill “Node list” field with “Node ID” values (separated by com-
mas) of all devices that need to be associated to (e.g. “Node list” field: 4,6,7)
NOTE: “Node ID” field of each Z-Wave device can be found in device advanced configuration.
HA102 gateway allows the end user to control device multichannel associations in following way:
1. Go to device advanced configuration as described in Section 7.3
2. In selected multichannel association group fill “Node list” field with “Node ID”/”Endpoint”
values (separated by commas) of all devices that need to be associated to (e.g. “Node list”
field: 4/1,6/2,7/2)
NOTE: “Node ID” field of each Z-Wave device can be found in device advanced configuration.
5.1.2 Remove a device
Please follow next steps in order to remove a device:
1. Tap on the device name and hold it until the “Delete” option appears (see Illustration 23)
2. The type of device (ZigBee or Z-Wave) will determine which of the following processes should
be used:
a. In case of ZigBee device, you just need to confirm deletion
b. In case of Z-Wave device, the network will be opened for exclusion process. Once the
network is opened, the device needs to be excluded manually according to manufacturer’s
instructions (see Illustration 24)
Illustration 23 Illustration 24
16
5.1.3 Update device name and location
To update device name and location, please follow next steps:
1. Tap on the device name and hold it until the “Edit” option appears
2. Tap on the “Edit” button
3. In the new dialog, change the device name and choose the device location from the drop down
list (Illustration 25)
4. Tap the button OK
Illustration 25
5.2 MANAGE DEVICES BY USING GATEWAY’S MAIN BUTTON
By using gateway’s main button, the user is able to:
1. Add a device to the gateway
2. Remove a device (this applies only to Z-Wave devices)
5.2.1 Add a device to the gateway
Please follow next steps in order to add a new device to the gateway:
1. Short press gateway’s main button 2 times to open network for device inclusion. While net-
work is open LED will blink blue once per second
2. Start adding procedure on the device according to manufacturer’s instructions
3. Upon successful operation LED will blink light purple 4 times. There should also be visual
indication on the added device (see manufacturer’s instructions)
NOTE: During inclusion procedure the end user is able to abort it by pressing main button 2 times.
This will close ZigBee, Z-Wave and IP networks.
5.2.2 Remove a Z-Wave device
Please follow next steps in order to remove a Z-Wave device:
1. Short press gateway’s main button 4 times to start Z-Wave device exclusion procedure.
During the operation, LED will blink blue 5 times per second
2. Start exclusion on the Z-Wave device according to manufacturer’s instructions
3. Upon successful operation LED will blink light purple 4 times. There should also be visual
indication on the excluded device (see manufacturer’s instructions)
17
6. HA102 AS A PART OF OTHER Z-WAVE
CONTROLLER’S NETWORK
In order to add HA102 gateway into other controller’s Z-Wave network, please follow next steps:
1. Start learn mode by pressing back button 12 times. After entering learn mode, LED will blink
blue 2 times per second.
2. Start inclusion procedure on the other controller according to manufacturer’s instructions.
3. Upon successful operation, HA102 will be added to other controller’s Z-Wave network with fol-
lowing notes:
all Z-Wave devices that were previously included to HA102 will be deleted. These devices
became orphans and need to be added to the other controller’s Z-Wave network
Controller replication is implemented at minimum level and it is enabled by placing the
controller in the learn mode
7. CONTROLLING AND MONITORING DEVICES
7.1 DEVICES BY LOCATION
Please follow next steps in order to control or monitor devices by location:
1. Select Device by location option in the applications main menu
2. To filter devices by location, choose a desired location from the menu on the left side
3. In a quick control dialog on the right side (Illustration 26), the user is able to control actuators
(e.g. light on/o) and monitor sensors (e.g. read the temperature)
4. To release the filter, tap the home icon in the upper left corner
7.2 DEVICES BY TYPE
Please follow next steps in order to control or monitor devices by type:
1. Select Device by type option in the applications main menu
2. To filter devices by type, choose a desired type from the menu on the left side
3. In a quick control dialog on the right side (Illustration 27), the user is able to control actuators
(e.g. light on/o) and monitor sensors (e.g. read the temperature)
4. To release the filter, tap the home icon in the upper left corner
Illustration 26 Illustration 27
18
7.3 ADVANCED DEVICE CONFIGURATION
Please follow next steps in order to configure the device:
1. Select Device by location or Device by type option in the application’s main menu
2. Find the device you want to configure
3. Tap the device button and hold it until Device details dialog is opened (Illustration 28)
4. Each change you enter will be immediately applied to the both, device and gateway
Illustration 28
8. SCENE MANAGEMENT
One of the main features of Schwaiger client application is scene. Scene is specific event or set
of actions created by end user. Scenes can be triggered by one or more events/devices, which are
called triggers. The scene can also be set to send an email notification to the user’s email address
or push notification to the user’s smartphone.
By using Schwaiger mobile application the user is able to:
1. Create new scene
2. Run the scene
3. Edit the scene
4. Delete the scene
5. Disable the scene
8.1 CREATE NEW SCENE
Please follow next steps in order to create new scene:
1. Select Scenes option in the applications main menu
2. Tap the “Add scene” button in the upper right corner (Illustration 29)
3. To add a new trigger (or triggers) to the scene, tap the “Add” button in the upper right corner
and choose type of the trigger
19
Illustration 29
4. In case you would like to create device trigger (or triggers), please follow next steps:
a. In the device trigger dialog, choose the device you want to add as a trigger
b. In the drop down list, choose functionality and its value
c. In case you would like to set device delay time, choose an option and tap the “OK” button
to add the trigger (Illustration 30)
5. In case you would like to create time trigger (or triggers), please follow next steps:
a. In the time trigger dialog, choose the time when the scene should be active (Illustration 31)
b. Choose the schedule for the scene. In case of one-time event, set the desired date. In
case the event should repeat, choose the Weekly option button and the days when the
scene should occur
c. Tap the “OK” button to add the trigger
Illustration 30 Illustration 31
6. Repeat steps 3 to 5 and use logical operators AND/OR (upper right corner) to combine
multiple triggers (e.g. we would like to define an action “when light intensity is less than 20
AND motion is detected”)
7. Once you have set all triggers, tap the button to go to the next step
8. In the new dialog you will be able to set the status (or statuses) at which the scene will be
active. The status can be added by pressing “Add” button in the upper right corner ( Illustration
32). If you do not define any status, the scene will be active at all statuses
9. Once you have set all status(es), tap the button to go to the next step
10. In the new dialog you will be able to define an action (or action sets) for defined triggers. Upon
creation of an action set, you will be asked to define a name of the action set (Illustration 33)
20
Illustration32
11. For selected action set you will be able to add following actions by pressing “Add” button in
the upper right corner (Illustration 34):
a. Control device by location
b. Control device by type
c. Send email notification
d. Send push notification
e. Set the status
Illustration 33 Illustration 34
12. In addition to definition of an action set, you will be able to set delay time between actions sets exe-
cution. Delay time can be added by pressing “Delay” button in the upper left corner (Illustration 35).
13. By default, delay of 1 second is added after last created action set. By selecting delay control,
you can change delay time (Illustration 36)
Illustration 35 Illustration 36
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Schwaiger HA102 User manual

Category
Networking
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI