2. Futaba
  3. T32MZ
T32MZ

Futaba T32MZ User manual

  • Hello! I'm here to assist you with the Futaba GYA553 gyro and T32MZ transmitter setup manual I've reviewed. This document provides instructions on setting up the gyro, including connecting the devices, transferring settings, configuring mounting direction, servo parameters, and S.BUS assignments. I'm ready to answer your questions about these steps and features mentioned in the manual.
  • How do I connect the GYA553 to the T32MZ?
    What settings can be transferred between the T32MZ and GYA553?
    What is the AVCS mode in the gyro?
    How can I set the servo limits?
2
3
1
3
2
4
On the home screen, basic information such as gyro operation mode,
sensitivity, battery voltage are displayed.
Gyro operation mode / Gyro
gain
Displays "AVCS" or "Normal"
opera-tion mode and gyro
gain of aileron (roll), elevator
(pitch) and rudder (yaw) axis.
GYA553 Software version
Battery voltage
Displays the voltage of the
receiver battery connected to
GYA.
The software version of
the connected GYA553 is
displayed.
5
Set the mounting direction of GYA. Set mounting direction
ZLWKUHIHUHQFHWR¿JXUHEHORZ
Set with the wing type/tail type of GYA553. The wing type/tail type of the transmitter is not used and is normal.
7XUQR൵WKHHOHYRQ9WDLOPL[LQJRQWKHWUDQVPLWWHUVLGH
'RQRWXVHWUDQVPLWWHUVXEWULP$GMXVWXVLQJWKHJ\URQHXWUDOR൵VHW
:KHQXVLQJWKH6%86VHUYR\RXFDQDOVRXVHWKHQHXWUDOR൵VHWIXQFWLRQRIWKH6%86VHUYRVHWWLQJSDUDPHWHUV
6
Select the servo type according to the servo to be
used.
7KHVWDELOLW\RIGLJLWDOVHUYRPRGHRIDIOLJKW
LQFUHDVHVLQ RUGHUWR SHUIRUPD KLJKVSHHGFRQWURO
action.
Select the SB/R2 port.
7
Neutral position setting for each servo.
It is the direction settting of the gyro. Be careful as it will crash if the direction is reversed.
For dual aileron, dual elevator, and dual rudder aircraft, check the operating direction of each second
aileron/elevator/rudder.
8
This is the limit setting for each servo. The
SRVLWLRQRIWKHPD[LPXPRSHUDWLRQLVUHDGLQWRWKH
J\URLQWKH¿UVWVHWWLQJ
9
Reset each Config item. It returns to the initial
value.
The current rate numbers C1 to C5 are displayed by operating the channel of the transmitter.
/LNH WKH ÀLJKW FRQGLWLRQ IXQFWLRQ RI WKH WUDQVPLWWHU \RX FDQ VHW XS WR  GL൵HUHQW GDWD IRU WKH DWWLWXGH
KROGLQJIRUFHUDWHRIWKHDLUFUDIWLQ$9&6PRGHE\RSHUDWLQJWKHVZLWFKIURPWKHWUDQVPLWWHUDQGVZLWFK
between them. You can set the holding power rate selector switch to the channel with the AFR function of
the transmitter, and set the point for each rate on the AFR point curve to switch. It is also possible to use
WKHÀLJKWFRQGLWLRQIXQFWLRQWRZRUNZLWKWKHÀLJKWFRQGLWLRQVZLWFK
When set to SW of DG1 or DG2
Switch channel rate
Channel rate
When set to dial or lever
,WLVDIXQFWLRQWRDGMXVWWKHSRVWXUHKROGLQJIRUFHRIWKHDLUFUDIWLQ$9&6PRGH
Decreasing the value weakens the holding power and makes the operation feeling closer to the normal
mode.
10
The channel of each function can be changed.
Set the CH for each function according to the transmitter to be used. Any unused functions should be set
to INH (Inhibited).
/