Futaba GYA553 User manual

Brand: Futaba

Model: GYA553

Type: User manual

Futaba GYA553 is a high-performance 3-axis gyro system designed for use in aircraft models. It features AVCS (Attitude and Vector Control System) technology, which provides precise and stable control in all flight conditions. The GYA553 also has a built-in receiver, allowing it to be used with any compatible Futaba transmitter. Other features include a variety of adjustable parameters, such as gain, direction, and neutral offset, allowing you to fine-tune the gyro to your specific needs.

On the home screen, basic information such as gyro operation mode,

sensitivity, battery voltage are displayed.

Gyro operation mode / Gyro

gain

Displays "AVCS" or "Normal"

opera-tion mode and gyro

gain of aileron (roll), elevator

(pitch) and rudder (yaw) axis.

GYA553 Software version

Battery voltage

Displays the voltage of the

receiver battery connected to

GYA.

The software version of

the connected GYA553 is

displayed.

Set the mounting direction of GYA. Set mounting direction

ZLWKUHIHUHQFHWR¿JXUHEHORZ

Set with the wing type/tail type of GYA553. The wing type/tail type of the transmitter is not used and is normal.

7XUQR൵WKHHOHYRQ9WDLOPL[LQJRQWKHWUDQVPLWWHUVLGH

'RQRWXVHWUDQVPLWWHUVXEWULP$GMXVWXVLQJWKHJ\URQHXWUDOR൵VHW

:KHQXVLQJWKH6%86VHUYR\RXFDQDOVRXVHWKHQHXWUDOR൵VHWIXQFWLRQRIWKH6%86VHUYRVHWWLQJSDUDPHWHUV

Select the servo type according to the servo to be

used.

7KHVWDELOLW\RIGLJLWDOVHUYRPRGHRIDIOLJKW

LQFUHDVHVLQ RUGHUWR SHUIRUPD KLJKVSHHGFRQWURO

action.

Select the SB/R2 port.

Neutral position setting for each servo.

It is the direction settting of the gyro. Be careful as it will crash if the direction is reversed.

For dual aileron, dual elevator, and dual rudder aircraft, check the operating direction of each second

aileron/elevator/rudder.

If the SB/R2 port output is set to

"S.BUS(HS)" or "S.BUS(STD)", the

setting menu will display AIL3 and

AIL4 setting items.

* AIL3 and AIL4 settings cannot be

set with the button settings on the

GYA553 main unit.

* AIL3 and AIL4 settings cannot be set with the button

settings on the GYA553 main unit.

If the SB/R2 port output

is set to "S.BUS(HS)" or

"S.BUS(STD)", the setting

menu will display AIL3 and

AIL4 setting items.

This is the limit setting for each servo. The

SRVLWLRQRIWKHPD[LPXPRSHUDWLRQLVUHDGLQWRWKH

J\URLQWKH¿UVWVHWWLQJ

If the SB/R2 port output is set to "S.BUS(HS)"

or "S.BUS(STD)", the setting menu will display

AIL3 and AIL4 setting items.

* AIL3 and AIL4 settings cannot be set with the

button settings on the GYA553 main unit.

Reset each Config item. It returns to the initial

value.

The current rate numbers C1 to C5 are displayed by operating the channel of the transmitter.

/LNH WKH ÀLJKW FRQGLWLRQ IXQFWLRQ RI WKH WUDQVPLWWHU \RX FDQ VHW XS WR  GL൵HUHQW GDWD IRU WKH DWWLWXGH

KROGLQJIRUFHUDWHRIWKHDLUFUDIWLQ$9&6PRGHE\RSHUDWLQJWKHVZLWFKIURPWKHWUDQVPLWWHUDQGVZLWFK

between them. You can set the holding power rate selector switch to the channel with the AFR function of

the transmitter, and set the point for each rate on the AFR point curve to switch. It is also possible to use

WKHÀLJKWFRQGLWLRQIXQFWLRQWRZRUNZLWKWKHÀLJKWFRQGLWLRQVZLWFK

When set to SW of DG1 or DG2

Switch channel rate

Channel rate

,WLVDIXQFWLRQWRDGMXVWWKHSRVWXUHKROGLQJIRUFHRIWKHDLUFUDIWLQ$9&6PRGH

Decreasing the value weakens the holding power and makes the operation feeling closer to the normal

mode.

When set to dial or lever

The channel of each function can be changed.

Set the CH for each function according to the transmitter to be used. Any unused functions should be set

to INH (Inhibited).

CH setting items for AIL3 and AIL4 are displayed on the

¿QDOVFUHHQRIWKH6%86EDVLFVHWWLQJVFUHHQ%\VHWWLQJ

WKHRSHUDWLRQ&+RI$,/DQG$,/WKHJ\URFRQWUROOHG

signal is output to the corresponding CH of the S.BUS

output.

* Match the operation CH and CH setting on the function setting screen

on the transmitter side.

*When the AIL3 and AIL4 CH settings are INH, the gyro control is not

performed and the data sent from the transmitter is output as is.

Futaba GYA553 User manual

Futaba GYA553 User manual

Related papers