2. Futaba
  3. GYA553
GYA553

Futaba GYA553 User manual

  • Hello! I've analyzed the provided document, which is a user manual for the Futaba GYA553 gyro and T16IZ transmitter. It details how to connect the two devices, transfer settings, and configure the gyro's parameters including mounting direction, servo settings, and holding power. I'm ready to answer specific queries about the content and usage described in the manual.
  • How do I connect the GYA553 to the T16IZ?
    How do I transfer gyro settings from the T16IZ to the GYA553?
    What is the purpose of the Neutral offset setting?
    What is AVCS mode?
2
3
1
3
2
4
On the home screen, basic information such as gyro operation mode,
sensitivity, battery voltage are displayed.
Gyro operation mode / Gyro
gain
Displays "AVCS" or "Normal"
opera-tion mode and gyro
gain of aileron (roll), elevator
(pitch) and rudder (yaw) axis.
GYA553 Software version
Battery voltage
Displays the voltage of the
receiver battery connected to
GYA.
The software version of
the connected GYA553 is
displayed.
5
Set the mounting direction of GYA. Set mounting direction
ZLWKUHIHUHQFHWR¿JXUHEHORZ
Set with the wing type/tail type of GYA553. The wing type/tail type of the transmitter is not used and is normal.
7XUQR൵WKHHOHYRQ9WDLOPL[LQJRQWKHWUDQVPLWWHUVLGH
'RQRWXVHWUDQVPLWWHUVXEWULP$GMXVWXVLQJWKHJ\URQHXWUDOR൵VHW
:KHQXVLQJWKH6%86VHUYR\RXFDQDOVRXVHWKHQHXWUDOR൵VHWIXQFWLRQRIWKH6%86VHUYRVHWWLQJSDUDPHWHUV
6
Select the servo type according to the servo to be
used.
7KHVWDELOLW\RIGLJLWDOVHUYRPRGHRIDIOLJKW
LQFUHDVHVLQ RUGHUWR SHUIRUPD KLJKVSHHGFRQWURO
action.
Select the SB/R2 port.
7
Neutral position setting for each servo.
It is the direction settting of the gyro. Be careful as it will crash if the direction is reversed.
For dual aileron, dual elevator, and dual rudder aircraft, check the operating direction of each second
aileron/elevator/rudder.
8
This is the limit setting for each servo. The
SRVLWLRQRIWKHPD[LPXPRSHUDWLRQLVUHDGLQWRWKH
J\URLQWKH¿UVWVHWWLQJ
9
Reset each Config item. It returns to the initial
value.
The current rate numbers C1 to C5 are displayed by operating the channel of the transmitter.
/LNH WKH ÀLJKW FRQGLWLRQ IXQFWLRQ RI WKH WUDQVPLWWHU \RX FDQ VHW XS WR  GL൵HUHQW GDWD IRU WKH DWWLWXGH
KROGLQJIRUFHUDWHRIWKHDLUFUDIWLQ$9&6PRGHE\RSHUDWLQJWKHVZLWFKIURPWKHWUDQVPLWWHUDQGVZLWFK
between them. You can set the holding power rate selector switch to the channel with the AFR function of
the transmitter, and set the point for each rate on the AFR point curve to switch. It is also possible to use
WKHÀLJKWFRQGLWLRQIXQFWLRQWRZRUNZLWKWKHÀLJKWFRQGLWLRQVZLWFK
When set to SW of DG1 or DG2
Switch channel rate
Channel rate
,WLVDIXQFWLRQWRDGMXVWWKHSRVWXUHKROGLQJIRUFHRIWKHDLUFUDIWLQ$9&6PRGH
Decreasing the value weakens the holding power and makes the operation feeling closer to the normal
mode.
When set to dial or lever
10
The channel of each function can be changed.
Set the CH for each function according to the transmitter to be used. Any unused functions should be set
to INH (Inhibited).
/