Frame Construction Ceiling Installation
1
Take the cutout template from the packaging box and
punch out along the larger perforated circle. Place the
cutout template against the ceiling and trace along the inside
circle. Carefully cut out the ceiling material along the circle.
3
Cut material.
SI 3CT LP
Ceiling Speaker
a. Remove the top terminal cover (see the illlustration in
step 3f) by loosening (do not remove) both top screws,
sliding the top terminal cover away from the screws, and
removing the cover, as shown here.
68-1263-01 Rev. B
09 07
User’s Guide
2
The side terminal cover, as illustrated in step 3f, must first
be removed before wiring the speaker.
Loosen the single top screw of the side terminal cover and
pull the side terminal cover straight out. See the illustration
below.
Side View of Input Terminal
Top Terminal
Cover
Loosen
screw.
Loosen
two screws.
c. Insert the conduit(s) into the knockout opening(s) and
secure the conduit to the cover with the locking nut.
d. Pull the speaker wires from the conduit, strip 0.2” (5 mm)
from the wire ends (do not tin the wires), and secure the
wires into the 4-pole captive screw connector. To connect
speakers in parallel, see the wiring diagram below.
e. Bring the speaker up to the bottom of the hole in the
ceiling.
f. Plug the wired connector from step 3d into the speaker’s
audio input connector. Secure the top terminal cover
with the two top screws that were loosened in step 3a;
hook the side terminal cover to the top terminal cover; and
secure the side terminal cover in place with the screw that
was loosened in step 2.
1
Power Amplifier
Speaker 1 Speaker 2 Speaker 3
70 V To Speakers
Trace template.
Top Terminal
Cover
Side Terminal
Cover
Side Terminal
Cover
4-pole Captive
Screw Connector
N Installation in a plenum-rated environment
requires a wire gauge of 14 AWG to 18 AWG.
See NOTE below.
b. Remove the knockout(s) from the top terminal cover
depending on the direction from which the conduit(s) will
be entering the cover.
Front View of Input Terminal
4-pole Captive
Screw Connector
LOOP IN LOOP
IN
33-1351-01
Rev. B
SI 3CT LP
Ceiling Speaker
User’s Guide
5
Connect a secondary support line from the seismic tab to a
secure support point, as shown below.
Set the rotary tap selector (shown above) to the proper
position.
CAUTION
Do not turn the tap selector to the 8 Ω position
when using 70 V / 100 V lines.
Install the speaker grille.
2
4
Loosen the four screws on the front baffle (counter
clockwise) 1/2 turn. Insert the speaker in the ceiling hole,
then tighten the screws (clockwise) until the dog legs clamp
the speaker to the ceiling. See the following illustration.
Do not overtighten screws.
CAUTION
Remove the ceiling tile where the speaker is to be installed.
Loosen the four screws on the front baffle (counter
clockwise) 1/2 turn. Then tighten the screws (clockwise)
until the dog legs clamp the speaker to the ceiling.
1
Cut the hole in the tile (see step 1 on page 1).
2
8
Set the rotary tap selector and install the grille (see step 5 of
Frame Construction Ceiling Installation on this page).
5
Connect the wires to the speaker terminal connector (see
step 3 on page 1).
3
Bring the speaker cable through the hole of the cut tile,
then reinstall the tile.
4
Remove the adjacent tile. Place 2 V-rails and 1 C-ring
across the tile where speaker is to be installed. Bring the
speaker up to the bottom of the hole in the ceiling tile.
6
Do not overtighten screws.
CAUTION
7
Connect a secondary support line from the seismic tab to
a secure support point (see step 5 of Frame Construction
Ceiling Installation on this page).
V-rail
C-ring
Suspended Ceiling InstallationFrame Construction Ceiling Installation,
cont’d
Apply 4 pieces of
black putty (supplied),
equally spaced 90° apart,
to the upper inside edge
of the grille.
Seismic Tab &
Support Line
Adjusting the Tap Selector.
70 Volt
100 Volt
Painting the Speaker Baffle
Tear along the smaller perforated line of the cutout
template marked as a paint shield. Push it into the front
baffle of the speaker. Paint the front. Remove the paint
shield after the paint has dried.
Application diagram
POWER
12V
3A MAX
OUTPUTS
4/8 Ohms
INPUTS
70V
COM 70V
REMOTE
(MONO)
(MONO)
L
R
10V
LISTED
1T23
I.T.E.
VOL/MUTE
L
MPA 181T
R
C
US
PC
Projector
DVD/VCR Combo
VGA w/
Audio Cable
Composite
Audio RCA
Variable
Extron
VCM 100 AAP
Volume/Mute Controller
Extron
MPA 181T
Mini Power Amplifier
Extron
SI 3CT LP
Low Profile Ceiling
Speakers
VOLUME
VCM 100
MUTE
SI 3CT LP
Ceiling Speaker
User’s Guide
Packaging
3
Specifications
Acoustic & Electrical
General
Speaker type................................. Low profile ceiling speaker with metal back can
Frequency response..................... 75 Hz to 18 kHz, -10 dB, half space
Power capacity.............................. 16 W continuous pink noise
32 W continuous program
Nominal sensitivity........................ 83 dB, 1 W, 1 m, 16 W tap, half space
Nominal coverage angle............... 170° conical coverage
Nominal impedance ..................... 8 ohms
Rotary switch taps........................ 70V: 16 W, 8 W, 4 W, 2 W, 1 W
100V: 16 W, 8 W, 4 W, 2 W
Driver............................................ 3” (76 mm) full range paper cone with moisture
resistant coating
Input/output connector.................. (1) 5 mm captive screw connector, 4-pole for input
and loop-through
Package ....................................... 2 speakers (1 pair)
Temperature/humidity.................... Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Mounting....................................... Ceiling mountable with included hardware: V-rails for
2’ x 4’ (600 mm x 1200 mm) ceiling tiles, and C-rings
Enclosure type.............................. Formed steel back can; high impact, fire-resistant
(UL94V-0), polystyrene plastic baffle/rim
Enclosure outer dimensions.......... 4.0” H x 9.9” diameter (102 mm x 251 mm diameter)
Cutout dimensions........................ 8.82” diameter (224 mm diameter)
Product weight.............................. 6 lbs (2.72 kg) each speaker
Shipping weight............................. 22 lbs (9.98 kg) per pair w/ mounting kit package
Listings ......................................... UL 2043, UL1480
Compliances ................................ CE, NFPA90, NFPA70A
Warranty ....................................... 5 years parts and labor
NOTE: All nominal levels are at ±10%.
NOTE: Specifications are subject to change without notice.
V-rails (4)
Mounting Screws
& Putty
C-rings
Speakers
Speaker Grilles
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
www.extron.com
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron SI 26X User manual
-
-
-
Extron electronics V-LockTM User manual
-
Extron electronics CS 120P User manual
-
Extron electronics SF 3C LP User manual
-
-
-
-
Extron electronics SF 3C LP User manual
Other documents
-
SPEEDI-GRILLE TB-PAB 10 Operating instructions
-
Extron electronics SI 28 User manual
-
Extron electronic SI 28 User manual
-
QSC AD-C1200 User manual
-
-
Extron electronics 305SA User manual
-
Community DS8 Owner's manual
-
Electro-Voice EVID Ceiling Speaker Systems Installation guide
-
Mackie SP400C User manual
-
