Extron SI 26X User manual

Category
Soundbar speakers
Type
User manual

Extron SI 26X ceiling speakers are high-quality audio devices designed for professional installations in commercial and residential settings. These speakers are characterized by their ability to deliver clear and natural sound in a wide range of applications, including background music, paging, and sound reinforcement. The SI 26X is a 2-way, open back ceiling speaker with a frequency range of 50 Hz to 20 kHz and a nominal impedance of 8 ohms. It features a 6.5-inch (165 mm) polypropylene cone woofer with moisture resistant coating and a 0.75-inch (19 mm) titanium dome tweeter. The SI 26X has a nominal sensitivity of 89 dB and a nominal coverage of 110 degrees. It can handle up to 50 watts of continuous program power and 25 watts of continuous pink noise power.

Extron SI 26X ceiling speakers are high-quality audio devices designed for professional installations in commercial and residential settings. These speakers are characterized by their ability to deliver clear and natural sound in a wide range of applications, including background music, paging, and sound reinforcement. The SI 26X is a 2-way, open back ceiling speaker with a frequency range of 50 Hz to 20 kHz and a nominal impedance of 8 ohms. It features a 6.5-inch (165 mm) polypropylene cone woofer with moisture resistant coating and a 0.75-inch (19 mm) titanium dome tweeter. The SI 26X has a nominal sensitivity of 89 dB and a nominal coverage of 110 degrees. It can handle up to 50 watts of continuous program power and 25 watts of continuous pink noise power.

Frame Construction Ceiling Installation
1
Take the cutout template from the packaging box and
punch out the larger perforated circle. Place the cutout
template against the ceiling and trace the inside of the
circle. Carefully cut out the ceiling material around the
circle.
4
Insert the speaker through the bottom of the hole in
the ceiling.
5
6
Loosen the four screws on the front baffle
(counterclockwise) ½ turn. Then tighten the screws
(clockwise) until the dog legs clamp the speaker to
the ceiling.
Do not over tighten screws.
Install the speaker grill.
Specifications:
Packaging
3
Bring the speaker cable through the hole in the ceiling
and connect the leads to the speaker’s spring terminal
clips.
2
Remove the grill from the speaker.
CAUTION
Trace template.
Red (+)
Black (-)
Cut Material
Apply 4 pieces (supplied) of
black putty to the edge of
the grill.
User’s Guide
Cutout Template
68-1166-01 Rev. B
04 06
Acoustic & Electrical
General
Speaker type.................................. 2-way, open back ceiling speaker
Frequency range........................... 50 Hz to 20 kHz, -10 dB, half space
Power capacity.............................. 50 W continuous program,
25 W continuous pink noise
Nominal sensitivity...................... 89 dB, 1 W, 1 m, half space
Nominal impedance .................... 8 ohms
Crossover frequency................... 3 kHz
Nominal coverage........................ 110°
Woofer........................................... 6.5" (165 mm) polypropylene cone
with moisture resistant coating
Tweeter.......................................... 0.75" (19 mm) titanium dome
Temperature/humidity................... Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Warranty ....................................... 5 years parts and labor
NOTE All nominal levels are at ±10%.
NOTE Specifications are subject to change without notice.
SI 26X
Ceiling Speaker
User’s Guide
Suspended Ceiling Installation
Remove the ceiling tile where the speaker is to be installed.
An optional ceiling mount kit (Part # 70-533-01)
needs to be purchased separately. Each kit
has the hardware to mount 2 speakers.
Painting the Speaker Baffle
Tear along the smaller perforated line of the cutout
template, marked as paint guard. Push the paint guard
into the front baffle of the speaker. Paint the front.
Remove the paint guard after the paint has dried.
1
Cut the hole in the tile. See step 1 of the frame construction
ceiling section on the reverse side of this sheet.
2
V-rail
C-ring
8
Apply 4 pieces (supplied) of black putty (see the reverse
side of this sheet). Install the speaker grille.
6
Connect the wires to the speaker terminal clips (as in step 3
on the reverse side of this sheet).
Application diagram:
3
Remove the grill from the speaker.
4
Bring the speaker cable through the hole of the cut tile,
then reinstall the tile.
5
Remove the adjacent tile. Place 2 V-rails and 1 C-ring
across the tile where the speaker is to be installed. Insert
the speaker through the bottom of the hole in the ceiling tile.
7
Do not over-tighten screws!
CAUTION
NOTE
Extron
SI 26X
Two-way Ceiling
Speakers
POWER
OUTPUTS
4/8 Ohms
INPUTS
L
R
L
R
REMOTE
10V
VOL/MUTE
L
MPA 122
R
C
US
PC
DVD
Projector
VCR
VGA w/
Audio Cable
S-video
Audio RCA
Composite
Audio RCA
Variable
Audio
Output
Extron
VCM 100 AAP
Volume/Mute Controller
Extron
MPA 122
Mini Power Amplifier
MUTE
VOLUME
VCM 100 AAP
SI 26X
Ceiling Speaker
User’s Guide
Loosen the four screws on the front baffle
(counterclockwise) ½ turn. Then tighten the screws
(clockwise) until the dog legs clamp the speaker to
the ceiling.
  • Page 1 1
  • Page 2 2

Extron SI 26X User manual

Category
Soundbar speakers
Type
User manual

Extron SI 26X ceiling speakers are high-quality audio devices designed for professional installations in commercial and residential settings. These speakers are characterized by their ability to deliver clear and natural sound in a wide range of applications, including background music, paging, and sound reinforcement. The SI 26X is a 2-way, open back ceiling speaker with a frequency range of 50 Hz to 20 kHz and a nominal impedance of 8 ohms. It features a 6.5-inch (165 mm) polypropylene cone woofer with moisture resistant coating and a 0.75-inch (19 mm) titanium dome tweeter. The SI 26X has a nominal sensitivity of 89 dB and a nominal coverage of 110 degrees. It can handle up to 50 watts of continuous program power and 25 watts of continuous pink noise power.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI