2easy DK4781 Quick Manual

DK4761 & DK4781

2 WIRE INTERCOM SYSTEM

Please read this manual carefully before using the product you purchase, and keep it well for future use.We reserve the right to

modify the specication in this manual at any time without notice.

RF CARDRF CARD

Quick Guide

-1-

1. Product Lists Of Kits

Kit DK4761 consists of：

1* Outdoor Station- DMR11S/ID/D6

1* Surface Box- RH-MR11

6* Indoor Units- DT47MG-W

2* Four Outputs Controller- DT-DBC4A1

1* Power Supply with UL approved- DR-30-24

1* Power Separator- DT-DPS

1* DIN Rail

1* Relay- DS-ERL

1* AWG18 Power Cable

2* Management Cards- Add Card & Delete Card

12* Proximity Cards

Kit DK4781 consists of：

1* Outdoor Station- DMR11S/ID/D8

1* Surface Box- RH-MR11

8* Indoor Units- DT47MG-W

2* Four Outputs Controller- DT-DBC4A1

1* Power Supply with UL approved- DR-30-24

1* Power Separator- DT-DPS

1* DIN Rail

1* Relay- DS-ERL

1* AWG18 Power Cable

2* Management Cards- Add Card & Delete Card

16* Proximity Cards

-2-

2. System Connection

In-out wiring without any distributor

Code=1, DIP-6=off

Code=31, DIP-6=off

Code=32, DIP-6=on

Code=2, DIP-6=off

ID=00

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1

3+-

A

4

B

4

1 2 3 4 5 6

ON

4

5

2

RF CARD

DPSDR-30-24

Cable Usage A B

Twisted cable 2x0.00116 sq.in 196ft 196ft

Twisted cable 2x0.00155 sq.in 262ft 262ft

Cable Usage A B

Twisted cable 2x0.00155 sq.in 229ft 98ft

Twisted cable 2x0.00233 sq.in 229ft 164ft

When Monitor quantity < 20

When Monitor quantity > 20

[1]: Door Station, when there is only one Door Station,

the DIP bit-1 and bit-2 should be set to 00.

[2]: Power Supply(DR-30-24), MUST be installed side

by side with the DPS unit.

[3]: Power Separator, MUST be installed side by side

with the DR-30-24 unit.

[4]: Monitor, each one with a unique User Code (Max.32

Monitors), the bit-6 of the DIP should be set to 0 (off) if

the Monitor is not at the end of the bus line.

[5]: Monitor, the bit-6 of the DIP should be set to 1 (on)

if the Monitor is connected at the and of the bus line.

Note: The thicker the copper wire is, the longer distances

will be. Best wire to use is 18 Gauge twisted, while Cat 5

or 6 are not recommended.

-3-

Star wiring with 4 output distributor DBC4A1

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

1 2 3 4 5 6

ON

Code=32, DIP-6=on

Code=30, DIP-6=on

Code=31, DIP-6=on

Code=29, DIP-6=on

Code=4, DIP-6=on

Code=2, DIP-6=on

Code=3, DIP-6=on

Code=1, DIP-6=on

ID=00

1 2 3 4 5 6

ON

A

C

B

1

3+-2

4 4

6

5

4 4

OFF ON

DBC4A1

A B C D

DBC4A1

A B C D

Impedance

switch

Impedance

switch

RF CARD

DPSDR-30-24

[1]: Door Station, when there is only one Door

Station, the DIP bit-1 and bit-2 should be set

to 00.

[2]: Power Supply(DR-30-24), MUST be

installed side by side with DPS unit.

[3]: Power Separator, MUST be installed side

by side with the DR-30-24 unit.

[4]: Monitor, each one with a unique User

Code, note that all the bit-6 of the DIP should

be set to 1 (on) in this case.(Max.32 Monitors)

[5]: 4 output distributor DBC4A1,Impedance

switch of all DBC4A1 should be set to OFF,

except the last DBC4A should be set to ON.

(When there is only 1 DBC4A1, should set to

ON).

Note: The thicker the copper wire is, the longer distances will

be. Best wire to use is 18 Guage twisted, while Cat 5 or 6 are not

recommended.

Cable Usage A B C

Twisted cable 2x0.00116 sq.in 196ft 196ft 98ft

Twisted cable 2x0.00155 sq.in 262ft 262ft 131ft

Cable Usage A B C

Twisted cable 2x0.00155 sq.in 229ft 98ft 65ft

Twisted cable 2x0.00233 sq.in 229ft 164ft 98ft

When Monitor quantity < 20

When Monitor quantity > 20

-4-

3. Parts and Functions

[1]

[7]

[2]

[3]

[4]

[5]

[6]

[8]

[9]

[10]

SD card

1 2 3 4 5 6

ON DIP

Key functions

NO. Item Description

[1] Digital LCD touch screen See the next page for details

Display the visitors' image

[2] Emergency button Press it & hold for 3s to send SOS message to mo-

bile phone,the function is supported by GSM unit.

[3] Message indicator Light up when the monitor has missed call

[4] Unlock button Press to release the door

[5] Talk/Mon button Press to communicate hands free with visitor

Press to view the outdoor condition in standby mode

[6] Microphone Transmit audio from one station to other stations

[7] SD card slot Use to insert micro-SD card

[8] Mounting hook Use to hang up the monitor

[9] Speaker Send out sounds of ring tones,audios and alarms

[10] Connection port Bus terminal

-5-

Terminal description

1 2 3 4 5 6

ON DIP

L2

L1

DIP Switches

SW+

SW-

RING

GND

NC

1 2 3 4 5 6

ON DIP

L1,L2: Bus line terminal.

SW+,SW-: Extra door bell call button connection port.

Ring,GND: Extra buzzer connection port.

NC: Undened.

DIP switches: Total 6 bits can be congured.

• Bit1~Bit5: User Code setting.

• Bit6: Set to ON if the monitor is at the end of the line or works with DBC4A.

Otherwise, set to OFF.

-6-

L1 L2

1 2 3 4 5 6

ON DIP

12.13 inch

4.84 inch

10.91 inch

12.28 inch

4.17 inch

5.04 inch

RF CARD

Camera Lens

Speaker

Night View LED

ID Card Window

Status Indicator

Microphone

Nameplate

LED Indicator

Call button

Mounting box for

flush mounted

Rainy cover for

surface mounted

Connection

port

A B

Note:Key A and key B will not be seen on the panel,they are cryptic.About activating key

A and key B, please refer to Part 5.

4. Terminal Description For Outdoor Station

• +12V: 12VDC power output.

• LK-: Power ground. See page 13 for hook-up with DS-ERL included in kit.

• LK+: Common contact of the relay.

• NO.: Normally open contact of the relay

• EB+: Exit button positive connection port.

• EB-: Exit button negative connection port.

• JP-LK: For electronic lock safety type setting(refer to door lock connections).

• SET : DIP switches for system configurations. By default, DIP5 is on, that

means the unlocking time is 5 seconds.

• CN/KMB: Call button module connection port.

• CN/T-COIL: Reserved.

• CN/FUN: Touch sensor keypad module or TFT display module connection

port.

• CN/WGN: Card reader module connection port.

• Bus(L1,L2): Non-polarity bus line,connect to power supply.

CN-LK

JP-LK

+12V

LK-

LK+

NO

EB-

EB+

SET

12V

TX1

RX1

GND

RX3

TX3

GND

5CL

GND

5DA

RST

INT

GND

12V

CLK

DAT

STR

C2

C1

CTR

GND

VIO

POW

WG0

WG1

GND

12V

CN/KMB CN/T-COIL

CN/FUN CN/WGN

L1 L2

1 2 3 4 5 6

ON DIP

-7-

ON(1)

=

OFF(0)

=

ON

123456

Bit denition Bit state Function Descriptions

Bit-1 and Bit-2

(door station ID setting)

1 2 3 4 5 6

ON

Default setting, ID = 0, setting for the rst door station

1 2 3 4 5 6

ON

ID = 1, setting for the second door station

1 2 3 4 5 6

ON

ID = 2, setting for the third door station

1 2 3 4 5 6

ON

ID = 3, setting for the fourth door station

Bit-3

(single or double row

button setting)

1 2 34 5 6

ON

Default setting ,set "OFF " when using a double row button door

station

1 2 34 5 6

ON

Set "ON" when using a single row button door station

Bit-4

(button code select)

12345 6

ON

Default setting, set "OFF " when using the default codes of the

button

12345 6

ON

Set " ON " when using the programmed codes of the button.

Bit-5

(unlock time quick setting)

1 2 3 4 56

ON

Unlocking time = 1second. (can be changed by door station or

software)

1 2 3 4 56

ON

Default setting, unlocking time = 5 seconds.

Bit-6

(cryptic key setting)

1 2 3 4 5 6

ON

Default setting, normally key A and key B is not useful(about the

position of key A and key B,please refer to part 2)

1 2 3 4 5 6

ON

Activating the key A and key B is allowed.

Totally 6 bits can be congured by dip-switch. All

switches can be modified either before or after

installation, please restarting the power whenever

the switches have been modied.

5. DIP Switches Settings Of Outdoor Station

-8-

6. Indoor Unit Parameter Setting

How to enter the installation setting page

How to know the machine code

• On main menu page, touch [Logo] icon to enter About page.

• When the screen stay in About page,press UNLOCK button on front panel and

hold for 2 seconds.

• A keypad is shown.

Refer to the followings:

00:10 DS-1

About

Local Address 00.00

Video Standard AUTO

System Verson 00.01.00

Display Driver 1.0

Font 1.0

UI 1.0

INSTALLER SETUP 123

_

? + OK: Help Menu

@ + OK: Address Setting Menu

Input the key “? and ok” to open Help instructions menu.

Refer to the followings:

Help 01/04

2412:Reset to Default Setting

2499:Format Memory

2810:MCU Code Update

2811:TFT,UI Code Update

2812:Consumer Tune Update

2813:Format SD Card

INSTALLER SETUP 123

_

? + OK: Help Menu

@ + OK: Address Setting Menu

-9-

DIP Switches Settings Of Indoor Unit

TheDIPswitchesareusedtosettheusercodeforeachmonitor.Total6bitscanbecong-

ured.

• Bit-1 to Bit-5 are used for user code setting. The value range is from 1 to 32, which have 32

different codes for 32 apartments.

• When multi monitors need to be installed in one apartment, these monitors should use the

same user code, and the master/slave mode should be set on the monitor.

• Bit-6 is bus line terminal switch, which should be set to “ON” if the monitor is at the end of

bus line, otherwise be set to “OFF”.

ON(1)

=

OFF(0)

=

ON

ON DIP

123456

Bit state Setting Bit state Setting

1 2 3 4 5

6

ON DIP

1 2 3 4 5

6

ON DIP

When monitor is not

at the end of bus line.

When monitor is at

the end of bus line.

Bit-6 switch setting

-10-

In the case of double row buttons:

• DIP3 switch set to off

1 2 34 5 6

ON

RF CARD

07 08

05 06

03 04

01 02

RF CARD

08

06

04

02

In the case of single row buttons:

• DIP3 switch set to off

1 2 34 5 6

ON

RF CARD

04

03

02

01

• DIP3 switch set to on

1 2 34 5 6

ON

7. Call codes

The door station automatically assigns the call codes to the connected module’s buttons.

Regardless of the structure of the call button module, the button numbers are listed from

the top to bottom and from left to right (in the case of double row buttons):

-11-

9. Electric Lock Connection(NOT RECOMMENDED). See Page 12.

1) Door Lock Controlled with Internal Power

1. The door lock is limited to 12Vdc, and holding

current must be less than 250mA when using internal

power supply mode.

2. The Unlock Mode Parameter must be set to 0 (by

default).

3. Jumper set to 1-2 position for power-off-to-unlock

safety type(Normally closed mode); set to 2-3 po-

sition for power-on-to -unlock type(Normally open

mode ).

4. If different unlocking time is needed,change the

unlock time on door station,detail information refer to

DT system technical guide .

Note: NOT RECOMMENDED unless the door lock is less than 250mA. Please see Page 12

for HOW TO HOOK UP A DOOR RELEASE.

JP_LK

12V 300mA

Exit button

Jumper position in 2-3

+

-+12V

LK -

LK+

N.O.

EB-

EB+

123

Power-on-to-Unlock type:

8. Answering a call

When there is a call from a video door station.The call tone sounds, an image will be

displayed on the screen.

Touch icon on screen or press TALK/MON button on the panel, begin

communicating hands free with the visitor for 90 seconds.

While communicating with the visitor, unlock the door, capture images/videos and adjust

screen&volume are available. More details,please refer to the following descriptions.

Note: 1.If nobody answers the phone, the screen will be turned off automatically after 40 seconds.

2.The 5 direction pad operation should make in effect with sh-eye door station.

-12-

10. Specication

2) Door Lock Controlled with External

Power

1. The external power supply must be used

according to the lock.

2. The jumper must be taken off before

connecting.

3. Setup the Unlock Mode Parameter for

different lock types

• Power-on-to-unlock type:Unlock

Mode=0(by default)

• Power-off-to-unlock type:Unlock

Mode=1

4. If different unlocking time is needed,

change the unlock time on door station,de-

tail information refer to DT system techni-

cal guide .

Power-on-to-Unlock type:

12V 300mA

Jumper position in 1-2

+12V

LK -

LK+

N.O.

EB-

EB+

+

-

JP_LK

123

Exit button

Power-off-to-Unlock type: Power-off-to-Unlock type:

+

-

+12V

LK - (GND)

LK+(COM)

N.O.

EB-

EB+

Take off the Jumper

JP_LK

Cut off the line

123

Exit button

+12V

LK - (GND)

LK+(COM)

N.O.

EB-

EB+

Take off the Jumper

+

-

JP_LK

Cut off the line

123

Exit button

Power supply: 26Vdc

Power Consumption Of Outdoor Station:

1W in standby;

5W in working.

Power Consumption Of Indoor Unit:

0.29W in standby;

7W in working.

Unlock Power output: 12Vdc,250mA

Unlock timing: 1~99s

Working temperature: - 20ºC ~ +55ºC

Wiring: 2 wire, non-polarity

Dimension:

5.2(H)×8.9(W)×0.71(D) inch(Indoor Unit)

12.32(H)×5.04(W)×2.48(D)inch(ush)

12.32(H)×5.04(W)×2.76(D) inch(surface)

-13-

Power supply: 26Vdc

Power Consumption Of Outdoor Station:

1W in standby;

5W in working.

Power Consumption Of Indoor Unit:

0.29W in standby;

7W in working.

Unlock Power output: 12Vdc,250mA

Unlock timing: 1~99s

Working temperature: - 20ºC ~ +55ºC

Wiring: 2 wire, non-polarity

Dimension:

5.2(H)×8.9(W)×0.71(D) inch(Indoor Unit)

12.32(H)×5.04(W)×2.48(D)inch(ush)

12.32(H)×5.04(W)×2.76(D) inch(surface)

11. Hooking up a door release

-14-

Note

manual are preserved.

DK4761 & DK4781

FOR TECHNICAL SUPPORT CALL

1516-387-6606 FROM 9AM TILL 4PM

MONDAY THRU FRIDAY

OUR WEBSITE WWW.NYWINT.COM

2easy DK4781 Quick Manual

This manual is also suitable for

2easy DK4781 Quick Manual

Related papers

Other documents