Anova BH1894T Installation guide

Anova
Brand
Anova
Model
BH1894T
Type
Installation guide

This manual is also suitable for

Hammer Drill
(4) SS or Rubber Washers
90107A127 OR 90130A050
Masonry Drill Bit Set
3/16" & 3/8"
3/8" Drop-in Anchor
Setting Tool
Hammer
Pencil
Allen Wrench Set
7/32"
Wire Brush
Level
Safety Glasses
(4) 3/8" Drop-in Anchors
97083A310
(4) 3/8”-16 x 1” SS
Button Head Cap Screw
92949A624
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
SECTION A-A
4X FOOT MOUNT
SECTION B-B
SCALE 0.08 : 1
AA
B B
1
1
2
2
3
3
4
4
A A
B B
THIRD ANGLE PROJECTION
TOLERANCES UNLESS NOTED:
X 1 X.X .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX .015625 ANGULAR ± 1°
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
DRAWN
Beacon Hill 6" Contour Bench
SIZE
BBH1880B_SPEC-REV-A01
DATE
4/2/2014 SCALE
.09375:1 SHEET
DWG NO
TITLE
B. MENDEZ
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
REV
1 OF
A01
1
REV DESCRIPTION ECN TR.# DATE
001 ORIGINAL PRINT NONE 4/2/14
A00 RELEASE TO PRODUCTION NONE 01/27/15
A01 ADDED VIEW B-B NONE 10/29/18
NOTES:
34.49"
24.72"
77.43"
18.83"
28.11"
23.87"
.50"
2.50"
72.75"
76.25"
71.08"
3.25"
73.75"
21.87"
.50"
(4 PLCS)
LENGTH
WIDTH
Ø.50"
(4 PLCS)
Beacon Hill
Beacon Hill Benches
FOOT MOUNT SIZE CHART
SKU # LENGTH WIDTH
BH1880T
BH1880R
PL2480
73.75" 21.87"
BH1890T
BH1890R
PL2490
73.75" 21.71"
BH1884T
BH1884R
49.75" 21.87"
BH1894T
BH1894R
49.75" 21.71"
11/12/2018 Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
6.
7.
8.
Place bench in the desired location. Mark the location of the holes with a
pencil. To verify the alignment of the anchor markings you may reference the
bottom of page 1.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 3/16" diameter drill bit followed by the 3/8" diameter bit.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Use the 3/8" drop-in anchor setting tool and hammer to x the anchor into
the drilled hole by inserting the narrow end of the tool into the anchor and
giving it several hammer blows.
Insert one 3/8" drop-in anchor into the hole and use a hammer to tap the
anchor ush with the concrete.
Repeat steps 2 - 5 until all anchors are installed.
Align the mounting holes of the bench over top of the anchors.
Care should be given to avoid rubbing the powder coating o the foot.
A 3/8" rubber washer is a suitable replacement option. Mount the bench
to the anchors by fastening a button head cap screw and washer into each
anchor. Leave the hardware nger tight until all of them have been installed.
Verify that the bench is level before tightening the anchors. Tighten all of the
hardware with a 7/32" Allen wrench.
!
!
5
42
5 7
8.28.1
Beacon Hill Benches
  • Page 1 1
  • Page 2 2

Anova BH1894T Installation guide

Anova
Brand
Anova
Model
BH1894T
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents