Anova THMC6 Installation guide

Anova
Brand
Anova
Model
THMC6
Type
Installation guide

This manual is also suitable for

Hammer DrillHammer
Pencil
Wire Brush
Level
Safety Glasses
(4) 3/8" Drop-in Anchors
97083A310
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED: HARDWARE NEEDED:
Installation Instructions
Step-by-Step Installation Sequence
!
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the bench or table.
CAUTION: Oversized holes and holes drilled to deep in the concrete will make it dicult to set the anchor.
Allen Wrench Set
7/32"
Masonry Drill Bit Set
1/4" & 1/2"
3/8" Drop-in Anchor
Setting Tool
(4) 3/8" SS or Rubber
Washers
90107A127 OR 90130A050
(4) 3/8”-16 x 1-1/8” SS
Button Head Cap Screw
92949A867
Madison Benches and Tables
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
6.
7.
8.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
Repeat steps 2 - 5 until all anchors are installed.
!
!
5
42
Align the mounting holes of the bench or table over top of the anchors.
Care should be given to avoid rubbing the powder coating o the foot.
A 3/8" rubber washer is a suitable replacement option. Mount the bench or
table to the anchors by fastening a button head cap screw and washer into
each anchor. Leave the hardware nger tight until all of them have been
installed. Verify that the bench or table is level before tightening the anchors.
Tighten all of the hardware with a 7/32" Allen wrench.
Use the 3/8" drop-in anchor setting tool and hammer to x the anchor into
the drilled hole by inserting the narrow end of the tool into the anchor and
giving it several hammer blows.
Insert one 3/8" drop-in anchor into the hole and use a hammer to tap the
anchor ush with the concrete.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with 1/4" diameter drill bit followed by the 1/2" diameter bit.
Place bench or table in the desired location. Mark the location of the holes
with a pencil. To verify the alignment of the anchor markings you may
reference page 3.
Madison Benches and Tables
5 7
8.28.1
Copyright 2019 ANOVA® Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
FOOT MOUNTS:
10/29/2018
Madison Benches and Tables
SE
CTION A-A
SCALE 1/12
A A
1
1
2
2
3
3
4
4
A A
B B
1
A01
6 Ft Flat Bench
OF
RCPMC6_SPEC-REV-A01
1
REV
SHEET
1:12
SCALE
DATE
10/25/2011
DWG NO
TITLE
B
DRAWN
C.O'HARA II
SIZE
THIS DRAWING AND ALL ITS INCLUDED
INFORMATION IS THE PROPERTY OF
LANDSCAPE BRANDS. DO NOT USE OR
COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS
SUBJECT TO RETURN ON DEMAND.
ALL DIMENSIONS ARE IN INCHES
AND ALL ANGLES OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
PRINT IS FOR FABRICATION
ONLY. SURFACES MAY PICK
UP .093
.0625 OF COATING.
TOLERANCES UNLESS NOTED:
X.XX ± .25 X.XXX ± .125 X.XXXX ± .0625
X.XXXXX ± .03125 ANGULAR ± 1
DO NOT SCALE DRAWING
211 N. Lindbergh Blvd.
St. Louis, MO
63141-7809
888-535-5005
www.landscapebrands.com
REV DESCRIPTION ECN TR.# DATE
A00 ORIGINAL PART, RELEASE TO
PRODUCTION NONE 05/10/12
A01 ADDED FOOT MOUNT VIEW NONE 10/18/18
NOTES:
72.25" 79.25"
71.25"
27.57"
35.11"
3.50"
1.50"
15.50"
15.50"
25.57"
68.75"
.50"
(4 PLCS)
SECTION A-A
SCALE .09375
A A
1
1
2
2
3
3
4
4
A A
B B
1
A00
6 Ft Flat Bench
OF
RCPMF6_SPEC-REV-A01
1
REV
SHEET
.09375:1
SCALE
DATE
10/25/2011
DWG NO
TITLE
B
DRAWN C.O'HARA II
SIZE
THIS DRAWING AND ALL ITS INCLUDED
INFORMATION IS THE PROPERTY OF
LANDSCAPE BRANDS. DO NOT USE OR
COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS
SUBJECT TO RETURN ON DEMAND.
ALL DIMENSIONS ARE IN INCHES
AND ALL ANGLES OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
PRINT IS FOR FABRICATION
ONLY. SURFACES MAY PICK
UP .093
.0625 OF COATING.
TOLERANCES UNLESS NOTED:
X.XX ± .25 X.XXX ± .125 X.XXXX ± .0625
X.XXXXX ± .03125 ANGULAR ± 1
DO NOT SCALE DRAWING
211 N. Lindbergh Blvd.
St. Louis, MO
63141-7809
888-535-5005
www.landscapebrands.com
REV DESCRIPTION ECN TR.# DATE
A00 ORIGINAL PART, RELEASE TO
PRODUCTION NONE 05/10/12
A01 ADDED FOOT MOUNT NONE 10/19/18
NOTES:
72.25"
18.50"
71.25"
19.86"
3.50"
1.50"
15.50"
18.11"
67.75"
.50"
SECTION A-A
SCALE 1:12
A A
1
1
2
2
3
3
4
4
A A
B B
1
A00
Coffee Table
OF
RCPMT4_SPEC-REV-A01
1
REV
SHEET
.09375:1
SCALE
DATE
6/6/2012
DWG NO
TITLE
B
DRAWN
C.O'HARA II
SIZE
THIS DRAWING AND ALL ITS INCLUDED
INFORMATION IS THE PROPERTY OF
LANDSCAPE BRANDS. DO NOT USE OR
COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS
SUBJECT TO RETURN ON DEMAND.
ALL DIMENSIONS ARE IN INCHES
AND ALL ANGLES OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
PRINT IS FOR FABRICATION
ONLY. SURFACES MAY PICK
UP .093
.0625 OF COATING.
TOLERANCES UNLESS NOTED:
X.XX ± .25 X.XXX ± .125 X.XXXX ± .0625
X.XXXXX ± .03125 ANGULAR ± 1
DO NOT SCALE DRAWING
211 N. Lindbergh Blvd.
St. Louis, MO
63141-7809
888-535-5005
www.landscapebrands.com
REV DESCRIPTION ECN TR.# DATE
A00 ORIGINAL PART, RELEASE TO
PRODUCTION NONE 06/06/12
A01 ADDED FOOT MOUNT VIEW NONE 10/26/18
NOTES:
47.50"
51.86"
3.50"
1.50" 18.50"
48.25"
47.25"
50.11"
43.75"
.50"
(4 PLCS)
RCPMT4 & THMT4
RCPMF6 & THMF6
RCPMC6 & THMC6
Ø.50"
(4 PLCS)
Ø.50"
(4 PLCS)
Ø.50"
(4 PLCS)
67.75"
68.75"
50.11"
43.75"
18.11"
25.57"
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova THMC6 Installation guide

Anova
Brand
Anova
Model
THMC6
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents