Dell W-AP105 Installation guide

Dell
Brand
Dell
Model
W-AP105
Type
Installation guide

This manual is also suitable for

AP-105 Mounting Kit
Installation Guide
0510651-02 | July 2010 1
Introduction
The AP-105 Wall Mounting kit provides two options, with built-in security features, for mounting your
AP-105 to a wall. Use the Box Mount Bracket to install the AP over wall box and use the Wall Mount
Bracket to install the AP directly on a wall.
The kit includes the following:
z 1x plastic Box Mount Bracket
z 1x plastic Wall Mount Bracket
Figure 1 AP-105-MNT
Figure 2 AP-105-MNT-DC
Required Tools
z A screwdriver that matches the screws used for mounting your brackets.
z An M5 (Metric) or 3/16" (Standard) hex key.
NOTE
This installation guide pertains to both the AP-105-MNT and AP-105-MNT-DC. The AP-105-MNT can only be
used with an AP that is powered by Power Over Ethernet (PoE), while the AP-105-MNT-DC allows the use of a
DC power source.
AP105_008
Box Mount Bracket Wall Mount Bracket
AP105_008
Wall Mount Bracket
Box Mount Bracket
2 AP-105 Mounting Kit | Installation Guide
Installation
1. Before securing your mount to a double-gang box or directly to the wall, route the ethernet cable
through the openings show in Figure 3.
Figure 3 Cable Routing
2. Install your mounting bracket.
For the Wall Mount Bracket (Figure 4):
a. Before installing your Wall Mount Bracket, install the appropriate wall anchors. Screws and wall
anchors are not included.
b. Align the screw holes in the mount with the holes or anchors on the wall.
c. Insert the screws and tighten them to secure your Wall Mount Bracket.
Figure 4 Wall Mount Bracket Installation
For the Box Mount Bracket:
a. Align the screw holes in the mount with the those in the gang box, as shown in Figure 5.
b. Insert the screws and tighten them to secure your Box Mount Bracket.
AP105_010
Box Mount Bracket
Cable Route
to ENET Port
Cable from
Gang Box
Wall Mount Bracket
AP105_012
NOTE
If you plan to permanently connect a serial console cable to the AP installed over a gang-box, you must use the
Wall Mount Bracket instead of the Box Mount Bracket. This provides the necessary space behind the AP to run
both cables.
AP-105 Mounting Kit | Installation Guide 3
The box mount bracket can also be installed over a double-gang wall box. Use the same steps as above
to install it over a double-gang wall box, however the installation requires a third screw. For more
details, see Figure 6.
Figure 5 Box Mount Bracket Installation (Single-gang Box)
Figure 6 Box Mount Bracket Installation (Double-gang Box)
AP105_011
AP105_011
4 AP-105 Mounting Kit | Installation Guide
3. Connect the ethernet cable to the ethernet port (ENET) on the back of the AP.
4. Secure the AP to the mounting bracket by aligning the mounting holes on the back the AP with the
mounting post on the bracket.
5. Push the AP against the posts and downward until the posts engage the slots at the top of the mounting
holes. See Figure 7 and Figure 8 for more details.
Figure 7 Completing the Installation (Wall Mount Bracket)
Figure 8 Completing the Installation (Box Mount Bracket)
Figure 9 Completed Installation
AP105_015
AP105_014
AP105_009
AP in Box Mount Bracket AP in Wall Mount Bracket
AP-105 Mounting Kit | Installation Guide 5
6. To remove the AP from the mounting bracket, begin by inserting an M5 or 3/16" hex key into the hole
shown in Figure 10.
7. Use the hex key to depress the tab on the AP and push the AP up, releasing the AP from the
mounting post on the bracket.
Figure 10 Removing the AP
AP105_013
6 July 2010 | 0510651-02
© 2010 Aruba Networks, Inc. All rights reserved.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Dell W-AP105 Installation guide

Dell
Brand
Dell
Model
W-AP105
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents