Triton Systems Argo User manual

Anti-Skim Card Reader

Upgrade Manual

TDN 07103-00273 Rev. A

Corporate Headquarters:

21405 B Street

Long Beach, MS 39560

Phone: (800) 259-6672

Fax: (228) 868-9445

COPYRIGHT NOTICE

trademark of Triton Systems of Delaware, LLC

Document Updates

June 9, 2016......................Rev. A..................Original 1031018

Table of Contents

EMV Anti-Skim card Reader Kits .......................................................................................................................ii

Section 1 - ARGO 7.................................................................................................................................................1-1

Section 2 - ARGO 12...............................................................................................................................................2-1

Section 3 - ARGO 15...............................................................................................................................................3-1

Section 4 - RL16XX.................................................................................................................................................4-1

Section 5 - RL23XX.................................................................................................................................................5-1

Section 6 - RL53XX.................................................................................................................................................6-1

ALL ABOVE UNITS

Section 7 - Upgrade From ICM 330 Card Reader..............................................................................................7-1

ALL ABOVE UNITS

Section 8 - Calibration and Diagnostics..............................................................................................................8-1

i

WARNING:

When the new Anti-Skim card Reader is installed, be sure to use the screws pro-

vided in the kit. DO NOT reuse the screws from the old card reader; this will

cause damage to the metal inserts on the new card reader.

 e new Anti-Skim Card reader will need to be calibrated a er it is installed. Be

sure to refer to the Con guration and Diagnostics section.

Minimum so ware requirement to support the ICM33B Anti-Skim Card Reader

is 4.0.0.33

Improper grounding may

cause damage to ATM

and/or components.

*Please contact Sales@Triton.com for model availability.

Kit

06200-00355

Anti-Skim EMV Card Reader Upgrade kit for, RL16, RL23, RL53, and ARGO. Not for use

when upgrading from 330.

Tools Required Small Phillips head Screwdriver, Side Cut Pliers

Parts Supplied

Description Quantity

1 Card Reader w/Bezel | EMV | ICM33B Anti-Skim 1

2 Serial Card Reader Comms Ribbon Cable | X2 1

3 Screw | 6-32 Phillips Machine Screw | Pan Head | 3/8” long | Zinc Plated with Nylon Patch 5

4 Mounting bracket, angled, one 6-32 threaded hole, one 0.165” open hole, 0.062” thick

steel, tin plate

1

5 Screw | #6-32 | 1/4 Inch | Pan Phil Head w/Ext Tooth Wash 1

6 Triton EMV Kernel Label 1

7 Screw | #8-32 | 3/8 inch | Pan Phil Head w/Ext Tooth Wash 1

1

2

3

4

5

6

ii

7

Kit

06200-00358

Anti-Skim EMV Card Reader Upgrade kit. For upgrading from 330 only. ARGO, RL16,

RL23, RL53.

Tools Required Small Phillips head Screwdriver

Parts Supplied

Description Quantity

1 Card Reader w/Bezel | EMV | ICM33B Anti-Skim 1

2 Screw | 6-32 Phillips Machine Screw | Pan Head | 3/8” long | Zinc Plated with Nylon Patch 5

1

2

iii

SECTION 1

ANTI-SKIM CARD READER

UPGRADE

ARGO 7

KIT 06200-00355

ARGO 7

1-2

1. Carefully remove the plastic cover from the main board.

2. Unplug the Card Reader Communication Cable from the main board. Remove the cable from the cable clips.

ARGO 7 NOTE: For the ARGO 7 installation, not all parts included in the kit are required.

Before starting the installation process, remove power from the ATM by entering Management Functions > Sys-

tem Parameters > Shut Down the Terminal > Enter. When prompted, open the control panel and turn power

switch to o (O) position. Disconnect main power cable from the power supply.

Anti-Skim Card Reader Upgrade

1-3

3. Remove the card reader by removing the four screws shown below. DISCARD CARD READER SCREWS.

If ground wire is attached, remove the screw securing wire.

4. Obtain the Anti-Skim Card Reader from kit number 06200-00355 (see page ii for details). Install the card

reader by inserting it through the front of the control panel. Ensure Triton logo on the Bezel is in the position

shown. (See  gure A). Secure the card reader with the four 3/8” screws provided. (See  gure B).

CAUTION: Be sure to use the screws provided in the kit. DO NOT reuse the screws from step 3; this will cause

damage to the metal inserts on the new card reader.

Figure A

Figure B

I-65Track 1-2

ARGO 7

1-4

5

. Obtain the Card Reader Communication Ribbon Cable from the kit and plug the cable into the card reader.

Fasten the cable securely by pushing in the two tabs on the connector. (See  gure C). Connect the other end of

the Communication Cable to the main board as shown. (See  gure D).

6. Route the Communication Cable through the Cable Clips as shown.

Figure C

Figure D

Anti-Skim Card Reader Upgrade

1-5

7. Secure the ground wire from the card reader to the display bracket with one #8-32 X 3/8 inch Pan Phil Head

w/Ext Tooth Wash screw from kit as shown.

8. Obtain the main board cover (removed during step 1) and secure it to the top of the main board.

9. Connect the main power cable to the power supply and power on the ATM. Close the control panel. REFER

TO SECTION 8 FOR INSTRUCTIONS ON CALIBRATION AND DIAGNOSTICS OF THE ANTISKIM

CARD READER.

SECTION 2

ANTI-SKIM CARD READER

UPGRADE

ARGO 12

KIT 06200-00355

ARGO 12

2-2

1. Unplug the Card Reader Communication Cable from the docking board. Remove the cable from the cable

clips.

2. Remove the card reader by removing the four screws shown below. DISCARD CARD READER SCREWS.

If ground wire is attached, remove the screw securing wire.

ARGO 12 NOTE: For the ARGO 12 installation, not all parts included in the kit are required.

Before starting the installation process, remove power from the ATM by entering Management Functions > Sys-

tem Parameters > Shut Down the Terminal > Enter. When prompted, open the control panel and turn power

switch to o (O) position. Disconnect main power cable from the power supply.

I-65Track 1-2

Anti-Skim Card Reader Upgrade

2-3

3. Obtain the Anti-Skim Card Reader from kit number 06200-00355 (see page ii for details). Install the card

reader by inserting it through the front of the control panel. Ensure Triton logo on the Bezel is in the position

shown. (See  gure A).

4. Secure the card reader with the four 3/8” screws provided. (See  gure B).

CAUTION: Be sure to use the screws provided in the kit. DO NOT reuse the screws from step 2; this will cause

damage to the metal inserts on the new card reader.

Figure A

Figure B

ARGO 12

2-4

5. Obtain the Card Reader Communication Ribbon Cable from the kit and plug the cable into the card reader.

Fasten the cable securely by pushing in the two tabs on the connector. (See  gure C). Connect the other end of

the Communication Cable to the docking board as shown. (See  gure D).

6. Route the Communication Cable through the cable clips as shown.

Figure D

Figure C

Anti-Skim Card Reader Upgrade

2-5

7. Secure the ground wire from the card reader to the display bracket with one #8-32 X 3/8 inch Pan Phil Head

w/Ext Tooth Wash screw from kit as shown.

8. Connect the main power cable to the power supply and power on the ATM. Close the control panel. REFER

TO SECTION 8 FOR INSTRUCTIONS ON CALIBRATION AND DIAGNOSTICS OF THE ANTISKIM

CARD READER.

SECTION 3

ANTI-SKIM CARD READER

UPGRADE

ARGO 15

KIT 06200-00355

ARGO 15

3-2

1. Carefully remove the plastic cover from the main board.

2. Unplug the Card Reader Communication Cable from the main board. Remove the cable from the cable clips.

ARGO 15 NOTE: For the ARGO 15 installation, not all parts included in the kit are required.

Before starting the installation process, remove power from the ATM by entering Management Functions > Sys-

tem Parameters > Shut Down the Terminal > Enter. When prompted, open the control panel and turn power

switch to o (O) position. Disconnect main power cable from the power supply.

Anti-Skim Card Reader Upgrade

3-3

3. Remove the card reader by removing the four screws shown below. DISCARD CARD READER SCREWS.

If ground wire is attached, remove the screw securing wire.

4. Obtain the Anti-Skim Card Reader from kit number 06200-00355 (see page ii for details). Install the card

reader by inserting it through the front of the control panel. Ensure Triton logo on the Bezel is in the position

shown. (See  gure A). Secure the card reader with the four 3/8” screws provided. (See  gure B).

CAUTION: Be sure to use the screws provided in the kit. DO NOT reuse the screws from step 3; this will cause

damage to the metal inserts on the new card reader.

Figure A Figure B

I-65Track 1-2

ARGO 15

3-4

5. Obtain the Card Reader Communication Ribbon Cable from the kit and plug the cable into the card reader.

Fasten the cable securely by pushing in the two tabs on the connector. (See  gure C). Connect the other end of

the Communication Cable to the main board as shown. (See  gure D).

6. Route the Communication Cable through the cable clips as shown.

Figure C

Figure D

Anti-Skim Card Reader Upgrade

3-5

7. Secure the ground wire from the card reader to the display bracket with one #8-32 X 3/8 inch Pan Phil Head

w/Ext Tooth Wash screw from kit as shown.

8. Obtain the main board cover (removed during step 1) and secure it to the top of the main board.

9. Connect the main power cable to the power supply and power on the ATM. Close the control panel. REFER

TO SECTION 8 FOR INSTRUCTIONS ON CALIBRATION AND DIAGNOSTICS OF THE ANTISKIM

CARD READER.

SECTION 4

ANTI-SKIM CARD READER

UPGRADE

RL16XX

KIT 06200-00355

Page is loading ...

Triton Systems Argo User manual

Triton Systems Argo User manual

Related papers

Other documents