TROVE T1RM3CK1 Installation guide

Brand: TROVE

Model: T1RM3CK1

Type: Installation guide

TROVE T1RM3CK1 is a pre-assembled rack kit designed to accommodate one Intelligent Dual Reader Controller and one Dual Reader Interface Module, providing access control and power distribution capabilities. It features a fully assembled enclosure with a backplane, power supply/charger, fused access power controller, dual input fused power distribution module, voltage regulator, and wire harnesses. The kit is suitable for four-door applications and offers various output options, including fail-safe/fail-secure or dry form "C" outputs, with configurable current limits.

T1RM3CK1

4 Door Kit with Fused Outputs

Accommodates one (1) Intelligent Dual Reader Controller and

one (1) Dual Reader Interface Module.

Fully assembled kit includes:

- Trove1R rack enclosure with TM1R Altronix/Mercury backplane

- One (1) eFlow6NB - Power Supply/Charger

- One (1) ACM4 - Fused Access Power Controller

- One (1) PDS8 - Dual Input Fused Power Distribution Module

- One (1) VR6 - Voltage Regulator

- Wire harnesses and management

T1RM3CK1D

4 Door Kit with PTC Outputs

Accommodates one (1) Intelligent Dual Reader Controller and

one (1) Dual Reader Interface Module.

Fully assembled kit includes:

- Trove1R rack enclosure with TM1R Altronix/Mercury backplane

- One (1) eFlow6NB - Power Supply/Charger

- One (1) ACM4CB - PTC Access Power Controller

- One (1) PDS8CB - Dual Input PTC Power Distribution Module

- One (1) VR6 - Voltage Regulator

- Wire harnesses and management

Access & Power Integration

Rev. 072423

Installing Company: _________________________ Service Rep. Name: __________________________________________

Address: _________________________________________________________ Phone #: _________________________

All registered trademarks are property of their respective owners. More than just power.™

Installation Guide

Altronix/Mercury Wired Rack Kits

Models Include:

All components of these Trove kits are UL Listed sub-assemblies.

Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

- 2 - T1RM3CK1(D) Series Installation Guide

Overview:

Altronix Trove Mercury wired rack kits are pre-assembled and consist of Trove rack enclosure/backplane with factory installed Altronix power

supply/charger and sub-assemblies. They also accommodate a variety of Mercury modules for up to four doors in a single enclosure.

Configuration Chart:

Altronix

Model Number

120VAC 60Hz

P/S Input Current (A)

Power Supply Board

Input Fuse Rating

Power Supply Board

Battery Fuse Rating

Nominal DC

Output Voltage

Maximum Supply

Current for Main and Aux.

Outputs on

Power Supply board,

PDS8(CB) Power

Distribution Module and

ACM4(CB) Access Power

Controller’s outputs (A)

Current Per

ACM4(CB) Output (A)

ACM4(CB) Board

Input Fuse Rating

ACM4(CB) Board

Output Fuse (PTC)

Rating

Fail-Safe/Fail-Secure

or Dry Form “C”

Outputs

PDS8(CB) Board

Input Fuse (PTC)

Rating

PDS8(CB) Board

Output Fuse (PTC)

Rating

[DC] [Aux]

24VDC

Output

Range

(V)

24VDC

Output

Range

(V)

T1RM3CK1

3.5 5A/

250V

10A/

32V

20.28-

26.4

20.28-

26.4 24VDC @ 5.6A

2.5 10A/

250V

3A/

32V 410A/

32V

3A/

32V

T1RM3CK1D 2.0 10A/

250V 2.5A 4 9A 2.5A

Installation Instructions for T1RM3CK1(D):

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.

These products are for indoor use only and must be installed within the protected premises.

Note: First assemble and Install Z Bracket Wire Management Accesory

(refer to Z Bracket Installation pg. 3)

1. Remove backplane from enclosure prior to installing into rack cabinet (do not discard hardware).

2. In order to mount included UL Listed tamper switch (Altronix Model TS112 or equivalent) turn the

enclosure upside down. Punch out the knockout in designated location, on the back of the unit,

from outside of the drawer (Fig. 1, pg. 2). Insert the tamper switch into the knockout from outside of the

drawer with the button facing outwards and spaded connectors inside the drawer.

Connect tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device.

To activate alarm signal open the rack drawer.

3. Slide the rack enclosure into an open 2U location in the four post rack cabinet.

4. Utilizing proper fasteners attach front ears to the rack rails.

5. Attach the rear of the adjustable slides to the rear rails of the rack cabinet with the proper fasteners.

6. Secure the rack cover (Fig. 2a, pg. 2) and rack drawer to earth ground (Fig. 2b, pg. 2).

7. Make sure that all internal cofigurations (wiring, voltage selection, switch settings, etc.) are complete before mounting backplane back

into enclosure.

8. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow6NB and corresponding sub-assembly Installation Guides for the

following models: ACM4(CB), PDS8(CB), VR6 for further instructions.

Fig. 1

Back of the drawer,

viewed from outside.

Tamper Switch

mounting location

Fig. 2

Fig. 2a

Fig. 2b

T1RM3CK1(D) Series Installation Guide - 3 -

Assembling and Attaching Z Bracket Wire Management Accessory (included):

Altronix Trove Rack enclosures include Z Bracket, a convenient and reliable wire management accessory.

Hardware (included):

Ten (10) bolts and eight (8) lock nuts.

1. Carefully unpack Z Bracket. Do not discard hardware

(included) (Fig. 3, pg. 3).

2. Attach arms to each other using bolts and

lock nuts (Fig. 3a, pg. 3).

3. Attach the hinge brackets to the ends of

arms using bolts and nuts positioning

them as shown on (Fig. 3b, pg. 3).

4. Make sure that all nuts are tightened.

5. Attach the hinge bracket on the longer side of Z Bracket to the adjustable slide using bolts and lock nuts (included) (Fig. 4, 4a, pg. 3).

6. Attach the hinge bracket on the shorter side of Z Bracket to the rear of the rack enclosure using bolts (included).

Fig. 4

Fig. 4a

Fig. 3b

Two (2)

Fig. 3

Fig. 3a

- 4 - T1RM3CK1(D) Series Installation Guide

T1RM3CK1(D): Configuration of Mercury Boards:

1. Position access controller module over corresponding spacers and depress onto snap on spacers (Fig. 5, pg. 4).

2. Mount backplane to enclosure with hardware.

Access Controller Position Chart for the Following Models:

LenelS2 / Mercury Access Controller Pem Mounting

LNL-2220 / LP1502 A

LNL-1320 / MR52 B

Fig. 5

To LED lense

To IEC connector

D1 D2

IN1IN2 IN3IN4 IN5IN6 IN7IN8

IN9

GND

IN10

INPUTS

IN-5V

OUT-12V

RDR POWER

REG UNREG

GNDDAT CLK BZRLED V0CLKGNDDAT BZRLED V0

READER 1READER 2

REV

TR+

TR-

R+

R-

GND

ACDC

RS-485 12V

J5,J6

TERMINATOR

2W 4W

RS-485

NO CNCNOC NC

RLY 1RLY 2RLY 3RLY 4

NO CNCNOC NC

RLY 5RLY 6

NO CNCNOC NC

65432

OFF ON

MADE IN USA

READER INTERFACE

U10

COM

COM K3

COM K5

COM K2

COM K4

COM K6

TMP

FLT

RESET

BT1

3V BR/CR2330

3.3V

VBAT

IN1

K2 K1

K3K4

IN2

IN3

IN4

IN5

IN6

IN7

IN8

PASS 12V

GND

DAT

TB8

READER 1

BZR

GND

FLT

GND

TMP

GND

VIN

TB1

LED

CLK

READER 2

LED

BZR

GND

CLK

DAT

TB9

OUT 1 C

OUT 2 C

OUT 4 C

OUT 3 C

TB10TB11

RXD

CTS

GND

RTS

TXD

TB2

TB3

TR+

GND

TR-

IN1

IN2

IN3

IN4

IN5

IN6

IN7

IN8

TB4

TB5

TB6

TB7

Altronix

Power Supply

NC C NO NC C NO

AC FAIL BAT FAIL

TRIGGER

AC DCAC1

EOL NO GND

SUPERVISED RESET

+AUX-

- BAT +- DC +

L G N

OFF - 24V

ON - 12V

Altronix VR6

is mounted

below PDS8(CB)

+ INP1 --

PWR1 +OFF

IN1

IN2

PWR1 +

PWR2 +

COM (--- )

+ INP2 --

IN1 Fuse

Common Power Outputs (NEG)

OUT1 OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

1 2 3 4 5 6 7 8

Altronix PDS8(CB)

TRG

TRIGGER

INPUT

LED1 LED2 LED3 LED4

MAIN

OUTPUT 1

NC C NO COM NC C NO COM NC C NO COM NC C NO COM

OUTPUT 2 OUTPUT 3

IN GND

OUTPUT 4

-- +

CONTROL

-- +

POWER

+INP- T +RET-

INTERFACE

NO C NC

FACP

Altronix ACM4(CB)

(A) LNL-2220

(B) LNL-1320

Snap On

Spacer

Mercury Board

Backplane

Pem

Fig. 5a

T1RM3CK1(D) Series Installation Guide - 5 -

Notes:

- 6 - T1RM3CK1(D) Series Installation Guide

Notes:

T1RM3CK1(D) Series Installation Guide - 7 -

Notes:

- 8 - T1RM3CK1(D) Series Installation Guide

Trove1R Enclosure Dimensions (H x W x D approximate):

3.375” x 19.0” x 26.5” (85.8mm x 482.6mm x 673.1mm). Shown with Z Bracket attached

0.1”

2.5mm

1.5”

38.1mm

11.175” (283.8mm)

Tamper

Switch

3/4” Conduit

1” Conduit

Conduit

3/4”

1/2”

2.4”

61mm

4.57”

116.1mm

3.375”

85.8mm

26.5”

673.1mm

19” (482.6mm)

R 1.27” (32.3mm)

1” (25.4mm)

0.55” (14mm)

3.62”

92mm

Altronix is not responsible for any typographical errors. Product specifications are subject to change without notice.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056

website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty

IIT1RM3CK1(D) G24W MEMBER