Maxxima MEL-9185W Installation guide

Brand
Maxxima
Model
MEL-9185W
Type
Installation guide

Maxxima MEL-9185W is a stylish addition to any outdoor space. This wall light is easy to install and can be mounted on any wall surface. It features a durable construction that can withstand the elements and provides a bright, warm light. The adjustable machine screws on the upper crossbar allow you to customize the length of the fixture to fit your specific needs. With its three-year warranty, you can be sure that this light will provide years of reliable use.

Maxxima MEL-9185W is a stylish addition to any outdoor space. This wall light is easy to install and can be mounted on any wall surface. It features a durable construction that can withstand the elements and provides a bright, warm light. The adjustable machine screws on the upper crossbar allow you to customize the length of the fixture to fit your specific needs. With its three-year warranty, you can be sure that this light will provide years of reliable use.

Outdoor Wall Light Installation Guide MEL-9185W
www.maxximastyle.com
If you are replacing an exisitng fixture, remove and disconnect
the old fixture first.
1. Expose the supply wires from the outlet box.
2. Position the supply wires with the white supply wire on one
side of the outlet box and the black supply wire on the other side.
3. Thread the fixture mounting screws through the mounting bracket
as shown in the illustration.
4. Attach the mounting bracket to the outlet box by allowing the outlet
box screws to pass through the large slots in the mounting bracket.
5. Connect the outlet box ground wire to the mounting bracket with
the green hex-head ground screw by screwing it into the
tapped hole in the mounting bracket marked “GND”.
6. Connect the fixture ground wire to the outlet box ground wire
by using a wire connector.
7. Connect the white wire from the fixture assembly to the white
supply wire from the post using a wire connector.
8. Connect the black wire from the fixture assembly to the black
supply wire from the post using a wire connector.
Note: Strip 1-1/2” of insulation from the outlet box ground wire
(if insulated). Allow the stripped end to extend an extra 1” from the
ground screw to enable a connection to the fixture ground wire
using a wire connector.
WIRING INSTRUCTIONS
FIXTURE MOUNTING INSTRUCTIONS
GND
Outlet Box
Ground Wire
Outlet Box
Wire Connectors
White Supply
Wire
Fixture Mounting
Plate
White
Fixture
Wire
Mounting
Bracket
Outlet Box
Screw
Fixture
Ground
Wire
Green
Ground
Screw
Fixture
Ground
Wire
Wire
Connector
Outlet Box
Ground Wire
Black
Fixture
Wire
Outlet Box
Screw
Wire
Connector
Black
Supply
Wire
Fixture
Mounting
Screws
1. After all connections are secure, carefully tuck the wires into the electrical outlet
box. No loose strands or loose connections should be present.
2A. Attach the fixture mounting plate to the fixture mounting screws on the mounting
bracket. Make sure no wires are pinched or exposed. Tighten the cap screws or
ball nuts to hold the fixture securly in place.
2B. The (Qty. 2) machine screws on the upper crossbar can be adjusted by
loosening their nuts (not seen in the figures above) and then screwing them in or out
to alter the length of machine screws sticking out from the upper crossbar.
Once the adjustment appears correct, lock the machine screws in place with their
nuts and then secure the fixture tightly against the wall by using the (Qty. 2) cap nuts.
3. To prevent moisture from entering the outlet box and the fixtures mounting plate
causing a short, apply a bead of clear caulk to outline the outside of the fixtures
mounting plate where it meets the wall. Leave a small space at the bottom to allow
any condensation or moisture to escape.
4. The installation is now complete. Install the bulb and restore the electricity, check
the operation of your lighting fixture.
CAULK
Caulk Line
Outlet Box Fixture
Fixture
Mounting
Screws
Fixture
Mounting
Plate Cap Screws
or Ball Nuts
[email protected] 866-MAXXIMA (629-9462) www.maxximastyle.com 125 Cabot Court Hauppauge, NY 11788
THREE YEAR WARRANTY
Maxxima extends a 3 year limited fixture and bulb warranty to the original purchase that the products listed are free from defects in material
and/or workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of
defects due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original
installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume
any obligation whatsoever beyond sending a free replacement product.
•Risk of electric shock - Disconnect power at the source
before installation.
•If you are unsure about the installation or the maintenance
of the wall light, please consult an electrician.
•Do not make or alter any holes in the wiring enclosure or
modify any electrical componentry.
CAUTIONS
•To insure personal safety, proper grounding of the
electrical fixture is required.
•The fixture must be wired in accordance with the National
Electric Code and applicable local codes or ordinances.
WARNINGS
  • Page 1 1

Maxxima MEL-9185W Installation guide

Brand
Maxxima
Model
MEL-9185W
Type
Installation guide

Maxxima MEL-9185W is a stylish addition to any outdoor space. This wall light is easy to install and can be mounted on any wall surface. It features a durable construction that can withstand the elements and provides a bright, warm light. The adjustable machine screws on the upper crossbar allow you to customize the length of the fixture to fit your specific needs. With its three-year warranty, you can be sure that this light will provide years of reliable use.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents