GFW Lancaster 2 Drawer Console Table User manual

Size : (W)970 x (D)350 x (H)760 mm

970

760

Thank you for purchasing the CONSOLE HALL TABLE.

Please read the instructions carefully to ensure safe operation of the product.

350

Batchh No : PO# 2759

Page 1 of 16

LANCASTER - CONSOLE HALL TABLE ASSEMBLY INSTRUCTIONS

Page 2 of 16

This product is intended for a maximum weight of 15kgs and drawer load capacity 4kg each.

Do not exceed this weight.

Due to the size of this product we recommend that is assembled in the room intended for use.

When you ready to start, make sure that you have the right tools, plenty of space and a clean, dry area for

assembly

Unwrap all packaging materials and place the components on top of the carton box or not on a clean floor to

prevent it from scratching.

Check the pack and make sure you have all the parts listed.

Ensure that this product is fully assembled as illustrated before use.

Check all screws or bolts are tightened and inspect regularly.

This product should only be used on firm, level ground.

Keep small parts out of reach of children.

Make sure the legs remain in contact with the ground.

Tools not included.

DO NOT use power tools to construct this product.

DO NOT tighten screw until fully assembled.

DO NOT over tighten screw or bolts.

DO NOT use this product if parts are missing, damage or worn.

DO NOT stand or sit on this table.

We recommend the use of the wall strap provided for safety reasons. N.B. Wall fixings are not included -please

source suitable fixings for your wall type. If in doubt please consult a qualified tradeperson. Warning: Always

ensure the area to be drilled is free from hidden electrical wires, water and gas pipes.

It is essential that this unit is fixed to a wall with the fixings provided.

Never use scourers, abrasives or chemical cleaners.

To clean wipe with a sponge and soapy water. Do not use solvent based cleaners or detergents as they

can bleach or damage the product.

Side Panel (L) (30) x 320 x 735mm)A 1

BSide Panel (R) (30) x 320 x 735mm) 1

CTop Panel (25 x 350 x 370mm) 1

DBottom Panel (30) x 318 x 880mm) 1

EBack Panel ( 15 x 160 x 880mm) 1

FCentre Panel ( 15 x 295 x 140mm) 1

GFront panel Bar (15 x 80 x 880mm) 1

MDrawer Back (15 x 100 x 337mm)

HRear panel Bar (15 x 80 x 880mm) 1

IBottom Panel Bar (15 x 60 x 880mm) 1

J

K

Drawer Front (15 x 160 x 587mm) 2

Drawer Side (L) (15 x 100 x 250mm) 2

LDrawer Side (r) (15 x 100 x 250mm) 2

2

ZDrawer Bottom (3 x 244 x 386mm) 2

A

H

G

EF

B

C

I

D

J

K

L

M

Z

Page 3 of 16

5

3

2x

l

Poket Handle

(64hole mm)

4x

j

Drawer Slide

(250 mm)

4x

k

Drawer Slide

(250 mm)

1x

m

Allen Key

M4

5x

a

Unitar Screw

D6.3 x 40mm

8x

b

CSK Screw

M4.7 x 38mm

21x

c

Wooden Dowel

D8 x 30mm

9x

f

Csk Screw

M3.5 x 15mm

2x

e

Handle Screw

M6 x 1/2mm

22x

d

Minifix Bolt

M5 x 29mm

5x

g

Nail Leg

5 x 8 x 13.5mm

22x

h

Minifix Cam

D15 x 12mm

8x

i

Euro Screw

D6 x 9mm

Page 4 of 16

1x

o

Safety strap

(L-200 mm)

1x

n

Wall Plug

STEP 1

21 x

c

Parts Required Qty

Panel (A) 1

Panel (B) 1

Panel (D) 1

Panel (E ) 1

Parts Required Qty

Panel (F ) 1

Panel (G) 1

Panel (H) 1

Panel (I ) 1

Parts Required Qty

Panel (K) 2

Panel (L) 2

A

c

B

D

IE

F

c

K

L

H

G

Page 5 of 16

X2

STEP 2

Parts Required Qty

Panel (A) 1

Panel (B) 1

Panel (C) 1

Panel (J) 2

Parts Required Qty

Panel (A) 1

Panel (B) 1

Panel (F) 2

22 x

d

STEP 3

j

d

B

d

A

J

C

d

B

A

FF

i

j

jj

i

j

i

Page 6 of 16

8 x

i

4 x

j

STEP 4

STEP 5

g

f

2 x

a

E

a

m

E

F

H

Parts Required Qty

Panel (E ) 1

Panel (H) 1

Parts Required Qty

Panel (F ) 1

Page 7 of 16

m

1 x

a

m

a

m

STEP 6

STEP 7

a

1 x

a

m

Page 8 of 16

F

H

E

m

1 x

a

m

a

m

F

H

E

G

Parts Required Qty

Panel (G) 1

STEP 9

Panel (I) 1

Parts Required Qty

Panel (D) 1

STEP 8

A

G

Parts Required Qty

Panel (A) 1

2 x

h

hH

F

h

Page 9 of 16

I

D

E

STEP 10

STEP 11

h

Parts Required Qty

Panel (B) 1

h

2 x

h

4 x

h

A

G

H

F

E

D

I

A

G

H

B

F

DI

E

Page 10 of 16

h

5 x

g

STEP 12

STEP 13

Parts Required Qty

Panel (C) 1

4 x

h

6 x

h

A

B

Page 11 of 16

h

D

E

F

G

A

BD

FG

C

H

h

STEP 14

STEP 15

Parts Required Qty

Panel (Z) 2

8 x

b

K

Page 12 of 16

M

L

b

X2

Panel (M) 2

Panel (L) 2

Parts Required Qty

Panel (K) 2

KM

L

Z

X2

STEP 16

STEP 17

K

Page 13 of 16

M

L

h

X2

Parts Required Qty

Panel (J) 2

Z

J

h

4 x

h

4 x

k

8 x

f

L

Z

J

L

f

k

f

k

STEP 17

STEP 18

Page 14 of 16

K

M

L

e

X2

ZJ

4 x

e

l

2 x

l

STEP 19

Page 15 of 16

Put the screw in

the top panel hole

of your furniture

Make a hole in

the wall and put

the wall plug in

Put the screw in

the wall plug hole

o

f

NOTE : Wall fixing are not supplied with this product

as different devices (such as Rawl plugs on brick

work).You must use fixing devices suitable for the

type of wall you intend to mount this product to.

Please ensure that the head of any screw used has

a diameter greater that the diameter of the mounting

hole on the product and than the fixing is safe and

secure before use.

The straps and screws to fix the strap on to

the furniture are provided only.

n

nWall Plug

1 x

oSafety strap (L-200mm)

1 x

fCsk Screw (M3.5x15mm)

1 x

Your LANCASTER CONSOLE HALL TABLE is now completely assembled

Page 16 of 16

GFW Lancaster 2 Drawer Console Table User manual

GFW Lancaster 2 Drawer Console Table User manual

Related papers

Other documents