V-ZUG 31026 Installation guide

V-ZUG
Brand
V-ZUG
Model
31026
Type
Installation guide

This manual is also suitable for

V-ZUG 31026 glass ceramic hob offers precise cooking control with its range of features. Unleash your culinary creativity with its flexible cooking zones that adapt to various pan sizes for efficient heat distribution. Enjoy safe and effortless cooking with residual heat indicators, keeping you informed about the temperature of each zone even after it's turned off. Master every dish with ease using the intuitive touch controls, allowing for precise temperature adjustments.

V-ZUG 31026 glass ceramic hob offers precise cooking control with its range of features. Unleash your culinary creativity with its flexible cooking zones that adapt to various pan sizes for efficient heat distribution. Enjoy safe and effortless cooking with residual heat indicators, keeping you informed about the temperature of each zone even after it's turned off. Master every dish with ease using the intuitive touch controls, allowing for precise temperature adjustments.

Installation instructions
Glass ceramic hob Toptronic
Frameless, for flush installation
J31004.123-2
11.10.13
1
These installation instructions apply to: 31004 (GK35TESF), 31005 (GK45TERSF), 31024 (GK45TES.1F),
31025 (GK45TEBS.3F), 31026 (GK45TEAS.1F), 31028 (GK45TEBS.2F), 31033 (GK45TEGF)
Identification plate
The identification plate is next to the connection plate.
➤ Affix the second identification plate (enclosed) in an accessible position
behind the front of the fitted cabinet beneath the appliance.
➤ Refer to the identification plate for specifications for the required mains voltage, current type and fuses.
➤ The appliance is equipped with a mains cable that should be connected to a distribution box by the customer.
The appliance should be installed by qualified personnel only. Each step must be carried out and checked in full in the order
specified.
Application height of the appliance: up to max. 2000 m above sea level
Validity
General notes
If fitting in flammable material, the guidelines and standards for low voltage installations and for the fire protection must be strict-
ly observed.
Installation accessories included
Designation Article no.
Cementing-in instructions J004.133
Sealing strip set H6.2142
Accessories
Designation Article no.
Steel angle set
for GK35TESF, GK45TES.1F, GK45TEBS.2F/3F, GK45TEGF
for GK45TERSF / GK45TEAS.1F
H6.3772
H6.3774
Thermal screen set
for GK35TESF, GK45TES.1F, GK45TEBS.2F/3F, GK45TEGF
for GK45TEAS.1F
for GK45TERSF
H6.2622
H6.2617
H6.2534
Instant adhesive for the installation of the steel angle
Permabond F246, incl. Activator, 50 ml tube. From Silitech AG, 3008 Bern.
B11.502
Cement set
Complete with cleaning agent, primer type 1105, cartridge with silicon adhesive, black with nozzle.
Suitable for all absorbent worktop materials (wood and natural stones such as marble and granite).
86.3928.85
Special primer type 107
Suitable for non-absorbent worktop materials (not suitable for polyethylene, polypropylene or Teflon).
45.2771.76
Electrical connections
Electrical connections must made by qualified personnel in accordance with the guidelines and standards for low voltage
installations and the specifications of the local electricity supply companies.
A plug-in appliance may only be connected to a socket outlet with earthing contact, installed according to specifications. An
all-pole mains isolating device with 3 mm contact opening should be provided in the house wiring system. Switches, plug and
socket devices, circuit breakers and fusible cut-outs which are accessible after installation and which have all-poles switching
are permissible as isolating devices. Effective earthing and separately installed neutral and earth conductors ensure safe and
fault-free operation. After installation, live parts and cables with basic insulation must not be accessible. Old installations should
always be checked.
Connection plate
Identification plate
Installation instructions
Glass ceramic hob Toptronic
Frameless, for flush installation
J31004.123-2
11.10.13
2
Indications
• These appliances are normally installed in stone claddings.
• The worktop must be flat and at least 30 mm thick.
• The appliance is embedded in the recess machined by the manufacturer of the stone cladding (see the enclosed cementing
instructions). Use only good quality, fresh cementing compound (black silicon) which attains the required final strength and elasticity
after a curing period of 24 hours.
• A cementing set and a special primer for non-absorbent cladding materials is obtainable (see «Accessories»).
Installing
1. Create the installation cut-out accurately.
– The mounting surface can be recessed by installing wood or stone bars or produced using the steel angle set (see
«Accessories»).
2. Prepare the cut-out and the appliance according to the information in the accompanying cementing-in instructions.
3. Lower the appliance symmetrically into the cut-out on the worktop.
4. Carefully cement the appliance in place and allow the silicon cement joints to dry for at least 24 hours.
5. Where necessary establish mains supply connection before inserting the appliance. The connection cable is not to touch the hot
parts of the metal tray under the cooking zones.
Installation
The distance from the appliance cut-out to flammable walls (left, right and rear) must be at least 41.5 mm. Parts such as par-
tition walls, reinforcing strips which protrude into the installation space under the cooking zone must be of non-flammable ma-
terials.
The distance between the underside of the appliance tray and any kitchen unit parts of flammable material must be at least
20 mm. When installed directly under a drawer and if the tray should be contactable from below without the aid of tools, the
thermal screen set must be used (see «Accessories»).
The layout of the cooking zones on the integrated hob may differ from the illustrated hob!
GK35TESF/GK45TES.1F/GK45TEBS.2F/3F,
GK45TEGF
GK45TERSF/GK45TEAS.1F
Access to the appliance from below must be guaranteed over the entire cut-out surface. For servicing, the sheet metal tray
together with the built-in parts can be taken out from below. The covers to prevent accidental contact with live parts must
be removable by unscrewing from underneath.
600/550
900
Installation pipe
Clamp
Distribution box
400V 2N~
PE/ green/yellow
N blue
L1 brown
L2 black
230 V~
PE/ green/yellow
N blue
L1 brown
400V~ 3
PE/
yellow/green
L3 grey
L2 black
L1 brown
yellow/green
grey
black
brown
PE/
400V~ 2
)
L1
L2
(30)
600
767 ±1
507±1
min. 41.5
577 ±1
571
501
761
501
507 ±1
min. 41.5
(30)
600
600/550
600/550
min. 82
(560/750)
(490)
R5
R0–5
0
-1
Y – Y
min. 20
Z
Z
Y
Y
Y
Y
max. 43
from support
Cable length 1.5 m Cable length 1.5 m
max. 43
from support
0
-0.5
8.5
0/+1
8.5
0/+1
8.5
8.5
Detail Z
Drawer/cabinet
Steel angle bonded
or screw mounted
(for adhesive see
«Accessories»)
  • Page 1 1
  • Page 2 2

V-ZUG 31026 Installation guide

V-ZUG
Brand
V-ZUG
Model
31026
Type
Installation guide
This manual is also suitable for

V-ZUG 31026 glass ceramic hob offers precise cooking control with its range of features. Unleash your culinary creativity with its flexible cooking zones that adapt to various pan sizes for efficient heat distribution. Enjoy safe and effortless cooking with residual heat indicators, keeping you informed about the temperature of each zone even after it's turned off. Master every dish with ease using the intuitive touch controls, allowing for precise temperature adjustments.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents